• Analytical Science and Technology
• /
• v.16 no.2
• /
• pp.95-101
• /
• 2003

In this study, water content in the mixture of methanol and ethanol was nondestructively measured by near infrared (NIR) spectroscopy. Two types of NIR instruments, portable NIR system with a photo-diode array and scanning type NIR spectrometer were used and the calibration results were compared. Partial least squares regression (PLSR) was applied for the calibration and validation for the quantitative analysis. The calibration results from both instruments showed good correlation with actual values. The calibration with the use of PLS model predicted water concentration with a standard error of prediction (SEP) of 0.10% and 0.12% for photo diode array and scanning type, respectively. During 6 days, routine analyses for 3%, 5% and 7% water in ethanol solution with 2% methanol were performed to validate the robustness of the developed calibration model. The routine analyses showed good results with coefficient of variation (CV) of within 3% for both types of NIR spectrometers. This study showed that the rapid determination of water in the mixture of methanol and ethanol was successfully performed by NIR spectroscopy and the performance of the portable NIR system with a photo diode array detector was comparable to that of the scanning type NIR spectrometer.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2000.10a
• /
• pp.200-205
• /
• 2000

The purpose of this study is to develop an economical radiation sensor using photo diodes. An electronic circuit was developed. The behavior of the radiation sensor was evaluated by increasing number of photo diodes. The sensor became more reliable by the increase in number of photo diodes. It was showed that the photo diodes sensor would be applicable.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1429-1434
• /
• 2003

A number of dust particles are intruded into ODD(Optical disk drive) due to the flow caused by disk rotation and are adhered to a lens or disk surface. The space between the disk and the lens is being reduced. Someone indicates the problems of this drive that are relatively small data storing capacity and slow access time. In recent, the problems of this optical disk drive mentioned above are being solved by adding the speed of the disk's revolution, making the actuator high-speed or light, and making the beam spot size smaller than making the space narrow between disk and lens. These particle contamination affects seriously RF Signal, readout signal in an ODD. Especially, the affected parts by a particle contamination in an ODD's readout signal are objective lens and media.

• Journal of Satellite, Information and Communications
• /
• v.8 no.1
• /
• pp.71-76
• /
• 2013

In this paper, a transceiver of VLC (Visible Light Communication) using LED white lighting has been implemented. The transmitted waveforms of LED and PD (Photo Diode) of the received signal are analyze to restore VLC data. Audio signal was successfully transmitted to demonstrate possibility and potential of optical wireless communication systems. Various modulation formats are considered to evaluate and compare performance in diverse channel conditions.

• Journal of Biomedical Engineering Research
• /
• v.5 no.2
• /
• pp.149-154
• /
• 1984

A digital X-ray system was designed using photo-diode arrays. This system consists of the following five sub-units; (1) slit and driving system (2) X-ray detection system (3) data-conversion system (4) computer (5) image display system. Using this system, one can obtain scatter-free, high contrast, digitally formatted, high quality image, as compared with the conventional film-based X-ray system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.100-103
• /
• 2003

Signal detection technologies such as fluorescence, charge and electrochemical detection used in the monolithic capillary electrophoresis system to convert the biochemical reaction into the electrical signal. The fluorescence detection using photodiodes that measure fluorescence emitted from eluting molecules is widely used for the monolithic capillary electrophoresis system. In this paper, in order to fabricate a photosensor has the increased sensitivity, we investigated on the sensitivity of general type and p-i-n type diode. The p-i-n diode has higher sensitivity than photodiode. Considering these results, we fabricated p-i-n diodes on the high resistive$(4k{\Omega}{\cdot}cm)$ wafer into rectangle and finger pattern and compared internal resistance of each pattern. The internal resistance of p-i-n diode can be decreased by the application of finger pattern has parallel resistance structure from $571{\Omega}$ to $393{\Omega}$.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.373-379
• /
• 2022

In this paper, since the APD(Avalanche Photo Diode) for LTV(Light to Voltage) conversion uses a high voltage in the operating range unlike other PD(Photo Diode)s, the quenching resistor must be connected in series to prevent overcurrent when using the TIA(Transimpedance Amplifier). In such a case, quenching resistance may affect the transfer function of the TIA circuit, resulting in serious stability. Therefore, in this paper, by analyzing the effect of APD quenching resistance on the voltage and current loop transfer function of TIA, we propose a loop analysis and a method for determining the quenching resistance value to improve stability. TIA circuit with quenching resistance was designed by the proposed method and the stability of operation was verified through simulation and chip fabrication.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.11
• /
• pp.654-659
• /
• 2005

An improved power supply for APD(Avalanche Photo Diode) with a received optical power monitoring circuit allows the received optical power increase temporary without of the degradation of the electrical signal. For the cost reduction and simple fabrication, an improved power supply has been proposed that it was designed for driving a APD as a receiving device of a wireless optical transmission system. It was demonstrated that it was possible to improve a dynamic range by compensating the temperature coefficient of the APD up to 1.0 V/$^{\circ}C$ through the power supply. Also, for an efficient transmission at the receiver end, a simple structure of a single cylindrical micro-lens configuration was used in conjunction with the laser diode to partially compensate a laser beam ellipticity. For this purpose, an astigmatism introduced by the micro-lens is utilized for the additional compensation of the beam ellipticity at the receiver end. In this paper, it is demonstrated that an efficient beam shaping is realized by using the proposed configuration consisting of the single lens attached to the laser diode.

• 전자공학회논문지 IE
• /
• v.46 no.4
• /
• pp.8-15
• /
• 2009

In this paper, we are indicated CMOS Image sensor circuit SPICE analysis for the Photo Diode and pixel Modeling. We get a characteristic of the photoelectric current using a device simulator Medici and develop the Photodiode model for applying a SPICE simulation. For verifying the result, We compared the result of SPICE simulation with the result of mixed mode simulation about the testing circuit structure consisted photodiode and NMOS.

• Journal of Sensor Science and Technology
• /
• v.17 no.1
• /
• pp.41-52
• /
• 2008

In this paper, a circuit analysis of the complementary CMOS active pixel and readout circuit is carried out. Complementary pixel structure which is different from conventional 3TR APS structure is consist of photo diode, reset PMOS, several NMOSs and PMOSs sets for complementary signals. Photo diode is modelled with Medici device program. HSPICE was used to analyze the variation of the signal feature depending on light intensity using $0.5{\mu}M$ standard CMOS process. Simulation results show that the output signal range is from 0.8 V to 4.5 V. This signal range increased 135 % output dynamic range compared to conventional 3TR pixel in the condition of 5 V power supply.