• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.2026-2028
• /
• 2002

본 논문에서는 실리콘 기판상의 전송선로 특성을 개선하기 위하여 표면 마이크로머시닝 기술을 이용하여 $10{\mu}m$ 두께의 다공질 실리콘 산화막으로 제조된 기판 위에 에어브리지를 가진 CPW 전송선로와 phase shifter를 제작하였다. 간격이 $30{\mu}m$, 신호선이 $80{\mu}m$인 CPW 에어브리지 전송선의 삽입손실은 4 GHz에서 -0.25 dB이며, 반사손실은 -28.9 dB를 나타내었다. CPW phase shifter의 크기는 S-W-$S_g$ = 100-30-400 ${\mu}m$로 설계되었다. "ㄷ" 모양을 가진 에어브리지의 폭은 $100{\mu}m$. 길이는 400-460-400 ${\mu}m$이다. 낮은 손실을 얻기 위한 Step된 에어브리지를 가진 phase shifter 구조가 step이 없는 에어브리지를 가진 구조보다 삽입손실이 보다 더 향상되었다. 제작된 CPW phase shifter의 위상특성은 28 GHz의 넓은 주파수 범위에서 $180^{\circ}E 의 천이를 타나내었다. 이상과 같은 결과로부터 두꺼운 다공질 실리콘은 고 저항 실리콘 집적회로 공정에서 고성능 저가의 마이크로파 및 밀리미터파 회로 응용에 충분히 활용 될 수 있으리라 기대된다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.130-136
• /
• 2014

This paper reviews the research on silicon based phased array system operating from microwave to millimeter wave frequencies. First, the design of phase shifter using CMOS technology is presented. The passive phase shifter is applied to the transmit/receive module from one to 16 channel in a single chip. The 35 GHz 4-element T/R module consumes less than 200 mW both transmit and receive modes. The architecture can extend to 16-channel operating at 44 GHz, thereby improving transmit power and linearity. The Ku-band 2-antenna 4-element receiver was developed using active phase shifter based on vector sum method. It is important to minimize coupling between beams because the chip contains four independent beams. The method of coupling is presented and verified.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.432-434
• /
• 1994

This paper describes a phase-shifter which can flexibly adjust the active and reactive power flow through an ac transmission line. The phase-shifter has two voltage-source converters sharing an energy storage capacitor. The magnitude of the injected voltage is controlled by the converter I connected in parallel with the sending terminal, while that of phase angle by the converter II in series with the line through the coupling transformer. In order to analyze the whole system operation, an equivalent circuit model was developed and verified by a computer simulation with EMTP code.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.161-164
• /
• 2002

In this paper, a design technique is introduced for designing a 360-degree linear analog phase shifter at 1.8㎓. Using tunable short-circuit terminated comb-line filters as reactive loads, the circuit gives a very small insertion loss(less than 0.1㏈) and an almost linear phase shifter over the filter bandwidth for the full 360-degree range. We were showed large phase variation with small capacitance variation in the quadrature hybrid coupler using tunable shorted terminated combline filters.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.215-218
• /
• 2002

In this paper, we propose a microstrip line tunable phase shifter. If we vary the applied bias voltage, the relative dielectric constant of ferroelectrics also changes and we designed tunable phase shifter using Au/BSTO/MgO/Au structure. We also used a coupling structure to increase the amount of phase shift at certain frequency in a limited size and we could reduce the loss by reducing the line width.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.6
• /
• pp.602-612
• /
• 2013

In this paper, a design and fabrication of miniaturized 5.3 GHz reflection type $360^{\circ}$ analog phase shifter with branch line coupler and $360^{\circ}$ variable reactance load. In order to miniaturize phase shifter, novel branch line coupler is proposed. The novel branch line coupler is miniaturized using transformation of transmission line to T and ${\pi}$ type equivalent circuit. The miniaturized branch line coupler has small size of above 50 % compared with conventional branch line coupler. For wide phase shift range, $360^{\circ}$ variable reactance load structure is adopted. Especially, the structure was improved for linear phase shift by adding transmission line which acts as an impedance transformer. The improved structure was miniaturized using the equivalent lumped-element of transmission line. The fabricated phase shifter with $15{\times}15mm^2$ shows wide phase shift of above $480^{\circ}$, the insertion loss of -4~-6 dB and the reflection loss of below -20 dB at 5.3 GHz under 0~10 V control voltage range.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.9
• /
• pp.392-397
• /
• 2003

Reflection type phase shifter with Lange coupler is widely used as a circuit topology to obtain phase shift in broadband operation. The phase shift of 33.75$^{\circ}$ at this type is achieved by simultaneously turning on both 11.25$^{\circ}$ and 22.5$^{\circ}$ . In order to improve the phase accuracy of 33.75$^{\circ}$, this paper proposes the additional circuit which is composed of a GaAs PIN diode and a reactive load. By utilizing MMIC technology. Over the 2-6 GHz band, the measured result of phase difference between the previous circuit and the proposed circuit shows average 4.7$^{\circ}$ on the basis of 33.75$^{\circ}$. Insertion loss and return loss are invariant in comparison with the previous circuit.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.10
• /
• pp.1145-1150
• /
• 2012

In this paper, an improved Schiffman phase shifter is proposed using slot-coupled lines. It consists of the typical coupled lines and a simple rectangular slot which is placed in the ground plane underneath the coupled lines. Phase responses of the slot-coupled Schiffman phase shifter are analyzed in consideration of the phase velocity of two independent transmission modes and the characteristic impedance of slot-coupled line. The $905^{\circ}$ Schiffman phase shifters with high impedance ratio is realized at 2.4 GHz, which cannot be implemented with the conventional coupled lines. The measured results show that the bandwidth is around 74.2 % within the phase errors ${\pm}5^{\circ}$. The measured return loss is found to be better than 15.0 dB and insertion loss is less than 1.5 dB over the operating frequency band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.7
• /
• pp.721-727
• /
• 2014

In this paper, an broadband Schiffman phase shifter is proposed using vertically installed coupled lines. It consists of the typical coupled lines and a extra coupled lines which is installed vertically on the original coupled lines plane. Phase responses of Schiffman phase shifter with vetically installed coupled lines are analyzed in consideration of the phase velocity of two independent transmission modes and the characteristic impedances. The $90^{\circ}$ Schiffman phase shifters with high impedance ratio is realized at 2.4 GHz, which cannot be implemented with the conventional coupled lines. The measured results show that the bandwidth is 1.5~3.2 GHz(70.8 %) within the phase errors ${\pm}5^{\circ}$. The measured return loss is found to be better than 12.4 dB and insertion loss is less than 1.2 dB over the operating frequency band.

• 한국정보통신설비학회:학술대회논문집
• /
• 2003.08a
• /
• pp.286-288
• /
• 2003

In this paper, in order to obtain a large differential phase shift with a little change in applied voltage, a ferroelectric reflective load circuit has been designed on top of barium strontium titanate $(Ba,Sr)TiO_3$ [BST] thin film. The design of the ferroelectric reflection-type phase shifter is based on a reflection theory of terminating circuit, which has a reflection-type analogue phase shifter with two ports terminated in symmetric phase-controllable reflective networks. To achieve large amounts of phase shift in low bias-voltage range, the effects of change of capacitance and transmission line connected with two coupled ports of a 3-dB $90^{\circ}$ branch-line hybrid coupler have been investigated. A large phase shift with a small capacitance change in the parallel terminating circuit has been demonstrated in the paper.