• 한국전기전자재료학회논문지
• /
• 제32권1호
• /
• pp.64-69
• /
• 2019

Methylammonium lead triiodide ($MAPbI_3$)-based perovskite solar cells potentially have potential advantages such as high efficiency and low-cost manufacturing procedures. However, $MAPbI_3$ is structurally unstable and has low phase-change temperatures ($30^{\circ}C$ and $130^{\circ}C$); it is necessary to solve these problems. We investigated the crystal structure and phase separation using real-time temperature-change X-ray diffraction, transmission electron microscopy, and electron energy loss spectroscopy. $MAPbI_3$ has a tetragonal structure, and at about $35^{\circ}C$ the c-axis contracts, transforming $MAPbI_3$ into the related cubic crystal structure. In addition, at $130^{\circ}C$, phase separation occurs in which $CH_3NH_2$ and HI at the center of the unit cell of the perovskite structure are extracted by gas, leavingand only $PbI_2$ of the three-component structure, is produced as the final solid product.

• Transactions on Electrical and Electronic Materials
• /
• 제6권2호
• /
• pp.35-38
• /
• 2005

Pb(Zr$_{0.8}$Ti$_{0.2}$)O$_{3}$ powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT thick films were fabricated by the screen-printing techniques on Pt/Ah03 substrates. The structural properties were examined as a function of sintering temperature. The particle size distribution of the PZT powder derived from the sol-gel process is uniform with the mean particle size of about 2.6 m. As a result of the DTA, the formation of the polycrystalline perovskite phase was observed at around $890^{circ}$CC. In the X-ray diffraction analysis, all PZT thick films showed a perovskite polycrystalline structure without a pyrochlore phase. The perovskite crystallization temperature of PZT thick films was about $890^{circ}$C. The average thickness of the PZT thick films was approximately 80-90 m.

• 한국재료학회지
• /
• 제33권8호
• /
• pp.344-351
• /
• 2023

Cesium lead iodide (CsPbI₃) with a bandgap of ~1.7 eV is an attractive material for use as a wide-gap perovskite in tandem perovskite solar cells due to its single halide component, which is capable of inhibiting halide segregation. However, phase transition into a photo inactive δ-CsPbI₃ at room temperature significantly hinders performance and stability. Thus, maintaining the photo-active phase is a key challenge because it determines the reliability of the tandem device. The dimethylammonium (DMA)-facilitated CsPbI₃, widely used to fabricate CsPbI₃, exhibits different phase transition behaviors than pure CsPbI₃. Here, we experimentally investigated the phase behavior of DMA-facilitated CsPbI₃ when exposed to external factors, such as heat and moisture. In DMA-facilitated CsPbI₃ films, the phase transition involving degradation was observed to begin at a temperature of 150 ℃ and a relative humidity of 65 %, which is presumed to be related to the sublimation of DMA. Forming a closed system to inhibit the sublimation of DMA significantly improved the phase transition under the same conditions. These results indicate that management of DMA is a crucial factor in maintaining the photo-active phase and implies that when employing DMA designs are necessary to ensure phase stability in DMA-facilitated CsPbI₃ devices.

• Current Photovoltaic Research
• /
• 제11권3호
• /
• pp.87-95
• /
• 2023

As the demand for the Internet of Things grows, research into indoor photovoltaics for wireless power is becoming important. In particular, perovskite has attracted considerable attention due to its superior performance compared to other candidates. However, various surface defects present in perovskite are a limiting factor for high performance. In particular, deep-level surface defects caused by uncoordinated Pb²⁺ ions directly limit charge transport. In low light environments, this appears to be a more significant hurdle. In this study, ethylenediamine, which can provide covalent bonding to uncoordinated Pb²⁺ ions through nitrogen, was used as a surface treatment material for indoor photovoltaics. X-ray photoelectron spectroscopy confirmed that the uncoordinated Pb²⁺ ions were effectively passivated by the terminal nitrogen of ethylenediamine. As a consequence, a V_OC of 0.998 V, a JSC of 0.139 mA cm^-2 and a fill factor of 83.03% were achieved, resulting in an indoor photoelectric conversion efficiency of 38.02%.

• 한국세라믹학회지
• /
• 제19권4호
• /
• pp.300-308
• /
• 1982

A new perovskite type compound, (Pb1a-χKy□χ-y) (Zr0.33Ti0.67)O3-χ+y/2 was proposed and synthesized by "Wet-Dry Combination Technique". This defect ferroelectric material was characterized by partial substitutions of K+ for Pb+2 in Pb(Zr0.33Ti0.67)O3. This material was mono-phasic perovskite compound at 800℃ for 1hr., but ZrO2 was more or less isolated from the (Pb1a-χKy□χ-y) (Zr0.33Ti0.67)O3-χ+y/2. As a result, snitering temperature, sintered density, curie temperature, and dielectric constant of test pieces decreased and a-axis was nearly constant, while c-axis gradually decreased with the value x in the region of tetragonal phase of PZT. It was also recognized that the defect structure caused by adding K+ was found in both A-site cation and O-site anion vacancies in the defect PZT.

• 한국전기전자재료학회논문지
• /
• 제15권10호
• /
• pp.870-875
• /
• 2002

Ba(Zn$_1$-xCox)TaO$_3$[BZCT] ceramics were Prepared by the conventional mixed oxide method. The ceramics were sintered at the temperature of 1450∼1550$\^{C}$ for 5 hr in air. The crystal structure of BZCT ceramics was investigated by the XRD. The microstructure of the specimens were observed by SEM. The structural properties of BZCT specimens were investigated as a function of composition and sintering temperature. All BZCT ceramics sintered over 1550$\^{C}$ were showed a polycrystalline complek perovskite structure without second phases and any unreacted materials. The density of BZCT (70/30) specimen sintered at 1550$\^{C}$ was 6.31g/㎤. In the case of the BZCT(70/30) ceramics sintered at 1550$\^{C}$ for 5 hours, dielectric constant, qualify factor and temperature coefficient of resonant frequency for microwave dielectrics application were a good value of 29, 16,468 at 10㎓ and -4.4 ppm/$\^{C}$, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.371-374
• /
• 2002

Bismuth lanthanum titanate thin films with excess Bi contents were prepared onto Pt/Ti/$SiO_2$/Si substrate by metalorganic decomposition (MOD) technique. The structure and morphology of the films were analyzed using X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. From the XRD analysis, BLT thin films show polycrystalline structure and the layered-perovskite phase was obtained over 10% excess of Bi contents. As a result of ferroelectric characteristics related to the Bi content of the BLT thin film, the remanent polarization and dielectric constant decreased with increasing over Bi content of 10 % excess. The BLT film with Bi content of 10% excess was measured to have a dielectric constant of n9 and dielectric loss of 1.85[%]. The BLT thin films showed little polarization fatigue test up to 3.5 x $10^{9}$ bipolar switching cycling.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.714-718
• /
• 2003

Usually for the commercial preparation of barium titanate films or ceramics the reaction atmosphere must be preferably in air. However, normally air is not used because it contains carbon dioxide, which can easily react with barium to form the undesired product barium carbonate, leading to unwanted second-phase formation in the (mal stages of the process. In the present work a series of perovskite barium titanate films was prepared by the sol-gel method, using a metal alkoxide solutions in the electrophoretic deposition (EPD). The influence of several process parameters, like sintering temperature of sol preparation before EPD and heat-treatment temperature and non-oxidized atmosphere, on the film properties is described.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.196-199
• /
• 2000

Since the reports of CMR(colossal magnetoresistance) effects in some single crystal R-P phase $La_{1+x}Sr_{2-x}Mn_2O_7$, considerable researches have been carried out to find optimum composition and to understand the role of dimensionality in the CMR mechanism of this system. In this study, layered perovskite $Ln_xCa_{1-x}MnO_{4}$ (x=0.5, Ln=Pr, Nd, Sm, Gd) phases were synthesized by solid state reaction and their structures were refined by Rietveld method. Electrical and magnetic properties were measured between room temperature and liquid helium temperature and compared with those of two dimensional $La_{1.4}Sr_{1.6}Mn_2O_7$ phase.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.240-241
• /
• 2005

비 직선적 정(+) 저항온도계수 특성을 갖는 PTC thermistor는 전이온도(큐리점) 부근에서 온도변화에 대하여 극히 큰 저항 값의 변화를 나타내는 산화물계반도체 저항기(또는 발열체)로써, 일반적으로 반도체의 온도-저항 특성과 같이 상온영역에서 온도의 상승과 함께 부성저항 특성을 나타내다가 온도가 점점 증가하여 큐리점 부근에 도달하면 저항이 급격히 증가하는 독특한 특성을 갖는다. Perovskite 구조의 $BaTiO_3$를 주성분으로 미량의 Dopant를 첨가하여 도전성을 갖게 한 N형 반도체의 일종으로 저항-온도 특성 전류-전압 특성, 전류감쇄 특성 등을 이용하여 과전류 보호회로, 히터, TV 소자회로(degausser), 모터기동회로, 온도센서, 정온발열기기 등으로 널리 사용된다. 본 연구는 큐리점 부근의 급격한 저항변화 현상과 결정입계의 전위장벽 형성 및 그에 따른 정온발열 기능의 상관성으로부터 그 응용성을 조사하였다.