• Resources Recycling
• /
• v.15 no.4 s.72
• /
• pp.3-12
• /
• 2006

The feasibility for the employment of manganese nodule as an adsorbent for $SO_{2}$ gas has been investigated. The specific surface area of manganese nodule particle, which used in the experiments, was ca. $221.5m^{2}/g$ and the content of sulfur in manganese nodule was observed to significantly increase after $SO_{2}$ was adsorbed on it. The EPMA for the distilled water-washed and methanol-washed manganese nodule particle after $SO_{2}$ adsorption showed that its sulfur content was slightly decreased to 14.7% and 13.1% respectively, from 15.4% before washing. The XRD analysis of manganese nodule showed that todorokite and birnessite, which are manganese oxides, and quartz and anorthite were the major mineralogical components and weak $MnSO_{4}$ peaks were detected after $SO_{2}$ was adsorbed on manganese nodule. For an comparative investigation, limestone was also tested as an adsorbent for $SO_{2}$, however, no peaks for $CaSO_{4}$ were found by XRD analysis after the adsorption of $SO_{2}$. As the size of adsorbent increased, time for breakthrough was decreased and the adsorbed amount of $SO_{2}$ was also diminished. The $SO_{2}$ adsorption was hindered when its flow rate became high and the adsorption capacity of manganese nodule was observed to be superior to that of limestone. In addition, the mixture of manganese nodule and limestone did not show an increase in the adsorption of $SO_{2}$. Finally, as the temperature was raised, the adsorbed amount of adsorbate on manganese nodule was found to be decreased.

• Journal of Korean Society of Forest Science
• /
• v.79 no.2
• /
• pp.127-137
• /
• 1990

This study was carried out to investigate some characteristics of selected trees recognized as natural hybrid between Pinus densiflora and Pinus thunbergii for improving resistance to pine leaf gall midge. The results obtained were as follows. l. In the mean annual increment and the growth in the period of latest 5 years of DBH, hybrid pines showed intermediate value of the parents, Pinus densiflora and Pinus thunbergii. However, there was remarkable variation among individuals of hybrid pine. 2. The trees having resin duct index(RDI) value larger than 0.1 for the position of resin duct in needle was classified as hybrid pine. The leaf and leaf sheath of Pinus thunbergii was longer than that of Pinus densiflora and the distance between rows of stomata on needles of Pinus thunbergii was longer than that of Pinus detasiflora, and the values of those observations on hybrid pine were intermediate between the parent species. However, differences among individual was observed. 3. In the size of cone and seed, and weight of 1000 seeds, like in the leaf characteristics, Pinus thunbergii showed higher value than Pinus densiflora and those values of hybrid were intermediate between the parent species. 4. Assuming isoenzyme ADH-$B_2$, ME-$A_2$, PGI-$B_1$, and PGI-$B_2$ alleles observed in the hybrids were introgressed from Pinus thunbergii, the hybrid pine can be easily identified by these isoenzyme alleles. However, the individuals which do not have those alleles can not be identified.

• Journal of Korean Society of Forest Science
• /
• v.79 no.4
• /
• pp.367-375
• /
• 1990

In order to determine the effects of bedrock, organic matter, calcium and iron oxide on the soil aggregation, this research has performed with soils from bedrock regions of Limestone, Granite and Granite gneiss. This research was also to estimate how organic matter, calcium and iron oxide influence on soil aggregation under different forest conditions in various bedrock regions. And it also had a purpose to rate physical factors relevant to soil aggregation, their characteristics and aggregate diameter which closely relates to stabilities in the process of soil erosion. The following conclusions have been drawn in response to the overall research objectives. The rates of the soil aggregation on different bedrock regions were 21% in Limestone bedrock, 19.8% in Granite bedrock and 9.9% in Granite gneiss bedrock. A main factor in soil aggregation was the orgainc matter content in soils and the rate of soil aggregation increased in the constant proportion with the organic matter content. The relation could be formulated into Y=4.31X-4.37(Y : aggregation ratio X : organic matter content). The soil aggregation ratio under the deciduous forests eras higher than that under the coniferous forests. It was considered that this resulted from differences in organic matter content. Soil aggregates with larger diameter than 0.5mm were found more in Limestone bedrock than other smaller size soil aggregates of 0.25mm diameter were more distributed in Granite gneiss bedrock. Granite bedrock region had normal distribution in soil aggregate sizes with the highest frequency of 0.5mm diameter. Calcium and iron oxides had only partial influences on the soil aggregation in some specific conditions. But in Limestone bedrock region calcium influenced on the soil aggregation with the organic matter content.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.3
• /
• pp.46-55
• /
• 2016

This work proposes a 13b 100MS/s 45nm CMOS ADC with a high dynamic performance for IF-domain high-speed signal processing systems based on a four-step pipeline architecture to optimize operating specifications. The SHA employs a wideband high-speed sampling network properly to process high-frequency input signals exceeding a sampling frequency. The SHA and MDACs adopt a two-stage amplifier with a gain-boosting technique to obtain the required high DC gain and the wide signal-swing range, while the amplifier and bias circuits use the same unit-size devices repeatedly to minimize device mismatch. Furthermore, a separate analog power supply voltage for on-chip current and voltage references minimizes performance degradation caused by the undesired noise and interference from adjacent functional blocks during high-speed operation. The proposed ADC occupies an active die area of $0.70mm^2$, based on various process-insensitive layout techniques to minimize the physical process imperfection effects. The prototype ADC in a 45nm CMOS demonstrates a measured DNL and INL within 0.77LSB and 1.57LSB, with a maximum SNDR and SFDR of 64.2dB and 78.4dB at 100MS/s, respectively. The ADC is implemented with long-channel devices rather than minimum channel-length devices available in this CMOS technology to process a wide input range of $2.0V_{PP}$ for the required system and to obtain a high dynamic performance at IF-domain input signal bands. The ADC consumes 425.0mW with a single analog voltage of 2.5V and two digital voltages of 2.5V and 1.1V.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.7
• /
• pp.1218-1226
• /
• 2008

With the development of semiconductor integrated technology and with the increasing use of multimedia functions in computer, more functions have been implemented as hardware. Nowadays, most microprocessors beyond 32 bits generally implement an integer multiplier as hardware. However, as for a divider, only specific microprocessor implements traditional SRT algorithm as hardware due to complexity of implementation and slow speed. This paper suggested an algorithm that uses a multiplier, 'w bit $\times$ w bit = 2w bit', to process $\frac{N}{D}$ integer division. That is, the reciprocal number D is first calculated, and then multiply dividend N to process integer division. In this paper, when the divisor D is '$D=0.d{\times}2^L$, 0.5 < 0.d < 1.0', approximate value of ' $\frac{1}{D}$', '$1.g{\times}2^{-L}$', which satisfies ' $0.d{\times}1.g=1+e$, $e<2^{-w}$', is defined as over reciprocal number and then an algorithm for over reciprocal number is suggested. This algorithm multiplies over reciprocal number '$01.g{\times}2^{-L}$' by dividend N to process $\frac{N}{D}$ integer division. The algorithm suggested in this paper doesn't require additional revision, because it can calculate correct reciprocal number. In addition, this algorithm uses only multiplier, so additional hardware for division is not required to implement microprocessor. Also, it shows faster speed than the conventional SRT algorithm and performs operation by word unit, accordingly it is more suitable to make compiler than the existing division algorithm. In conclusion, results from this study could be used widely for implementation SOC(System on Chip) and etc. which has been restricted to microprocessor and size of the hardware.

• FLOWER RESEARCH JOURNAL
• /
• v.16 no.4
• /
• pp.299-303
• /
• 2008

An Oriental lily cultivar 'Pacific Wave' was released in 2007 at National Institute of Horticultural and Herbal Science, Rural Development Administration (RDA), Suwon, Korea. The crossing was made in 1999 between Oriental lily 'Simplon', an outward-facing and white colored cultivar, and 'Spinoza', pink colored cultivar. The first selection was done in 2003 with a line of 'O-03-16'. Multiplication and bulb growth, and performance test was conducted from 2004 to 2006. This selection was later on given as 'Pacific Wave' in 2007 at NHRI. Flowering time of 'Pacific Wave' in plastics house culture is mid June and grows average 115 cm. Flowers are upward-facing with 20.1 cm in diameter and white with yellow centered (RHS W155C + Y9A). Mean petal length and width is 12.2 cm and 4.2 cm, respectively. Leaves are 12.3 cm long, 2.9 cm wide. The throat color is green. It shows gray and purple stigma, and red brown pollen. The weight and size of bulb is 82.5 g and 19.6 cm, respectively. Year-round flowering can be by storing the bulb under -1 to $-2^{\circ}C$ conditions. It is necessary to add calcium to the fertilizer or remove side scales to prevent leaf scorch. It is needed to control Botrytis disease in summer wet season.

• Journal of agriculture & life science
• /
• v.45 no.6
• /
• pp.95-108
• /
• 2011

The food quality characterization and safety Japanese flying fish roe (JFF-R), capelin roe (C-R), Pacific herring roe (PH-R) were investigated. The size of JFF-R was 1.48-1.93 mm, which was longer than those of C-R and PH-R. The moisture content of JFF-R imported from Peru (JFF-R-P) was 70.3%, which was higher than that of JFF-R imported from China (JFF-R-C) (67.4%), while was lower than that of JFF-R imported from Indonesia (JFF-R-I) (83.3%). However, the salinity of JFF-R-P was 13.6%, which was lower than that of JFF-R-C, while was higher that of JFF-R-I (1.8%). The moisture contents and salinities of the other fish roes were 80.4% and 3.2%, respectively, for capalin roe, and 65.4% and 20.0%, respectively, for Pacific herring roe. According to the results of pH, volatile basic nitrogen content, heavy metal content, viable cell count and coliform group, the fish roes could be used as sanitary sources for preparation of seasoned JFF-R. The major fatty acids of fish roes were 16:0 (27.8-30.5%), 18:1n-9 (7.2-8.0%), 20:5n-3 (5.6-8.2%) and 22:6n-3 (22.0-25.6%) in JFF-R, and 16:1n-7 (6.7-9.3%) as well as these fatty acids in C-R and PH-R. Total amino acid contents of fish roes ranged from 9.44 g/100 g to 10.39 g/100 g and their major amino acids were aspartic acid, glutamic acid, leucine and lysine. The mineral content of JFF-R were higher than those of the other fish roes expected for zinc of JFF-R-I. According to the results of sensory evaluation, the color and texture of JFF-R-P were superior to those of the other fish roes. No difference was, however, found in flavor, among JFF-R-P and the other fish roes.

• Journal of agriculture & life science
• /
• v.45 no.2
• /
• pp.21-28
• /
• 2011

Hibiscus cannabinus L is a plant in the Malvaceae family. Kenaf was seeded at June 1st in 2010 and harvested at November 18th and dried and evaluated worth as a bulking agent for livestock composting. Harvested and dried Kenaf was divided into the bast, core and leaf. All materials were grinded by hammer mill and the moisture absorption, moisture evaporation, pH, volume weight and C/N ratio were measured. Kenaf was higher water absorption and evaporation ability than those of sawdust and chaff. The pH values of Kenaf were pH $2.8{\pm}0.01$ - $4.34{\pm}0.02$, which is lower pH value than those of sawdust (pH $5.28{\pm}0.01$) and chaff (pH $6.3{\pm}0.02$). The C/N ratio of Kenaf showed 649 of core, 204 of bast and 70 of leaf, which were lower than sawdust (789.1) but higher than chaff (132). In volume weight test, the materials were divided by particle size of Kenaf, named as group A(${\geq}4cm$), B(${\leq}4cm$, ${\geq}0.25cm$) and C(${\leq}0.25cm$). The volume of weight of group A and B for core, bast and leaf showed similar, but group C showed higher than those of sawdust and chaff. Especially, the volume weight of group C for leaf was 5 times higher than those of sawdust and chaff. This study suggested the possibility of using Kenaf as a bulk agent for composting of livestock manure. This is considered that strengthen the competitiveness of farmers through reducing the cost, prevention of environmental pollution caused by livestock manure and environmentally friendly processing of livestock manure.

• FLOWER RESEARCH JOURNAL
• /
• v.19 no.3
• /
• pp.127-138
• /
• 2011

Four different plant growth retardants (PGRs), paclobutrazol, flurprimidol, daminozide, and chlormequat, were applied to potted Saxifraga rosacea 'Kumoma' and 'Kumoma-Gusa' plants for control of the growth and flowering. Paclobutrazol (10, 20, 40, $80mg{\cdot}L^{-1}$), flurprimidol (5, 10, 20, $40mg{\cdot}L^{-1}$), daminozide (500, 1000, 2000, $4000mg{\cdot}L^{-1}$), and chlormequat (50, 100, 200, $400mg{\cdot}L^{-1}$) were applied to the plants by a foliar spray or drenching. In 'Kumoma', application of $40mg{\cdot}L^{-1}$ paclobutrazol by a foliar spray or drenching reduced plant height by 12.5 and 12.6 cm, and flower length by 3.4 and 3.3 cm, respectively. On the other hand, in 'Kumoma-Gusa', drenching of paclobutrazol reduced plant height by 10.7 to 12.6 cm and flower length by 2.0 to 3.9 cm with increasing concentration, but the number of florets almost fell to 20 as compared to 40.5 in the control. 'Kumoma-Gusa' plants drenched with $80mg{\cdot}L^{-1}$ paclobutrazol and sprayed with $40mg{\cdot}L^{-1}$ flurprimidol had the shortest heights of 10.7 and 9.9 cm, and floral length of 2.0 and 1.5 cm, respectively. A flurprimidol drenching at $40mg{\cdot}L^{-1}$ delayed the harvest by 3-13 days as compared to the control and the smallest number of florets, 15.6, was observed in this treatment. In both cultivars, chlormequat and daminozide did not effectively influence the growth and flowering. However, number of florets increased to more than 41 at all concentrations and up to 63, the greatest floret number, with chlormequat drench in 'Kumoma-Gusa'. These results demonstrated that over $40mg{\cdot}L^{-1}$ of paclobutrazol or 5 to $20mg{\cdot}L^{-1}$ of flurprimidol could be used as PGRs to control the growth of floral length and flowering for improving potted plant quality in S. rosacea 'Kumoma' and 'Kumoma-Gusa'.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.3
• /
• pp.209-213
• /
• 2019

Recently, demand for high energy density and long cycling stability of energy storage system has increased for application using with frequency regulation (F/R) in power grid. Supercapacitor have long lifetime and high charge and discharge rate, it is very adaptable to apply a frequency regulation in power grid. Supercapacitor can complement batteries to reduce the size and installation of batteries. Because their utilization in a system can potentially eliminate the need for short-term frequent replacement as required by batteries, hence, saving the resources invested in the upkeep of the whole system or extension of lifecycle of batteries in the long run of power grid. However, low energy density in supercapacitor is critical weakness to utilization for huge energy storage system of power grid. So, it is still far from being able to replace batteries and struggle in meeting the demand for a high energy density. But, today, LIC (Lithium Ion Capacitor) considered as an attractive structure to improve energy density much more than EDLC (Electric double layer capacitor) because LIC has high voltage range up to 3.8 V. But, many aspects of the electrochemical performance of LIC still need to be examined closely in order to apply for commercial use. In this study, in order to improve the capacitance of LIC related with energy density, we designed new method of pre-doping in anode electrode. The electrode in cathode were fabricated in dry room which has a relative humidity under 0.1% and constant electrode thickness over $100{\mu}m$ was manufactured for stable mechanical strength and anode doping. To minimize of contact resistance, fabricated electrode was conducted hot compression process from room temperature to $65^{\circ}C$. We designed various pre-doping method for LIC structure and analyzing the doping mechanism issues. Finally, we suggest new pre-doping method to improve the capacitance and electrochemical stability for LIC.