• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.3
• /
• pp.47-52
• /
• 2008

This investigation was performed in order to study the properties of deposition and layers by Silicon Dioxide, SiO2, as dielectric onto Via and Trench which have high Aspect Ratio (AR). Thus, in order to confirm these properties, three types of CVD, which were PECVD, PETEOS, and ALD, were selected. On the experiment each of the property sections was estimated that step overage of PECVD: <30%, PETEOS: 45%, ALD: 75% and the RSM of PECVD: 27.8 nm, PETEOS: 2.1 nm, ALD: <2.0 nm. As a result of this experiment for the property of electric film, ALD was valuated to be the most favorable outcome. However, ALD was valuated to have the least quality for the deposition rate. ALD deposition rate, $10\;\AA/min$ by $1\;\AA$/1cycle, was prominently lower than PETEOS, which had the deposition rate of $5000\;\AA$/min. Since electric film requires at least $1000\;\AA$ thicknesses, ALD was not suitable for the deposition rate. which is the most important component in a practical use. Therefore, in this particular study, PETEOS was evaluated to be the most suitable recipe.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.1
• /
• pp.15-20
• /
• 2004

The interfacial layer between the oxide film and the metal film according to RTP annealing temperature of metal film has been studied. Two types of oxides, BPSG and PETEOS, were used as a bottom layer under multi-layered metal films. We observed the interface between oxide and metal films using SEM (scanning electron microscopy), TEM (transmission electron microscopy), AES (auger electron spectroscopy). Bonding failure was occurred by interfacial reaction between the BPSG oxide and the multi-layered metal films above $650^{\circ}C$ RTP anneal. The phosphorus accumulation layer was observed at interface between BPSG oxide and metal films by AES and TEM measurements. On the other hand, bonding was always good in the sample using PETEOS oxide as a bottom layer. We have known that adhesion between BPSG and multi-layered metal films was improved when the sample was annealed below $650^{\circ}C$.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.715-719
• /
• 2009

The phase change electrode board for the bio-information detection through electrical property response of phase change material was developed in this study. We manufactured the electrode board using Aluminum first that is widely used in conventional semiconductor device process. Without further treatment, these aluminum electrodes tend to contain voids in PETEOS(plasma enhanced tetraethyoxysilane) material that are easily detected by cross-sectional SEM(Scanning Electron Microscope). The voids can be easily attacked and transformed into holes in between PETEOS and electrodes after etch back and washing process. In order to resolve this issue of Al electrode board, we developed a electrode board manufacturing method using low resistivity TiN, which has advantages in terms of the step-coverage of phase change($Ge_2Sb_2Te_5$, GST) thin film as well as thermodynamic stability, without etch back and washing process. This TiN material serves as the top and bottom electrode in PRAM(Phase-change Random Access Memory). The good connection between the TiN electrode and GST thin film was confirmed by observing the cross-section of TiN electrode board using SEM. The resistances of amorphous and crystalline GST thin film on TiN electrodes were also measured, and 1000 times difference between the amorphous and crystalline resistance of GST thin film was obtained, which is well enough for the signal detection.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.61-61
• /
• 2003

CMP(Chemical Mechanical Polishing)는 VLSI의 제조공정에서 실리콘웨이퍼의 절연막내에 있는 토포그래피를 제어할 수 있는 광역 평탄화 기술이다. 또한 최근에는 실리콘웨이퍼의 나노토포그래피(Nanotopography)가 STI의 CMP 공정에서 연마 후 필름의 막 두께 변화에 많은 영향을 미치게 됨으로 중요한 요인으로 대두되고 있다. STI CMP에 사용되는 CeO$_2$ 슬러리에서 첨가되는 계면활성제의 농도에 따라서 나노토포그래피에 미치는 영향을 제어하는 것이 필수적 과제로 등장하고 있다. 본 연구에서는 STI CMP 공정에서 사용되는 CeO$_2$ 슬러리에서 계면활성제의 농도에 따른 나노토포그래피의 의존성에 대해서 연구하였다. 실험은 8 "단면연마 실리콘웨이퍼로 PETEOS 7000$\AA$이 증착 된 것을 사용하였으며, 연마 시간에 따른 나노토포그래피 의존성을 알아보기 위해 연마 깊이는 3000$\AA$으로 일정하게 맞췄다. 그리고 CMP 공정은 Strasbaugh 6EC를 사용하였으며, 패드는 IC1000/SUBA4(Rodel)이다. 그리고 연마시 적용된 압력은 4psi(Pounds per Square Inch), 헤드와 정반(table)의 회전속도는 각각 70rpm이다 슬러리는 A, B 모두 CeO$_2$ 슬러리로 입자크기가 다른 것을 사용하였고, 농도를 달리한 계면활성제가 첨가되었다. CMP 전 후 웨이퍼의 막 두께 측정은 Nanospec 180(Nanometrics)과 spectroscopic ellipsometer (MOSS-ES4G, SOPRA)가 사용되었다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.63-63
• /
• 2003

The nanotopography of silicon wafers has emerged as an important factor in the STI process since it affects the post-CMP thickness deviation (OTD) of dielectric films. Ceria slurry with surfactant is widely applied to STI-CMP as it offers high oxide-to-nitride removal selectivity. Aiming to control the nanotopography impact through ceria slurry characteristics, we examhed the effect of surfactant concentration and abrasive size on the nanotopography impact. The ceria slurries for this study were produced with cerium carbonate as the starting material. Four kinds of slurry with different size of abrasives were prepared through a mechanical treatment The averaged abrasive size for each slurry varied from 70 nm to 290 nm. An anionic organic surfactant was added with the concentration from 0 to 0.8 wt %. We prepared commercial 8 inch silicon wafers. Oxide Shu were deposited using the plasma-enhanced tetra-ethyl-ortho-silicate (PETEOS) method, The films on wafers were polished on a Strasbaugh 6EC. Film thickness before and after CMP was measured with a spectroscopic ellipsometer, ES4G (SOPRA). The nanotopogrphy height of the wafer was measured with an optical interferometer, NanoMapper (ADE Phase Shift)

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.26-29
• /
• 2004

High density plasma fluorinated silicate glass (HDP FSG) is used as a gap fill film for metal-to-metal space because of many advantages. However, FSG films can cause critical problems such as bonding issue of top metal at package, metal contamination, metal peel-off, and so on. It is known that these problems are caused by fluorine penetration out of FSG film. To prevent it, FSG capping layers such like SRO (Silicon Rich Oxide) are needed. In this study, their characteristics and a capability to block fluorine penetration for various FSG capping layers are investigated. Normal stress and High stress due to denser film. While heat treatment to PETEOS caused lower blocking against fluorine penetration, it had insignificant effect on SiN. Compared with other layers, SRO using ARC chamber and SiN were shown a better performance to block fluorine penetration.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.3
• /
• pp.24-27
• /
• 2001

The end point of oxide chemical mechanical polishing (CMP) have determined by polishing time calculated from removal rate and target thickness of oxide. This study is about control of oxide removal amounts on the shallow trench isolation (STI) patterned wafers using removal rate and thickness of blanket (non-patterned) wafers. At first, it was investigated the removal properties of PETEOS blanket wafers, and then it was compared with the removal properties and the planarization (step height) as a function of polishing time of the specific STI patterned wafers. We found that there is a relationship between the oxide removal amounts of blanket and patterned wafers. We analyzed this relationship, and the post CMP thickness of patterned wafers could be controlled by removal rate and removal target thickness of blanket wafers. As the result of correlation analysis, we confirmed that there was the strong correlation between patterned and blanket wafer (correlation factor: 0.7109). So, we could confirm the repeatability as applying for STI CMP process from the obtained linear formula. As the result of repeatability test, the differences of calculated polishing time and actual polishing time was about 3.48 seconds. If this time is converted into the thickness, then it is from 104 $\AA$ to 167 $\AA$. It is possible to be ignored because process margin is about 1800 $\AA$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.545-545
• /
• 2008

Poly-Si is an essential material for floating gate in NAND Flash memory. To fabricate this material within region of floating gate, chemical mechanical polishing (CMP) is commonly used process for manufacturing NAND flash memory. We use colloidal silica abrasive with alkaline agent, polymeric additive and organic surfactant to obtain high Poly-Si to SiO2 film selectivity and reduce surface defect in Poly-Si CMP. We already studied about the effects of alkaline agent and polymeric additive. But the effect of organic surfactant in Poly-Si CMP is not clearly defined. So we will examine the function of organic surfactant in Poly-Si CMP with concentration separation test. We expect that surface roughness will be improved with the addition of organic surfactant as the case of wafering CMP. Poly-Si wafer are deposited by low pressure chemical vapor deposition (LPCVD) and oxide film are prepared by the method of plasma-enhanced tetra ethyl ortho silicate (PETEOS). The polishing test will be performed by a Strasbaugh 6EC polisher with an IC1000/Suba IV stacked pad and the pad will be conditioned by ex situ diamond disk. And the thickness difference of wafer between before and after polishing test will be measured by Ellipsometer and Nanospec. The roughness of Poly-Si film will be analyzed by atomic force microscope.

• Applied Chemistry for Engineering
• /
• v.22 no.6
• /
• pp.631-635
• /
• 2011

Spherical and non-spherical silica particles prepared by the direct oxidation were studied for the effect of the particle size and shape of these particles on oxide CMP removal rate. Spherical silica particles, which have 10~100 nm in size, were prepared by the direct oxidation process from silicon in the presence of alkali catalyst. The 10 nm silica particles were aggregated by addition of an acid, an alcohol, or a silane as an aggregation inducer between the particles. Two or more aggregated silica particles were used as a seed to grow non spherical silica particles in the direct oxidation process of silicon in the presence of alkali catalyst. The oxide removal rate of spherical silica particles increased with increasing an average particle size for spherical silica abrasives in the oxide CMP. It further increased non-spherical particles, compared with the spherical particles in the similar average particle size.