• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.80-83
• /
• 2000

The post-annealing treatments on rf magnetron sputtered PZT($Pb_{1.05}(Zr_{0.52},\;Ti_{0.48})O_3$) thin films($4000{\AA}$) have been investigated for a structure of PZT/Pt/Ti/Coming glass(1737). Crystallization properties of PZT films were strongly dependent on RTA(Rapid Thermal Annealing) annealing temperature and time. We were able to obtain a perovskite structure of PZT at $650^{\circ}C$ and 10min. P-E curves of Pd/PZT/Pt capacitor demonstrate typical hysteresis loops. The measured values of $P_r$, $E_c$ were $8.1[{\mu}C/cm^2]$, 95[kV/cm] respectively. Polarization value decrease about 25% after $10^9$ cycles.

• 한국전기전자재료학회논문지
• /
• 제21권12호
• /
• pp.1077-1082
• /
• 2008

To fabricate a multi-layered piezoelectrics/electrodes structure, the piezoelectrics should be sintered at the temperature lower than $950^{\circ}C$ to use the silver electrode, which is cheaper than the electrodes containing noble metals such as Pd and Pt. Therefore, in this study, we modified the composition of $Pb(Zr,Ti)O_3$-based material as $(Pb_{0.98}Cd_{0.02})(Ni_{1/3}Nb_{2/3})_{0.25}Zr_{0.35}Ti_{0.4}O_3$ to lower the sintering temperature and to improve the piezoelectric properties. Small amount of $MnCO_3$, $SiO_2$, and $Pb_3O_4$ were also added to lower the sintering temperature of the ceramic. The prepared raw powders were mixed by using a ball mill for 24 hours. And then the mixed powders were calcinated for 2 hours at $800^{\circ}C$. The calcinated powders were again crushed with the ball mill for 72 hours. The final powders were pressed for making the shape of ${\emptyset}15\;mm$ disk. The disk-type samples were sintered at temperature range of $850{\sim}950^{\circ}C$. The crystal phases of the sintered specimens were perovskite structure without secondary phases. All of the measured electrical properties such as electromechanical coupling coefficients ($k_p$), mechanical quality factors ($Q_m$), and piezoelectric charge constants ($d_{33}$) were decreased with decreasing the sintering temperatures. The electrical properties measured at the sample sintered at $950^{\circ}C$ were 54% of $k_p$, 503 of $Q_m$, and 390 pC/N of $d_{33}$, respectively. These properties were considered to be fairly good for the application of multi-layered piezoelectric generators or actuators.

• 한국방재학회 논문집
• /
• 제11권2호
• /
• pp.179-183
• /
• 2011

본 연구에서는 광 반응기 내부의 영향반경을 평가하기 위해 자외선(UV-C) 램프의 강도와 photochemical에 의한 OH 라디칼 생성량을 측정하였다. 또한 $TiO_2$ (Degussa P-25)를 농도별로 첨가하여 자외선 램프의 영향반경을 측정하였다. 광 반응기는 아크릴 재질의 bath 타입을 사용하였고, 254 nm의 파장을 가진 UV-C 자외선 램프를(SANKYO DENKI, 지름 : 2.2 cm, 길이 : 18.5 cm) 사용하였다. 램프의 소비전력은 10.5 W이고, OH 라디칼 생성량을 측정하기 위해 KI dosimetry를 사용하였다. 실험 결과로부터 광 반응기에서 자외선의 강도가 0.367 mW/$cm^2$이상 조사되어야하고, 거리는 13 cm 이내에서 OH 라디칼 생성에 영향을 미치는 것으로 나타났다. 또한 광촉매 반응기에서는 촉매의 농도로 인해 자외선의 영향반경이 매우 감소하는 것을 확인할 수 있었다.

• Rapid Communication in Photoscience
• /
• 제2권2호
• /
• pp.64-66
• /
• 2013

Photoreduction of $CO_2$ into hydrocarbon fuels on the surface of photocatalyst is one of the breakthroughs in the field of photocatalysis. At present various approaches have been investigated with the aim of increasing the $CO_2$ conversion efficiency. The reactor for photoconversion of $CO_2$ plays a vital role in experimental setup. In this work an attempt was made to testify a newly designed the photoreactor for conversion of $CO_2$ into useful products. The photoreactor was specifically designed for simple operation bearing features of temperature and pressure control. The reactor has been tested successively with the standard titania, Degussa P25 yielding methane with moderate production rate of 30.8 $ppm{\cdot}g^{-1}{\cdot}h^{-1}$ under UV lamp with 365 nm wavelength. The methane yield obtained is comparable to the values reported in literature. Thus we anticipate that this experimental setup equipped with newly designed photoreactor can yield competitive amounts of fuels from $CO_2$ photoredcution via 365 nm UV light illumination on various photocatalysts.

• 대한치과보철학회지
• /
• 제45권5호
• /
• pp.601-610
• /
• 2007

Statement of problem: The adhesion between titanium and ceramic is less optimal than conventional metal-ceramic bonding, due to reaction layer form on cast titanium surface during porcelain firing. Purpose: This study characterized the effect of titanium-ceramic adhesion after gold and TiN coating on cast and wrought titanium substrates. Material and method: Six groups of ASTM grade II commercially pure titanium and cast titanium specimens$(13mm{\times}13mm{\times}1mm)$ were prepared(n=8). The conventional Au-Pd-In alloy served as the control. All specimens were sandblasted with $110{\mu}m\;Al_2O_3$ particles and ultrasonically cleaned for 5min in deionized water and dried in air before porcelain firing. An ultra-low-fusing dental porcelain (Vita Titankeramik) was fused on titanium surfaces. Porcelain was debonded by a biaxial flexure test at a cross head speed of 0.25mm/min. The excellent titanium-ceramic adherence was exhibited by the presence of a dentin porcelain layer on the specimen surface after the biaxial flexure test. Area fraction of adherent porcelain (AFAP) was determined by SEM/EDS. Numerical results were statistically analyzed by one-way ANOVA and Student-Newman-Keuls test at ${\alpha}=0.05$. Results: The AFAP value of cast titanium was greatest in the group 2 with TiN coating, followed by group 1 with Au coating and the group 3 with $Al_2O_3$ sandblasting. Significant statistical difference was found between the group 1, 2 and the group 3 (p<.05). The AFAP value of wrought titanium was greatest in the group 5 with TiN coating, followed by the group 4 with Au coating and the group 6 with $Al_2O_3$ sandblasting. Conclusion: No significant difference was observed among the three groups (p>.05). The AFAP values of the cast titanium and the wrought titanium were similar. However the group treated with $Al_2O_3$ sandblasting showed significantly lower value (p<.05).

• Advances in environmental research
• /
• 제4권1호
• /
• pp.25-38
• /
• 2015

Wastewaters of textile industry cause high volume colour and harmful substance pollutions. Photocatalytic degradation is a method which gives opportunity of reduction of organic pollutants such as dye containing wastewaters. In this study, photocatalytic degradation of C.I. Basic Yellow 28 (BY28) as a model dye contaminant was carried out using Degussa P25 in a photocatalytic reactor. The experiments were followed out at three different azo dye concentrations in a reactor equipped UV-A lamp (365 nm) as a light source. Azo dye removal efficiencies were examined with total organic carbon and UV-vis measurements. As a result of experiments, maximum degradation efficiency was obtained as 100% at BY28 concentration of $50mgL^{-1}$ for the reaction time of 2.5 h. The photodegradation of BY28 was described by a pseudo-first-order kinetic model modified with the langmuir-Hinshelwood mechanism. The adsorption equilibrium constant and the rate constant of the surface reaction were calculated as $K_{dye}=6.689{\cdot}10^{-2}L\;mg^{-1}$ and $k_c=0.599mg\;L^{-1}min^{-1}$, respectively.

• 한국물환경학회지
• /
• 제28권1호
• /
• pp.115-120
• /
• 2012

Different colloidal particles generally co-exist in the water and wastewater. Thus, there needs to identify practical electrokinetic characteristics of the particles, comparing with the case when each colloidal material is independently distributed. In this study, changes of overall zeta potential was examined through mixed dispersions of $TiO_{2}$ and $MnO_{2}$. The mixing ratios were classified into 3-type in order to distinguish the effects of the proportions of each particle from those of total concentration in colloidal suspensions. The types are single colloidal dispersions of $TiO_{2}$ and $MnO_{2}$ (1:0, 0:1), mixed dispersions at different ratios (0.75:0.25, 0.5:0.5, 0.25:0.75), and a mixed dispersion with doubled concentration (1:1), respectively. It showed that the overall variation of zeta potential as a function of pH was intensified in a colloidal dispersion with the ratio of 1:1. It was concerned that the double action of ion would contribute to this result. On the one hand, the zeta potentials of each colloidal dispersion commonly decreased at the state of strong acid and base under the influence of compression of the electric double layer. The changing patterns were also considered through calculating total interaction energy between colloidal particles based on DLVO theory and measuring turbidity of the colloidal dispersions.

• Bulletin of the Korean Chemical Society
• /
• 제35권10호
• /
• pp.2935-2940
• /
• 2014

Monodispersed $Bi_2O_2CO_3$ nanoplates with an average width of 320 nm and thicknesses of 50-90 nm were successfully synthesized by a simple solvothermal method in a mixture solution of polyethylene glycol and $H_2O$. The obtained nanoplates were characterized by means of XRD, FT-IR, SEM and TEM. The effect of surfactant sodium dodecyl benzene sulfonate on the morphology of $Bi_2O_2CO_3$ product was investigated. Under simulated solar light irradiation, $Bi_2O_2CO_3$ nanoplates exhibited superior photocatalytic activities towards the degradation of RhB as well as high chemical stability upon cycling photocatalytic test. The nanoplates also showed promising photodegradation ability for eliminating refractory pollutant of phenol. The excellent photocatalytic performance of $Bi_2O_2CO_3$ nanoplates as compared with P25-$TiO_2$ endows them as promising high efficiency photocatalysts.

• 자원환경지질
• /
• 제40권6호
• /
• pp.727-738
• /
• 2007

운봉지역 하상퇴적물에 대한 지구화학적 특성규명을 통해, 주성분원소 및 미량원소에 대한 자연 배경치를 제시하고, 그 기반암(압쇄상화강암, Kim et al., 1992)과의 비교를 통해 지구화학적 재해에 대해 예견하고자 한다. 73개의 하상퇴적 물시료를 물이 흐르고 있는 1차 수계를 대상으로 채취하였고, XRD, XRF ICP-AES, NAA를 이용하여 주성분원소 및 미량성분원소를 분석하였다. 운봉지역의 주성분원소 함량은 $SiO_2\;36.94{\sim}65.39 wt.%,\;Al_2O_3\;10.15{\sim}21.77wt.%,\;Fe_2O_3\;3.17{\sim}10.90wt.%,\;CaO\;0.55{\sim}5.27wt.%,\;MgO\;0.52{\sim}4.94wt.%,\;K_2O\;1.38{\sim}4.54wt.%,\;Na_2O\;0.49{\sim}3.36wt.%,\;TiO_2\;0.39{\sim}1.27wt.%,\;MnO\;0.04{\sim}0.22wt.%,\;P_2O_5\;0.08{\sim}0.54wt.%$의 범위를 보이며, 미량성분 및 희토류원소 함량은, $Cu\;4.8{\sim}134ppm,\;Pb\;24.2{\sim}82.5ppm,\;Sr\;95.9{\sim}739ppm,\;V\;19.9{\sim}124ppm,\;Zr\;52.9{\sim}145ppm,\;Li\;25.2{\sim}3.3ppm,\;Co\;3.87{\sim}50.0ppm,\;Cr\;17.4{\sim}234ppm,\;Hf\;3.93{\sim}25.2ppm,\;Sc\;4.60{\sim}20.6ppm,\;Th\;3.82{\sim}36.9ppm,\;Ce\;45.7{\sim}243ppm,\;Eu\;0.89{\sim}2.69ppm,\;Yb\;1.42{\sim}5.18ppm$의 범위를 보인다. 주성분원소의 함량비교에서 CaO, $Na_2O,\;K_2O$ 함량은 하상퇴적물에서 기반암(압쇄상화강암류, Kim et al., 1992)인 압쇄상화강암류보다 높게 나타난다. 그리고 $Al_2O_3$와 $SiO_2$는 하상퇴적물과 기반암(압쇄상화강암류, Kim et al., 1992) 모두에서 높은 상관관계를 보인다. 하상퇴적물에서는 $SiO_2$ 함량이 높아질수록 희토류원소 함량도 같이 증가하는 특징을 보이나, 압쇄상화강암류에서는 $SiO_2$ 함량이 높아질수록 희토류원소 함량은 감소하는 특징을 보인다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.61-66
• /
• 2003

In this paper, the effect of binder additive on the fracture toughness was metal matrix composite produced by squeeze casting method. In this study using the matrix is AC4CH and reinforcement used Aluminum borate whisker. Each MMC was produced by add inanimate binder ($SiO_2,\;Al2O_3,\;TiO_2$) to whiskers for increase the binding together of whiskers. Fracture toughness test were carry out in accordance with the ASTM E-399 standard test method, W=25mm, b=12.5mm CT(half size) specimen. However Base metal AC4CH was not meet the qualification of $P_m/P_Q<1.1$, so that test were performed $J_{IC}$ test. $K_{J_{IC}}$ value was measuring by $J_{IC}$ value change into $K_{IC}$. $J_{IC}$ test was carry out in accordance with the ASTM 1820.