• Journal of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.61-63
• /
• 1962

The polarographic behaviors of Tl(I) was investigated in EDTA and NTA as supporting electrolytes for determination of Tl(I). A base solution containing 0.005 % gelatine, 0.1 M EDTA, and 0.05 M NTA was used. The halfwave potential of Tl(I) determined is -0.495 V v.s. S.C.E. in 0.1 M EDTA at pH 4.1 and -0.520V v.s. S.C.E. in 0.05 M NTA at pH 6.3. In this paper, the effects of gelatine concentration and pH values was investigated. The half-wave potentials of common elements was determined and compared with the half-wave potential of Tl(I).

• Elastomers and Composites
• /
• v.43 no.1
• /
• pp.18-24
• /
• 2008

An oligomeric diol was utilized as a modifier for the reaction rate and mechanical properties of a RT-castable polyurethane elastomer. Both the reaction rate and the tensile strength of the blend samples, in which the modifier and the base resins were mixed with one-shot method, showed an exponential decrease as the increase of modifier concentration. Thermal analysis method of Kissinger was also effectively applied in the present study, showing good linearity in the plot of ln $(q/T^2_p)$ vs. $(1/T_p)$ and activation energy $E_a$ of 44.80 kJ/mol, which is similar to the general castable polyurethane. In the mechanical properties, remarkable decrease of strength was found by the addition of modifier concentration range up to about 20 phr, while characteristic elongation property of the elastomer, high elongation at lower strength, was observed over 20 phr of the modifier. Exponential decrease of the break strength of the blend sample exhibited that the mechanical properties of the blend might be considerably sensitive to the modifier concentration.

• Korean Journal of Materials Research
• /
• v.30 no.10
• /
• pp.509-514
• /
• 2020

The two key variables of an Si solar cell, i.e., emitter (n-type window layer) and base (p-type substrate) doping levels or concentrations, are studied using Medici, a 2-dimensional semiconductor device simulation tool. The substrate is p-type and 150 ㎛ thick, the pn junction is 2 ㎛ from the front surface, and the cell is lit on the front surface. The doping concentration ranges from 1 × 10¹⁰ cm^-3 to 1 × 10²⁰ cm^-3 for both emitter and base, resulting in a matrix of 11 by 11 or a total of 121 data points. With respect to increasing donor concentration (Nd) in the emitter, the open-circuit voltage (Voc) is little affected throughout, and the short-circuit current (Isc) is affected only at a very high levels of Nd, exceeding 1 × 10¹⁹ cm^-3, dropping abruptly by about 12%, i.e., from Isc = 6.05 × 10^-9 A·㎛^-1, at Nd = 1 × 10¹⁹ cm^-3 to Isc = 5.35 × 10^-9 A·㎛^-1 at Nd = 1 × 10²⁰ cm^-3, likely due to minority-carrier, or hole, recombination at the very high doping level. With respect to increasing acceptor concentration (Na) in the base, Isc is little affected throughout, but Voc increases steadily, i.e, from Voc = 0.29 V at Na = 1 × 10¹² cm^-3 to 0.69 V at Na = 1 × 10¹⁸ cm^-3. On average, with an order increase in Na, Voc increases by about 0.07 V, likely due to narrowing of the depletion layer and lowering of the carrier recombination at the pn junction. At the maximum output power (Pmax), a peak value of 3.25 × 10^-2 W·cm^-2 or 32.5 mW·cm^-2 is observed at the doping combination of Nd = 1 × 10¹⁹ cm^-3, a level at which Si is degenerate (being metal-like), and Na = 1 × 10¹⁷ cm^-3, and minimum values of near zero are observed at very low levels of Nd ≤ 1 × 10¹³ cm^-3. This wide variation in Pmax, even within a given kind of solar cell, indicates that selecting an optimal combination of donor and acceptor doping concentrations is likely most important in solar cell engineering.

• The Korean Journal of Physiology
• /
• v.16 no.1
• /
• pp.13-23
• /
• 1982

Effects of external pH and potassium concentrations on the electrical and mechanical properties were investigated on rabbit papillary muscle. Papillary muscles were perfused in horizontal chamber with Tris Tyrode solutions and action potential along with isometric tension was recorded simultaneously. Potassium concentrations were varied between 1 and 12 mM at low(6.9), normal(7.4) and high (7.9) external pH. The following results were obtained: 1) On rasing the potassium concentration from 1 to 12 mM resting membrane potentials decreased from $-88.8{\pm}2.8$ to $-66.4{\pm}1.2\;mV$ at normal pH and the amplitude of action potential decreased from $115.1{\pm}0.7$ to $97.5{\pm}2.8\;mV$. On lowering the potassium concentration, membrane hyperpolarized and at 1 mM potassium concentration resting potentials were $-107{\pm}2.2\;mV$. Duration of action potential especially $APD_{60}{\sim}APD_{90}$ increased($APD_{90}$: $214{\pm}15.8\;ms$ at 1 mM $K^+$ to $287{\pm}18.1\;ms$ at 12 mM $K^+$). 2) During acidosis membranes hyperpolarized by more than 20 mV within 1 min. and then slow recovery was observed during the following 10 min. During alkalosis membranes depolarized about 10 mV, which were maintained until washing with normal Tyrode solutions. 3) On lowering the external pH(7.9-6.5), duration of action potential increased progressively and it was most prominent at pH 6.5 and $K^+$ 1mM. 4) Magnitude of developed tension was $0.6{\pm}0.14\;g/mm^2$ at normal pH and potassium concentration (stimulus frequency : 60/min). Relative isometric tension to normal value increased along the increment of stimulus frequency($44.2{\pm}4.2%$ at 6/min to $271{\pm}86.7%$ at 180/min). Force-frequency relations were altered quantitatively during the perfusion with different external pH solutions. 5) Developed tension did not show marked variation within the range of $2{\sim}8\;mM$ potassium concentrations. Positive inotropism was observed at less than 2 mM $K^+$ and negative inotropism beyond 12 mM $K^+$ concentrations. From the above results we concluded that the effects of potassium ion concentration on electrical and mechanical properties of rabbit papillary muscle are related to the changes in surface negative charge due to acid base disturbances.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.38-38
• /
• 2009

Wafer thickness of crystalline silicon is an important factor which decides a price of solar cell. PC1D was used to fix a condition that is required to get a high efficiency in a crystalline silicon solar cell using thin wafer($150{\mu}m$). In this simulation, base resistivity and emitter doping concentration were used as variables. As a result of the simulation, $V_{oc}$=0.6338(V), $I_{sc}$=5.565(A), $P_{max}$=2.674(W), FF=0.76 and efficiency 17.516(%) were obtained when emitter doping concentration is $5{\times}10^{20}cm^{-3}$, depth factor is 0.04 and sheet resistance is $79.76{\Omega}/square$.

• Membrane and Water Treatment
• /
• v.5 no.4
• /
• pp.251-263
• /
• 2014

The study contributes in the treatment of waste generated by the textile complex cotton of Draa Ben Khedda, Algeria. The azo dye "Direct Red Solophenyle 4GE" represents the base particle of the discharges and electrocoagulation with nanofiltration are used as a means of treatment. The solar photovoltaic is suitable for electrochemical process to reduce the energy cost. Several study parameters are considered in this work. The electrocoagulation batch gives the best reduction 37% for a dye concentration of 7.21 mg/L ($[NaCl]_{added}$=1g/L; $j=25.2mA/cm^2$). Coupling methods (electrocoagulation-nonofiltration) gives a complete discoloration rejecting concentration 52.4 mg/L (pHi = 7.6, $[NaCl]_{added}$=3g/L, $j=2.13mA/cm^2$). The result shows the coupling efficiency with a reduced amount of resulting slurry at the end of treatment.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.36 no.3
• /
• pp.377-384
• /
• 2009

The purpose of this study is to investigate the residual fluoride concentration of fluoride tape in oral cavity which made by spraying NaF on carboxymethylcellulose base. After 1, 3, 5, 7 hours and 1, 2, 3 days of applicating APF gel(60seconds $taste^{(R)}$, 1.23% APF gel, Group I), Fluoride varnish($CavityShield^{TM}$, 5% NaF, Group II) and Fluoride tape(SCMC-T-5, 5% NaF, Trial product, Group III) in oral cavity of 27 healthy adults in their twenties, the result of fluoride concentration in unstimulated whole saliva which measured by using fluoride sensitive electrode made up to following conclusion. 1. Until 7 hours after application in every group, it showed significantly higher fluoride concentration in saliva than baseline value but at 1, 2, 3 days after application, there were no significant differences between measurements and baseline value(p>0.05). 2. Until 7 hours after application at every time, mean fluoride concentration in saliva was higher in the order of Group II, I and III. 3. 1 hour and 3 hours after application, Group II revealed significantly higher fluoride concentration than Group III(p<0.05), but there were no significant differences between Group Ⅰ and Group III in every time.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3A
• /
• pp.207-212
• /
• 1999

Undoped InP epilayers with high purity were grown by using $In/PCl_3/H_2$ chloride vapor phase epitaxy. It was found that the growth of InP homoepitaxial layer is optimized at the growth temperature of $630^{\circ}C$ and at the $PCl_3$ molar fraction of $1.2\times10^{-2}$. The carrier concentration of InP epilayer was less than $10^{14} {cm}^{-3}$ from the low temperature (11K) photoluminescence measurement. Growth behavior of undoped InP current blocking layer on reactive ion-etched (RIE) mesas has been investigated for the realization of 1.55 $\mu \textrm m$buried-heterostructure laser diode (BH LD), using chloride vapor phase epitaxy. On the base of InP homoepitaxy, InP current blocking layers were grown at the growth temperatures ranging from $620^{\circ}C$ to $640^{\circ}C$. Almost planar grown surfaces without edge overgrowth were achieved as the growth temperature increased. It implied that higher temperature enhanced the surface diffusion of the growth species on the {111} B planes and suppressed edge overgrowth.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.101-107
• /
• 2003

Since stainless steel sheets have good mechanical properties, weldability, appearance and corrosion resistance, they are commonly used as one of the structural materials of the railroad cars or the commercial vehicles which are manufactured by the spat welding. Among the many kinds of spot welded lap joints, it can be found that multi-lap joints are employed in their body structure. But, fatigue strength of these joints is lower than that of base metal due to high stress concentration at the nugget edge of spot weld and is considerably influenced by welding conditions as well as the mechanical and geometrical factors. Thus, it is necessary to establish a reasonable and systematic design criterion for the long life design of the spot-welded body structures. In this paper, the stress distribution and deformation around the spot-welded multi-lap joints subjected to tensile shear load was numerically analyzed. Also, the $\Delta$P-Nf curve was obtained by fatigue tests. Using these results, $\Delta$P-Nf curves were rearranged in to the ${\Delta}{\sigma}$-Nf relation with the maximum stress at nugget edge of spot weld.

• KSBB Journal
• /
• v.23 no.6
• /
• pp.504-508
• /
• 2008

The objectives of this study were to develope the economical process for bioethanol production from domestic triticale and investigate optimal fermentation conditions such as temperature, time, and enzyme concentration used to pre-treatment process. Triticale mash, containing 148 g of total sugar per 1 L of mash, was fermented with Saccharomyces cerevisiae CHY1011 at $33^{\circ}C$. Fermentation of mash supplemented with enzyme was completed within 48-60 hours, and the ethanol yield was 410.9 L/tonne of dry base. On the other hand, fermentation of mash without enzyme addition was completed within 36-48 hours, but the ethanol yield was 342.2 L/tonne of dry base. For optimal bioethanol production from triticale, viscosity reduction enzyme was added in the pre-treatment process, and the fermentation rate of triticale was 92.0-94.2%. In addition, the results showed that bioethanol production of triticale by low-temperature pre-treatment would provide higher ethanol production efficiency and lower operating costs.