• Journal of the Korean Society for Railway
• /
• v.7 no.1
• /
• pp.55-59
• /
• 2004

Composite materials were used widely due to merit of light weight, low maintenance cost and easy installation. But it is the cause of enormous casualties to men and properties because of weak about the fire. Particularly, it is more serious in case of subway train installed composite materials. For this reason, experimental comparison has been done fur measuring heat release rate(H.R.R) and smoke production rate(S.P.R) of interior panels of electric motor car using cone calorimeter. A high radiative heat flux of 50kW/㎡ was used to bum out all materials and to simulate the condition of fully developed fire case in the tests. It was observed that Heat Release Rate and Smoke Production Rate curves were dependent on the kinds of the interior materials. From the heat release rate curves, the sustained ignition time, peak heat release rate and total heat release rate were deduced, These data are useful in classifying the materials by calculating two parameters describing the possibility to flashover.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.539-545
• /
• 2000

This paper describes the design method of the magnetic system to maximize the magnetic flux leakage (MFL) in non-destructive testing (NDT) system. The defect signals in MFL type NDT system mainly depends on the change of the magnetic leakage flux in the region of defect. The characteristics of the B-H curves are analyzed and the design method to define the operating point in B-H curves for the maximum leakage is performed. The computed MFL signal by nonlinear finite element method is verified by measurement using Hall sensors mounted on the 6 legs PIG in the 8 inches test tube with defects. The rhombic defects could be successfully composed from the defect signals.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.12
• /
• pp.91-100
• /
• 2019

Hollow prestressed concrete-filled steel tube (HCFT) piles, which combines PHC piles inside thin-wall steel tubes, were developed to increase the flexural strength of the pile with respect to the lateral load. Since P-M curves are needed for evaluating the structural safety of piles when applying HCFT piles to fields, equations for plotting P-M curves of HCFT piles in limit states were proposed. When the yield strength is applied to the steel tube and PC steel bar of HCFT piles, the proposed equations significantly underestimated the flexural strength of HCFT piles. Unlike the flexural strength test results, the proposed equations also provide greater flexural strengths for 12 mm thick steel pipe piles with the same diameter than for HCFT piles. However, when the ultimate strengths are used instead of the yield strengths for the steel tube and PC steel bar, the proposed equations provide the flexural strengths very close to the flexural strength test results.

• Communications for Statistical Applications and Methods
• /
• v.16 no.1
• /
• pp.185-193
• /
• 2009

Machine learning methods such as support vector machines and random forests yield nonparametric prediction functions of the form y = $f(x_1,{\ldots},x_p)$. As a sequel to the previous article (Huh and Lee, 2008) for visualizing nonparametric functions, I propose more sensible graphs for visualizing y = $f(x_1,{\ldots},x_p)$ herein which has two clear advantages over the previous simple graphs. New graphs will show a small number of prototype curves of $f(x_1,{\ldots},x_{j-1},x_j,x_{j+1}{\ldots},x_p)$, revealing statistically plausible portion over the interval of $x_j$ which changes with ($x_1,{\ldots},x_{j-1},x_{j+1},{\ldots},x_p$). To complement the visual display, matching importance measures for each of p predictor variables are produced. The proposed graphs and importance measures are validated in simulated settings and demonstrated for an environmental study.

• ALGAE
• /
• v.19 no.3
• /
• pp.207-216
• /
• 2004

Characteristics of photosynthesis-light and photosynthesis-temperature relationships were seasonally compared among 4 species, two temperate Sargassurn (S. ringgoldianum and S. spathulophyllum) and two temperate kelp (Ecklonia cava and Eisenia bicyclis), growing in the same habitat in Oura Bay, Shimoda, central Japan. The photosynthesis-irradiance (P-I) curve of each species at the in situ temperature and the photosynthesis-temperature (P-T) curve at near saturation irradiance (400μmol·m^(-2)·s^(-1)) were determined by using differential gas-volumeters. Maximum photosynthetic rates (Prnax) for P-I curves of the two Sargassurn species were higher from summer to autumn than from winter to spring, while those of the two kelp species showed little difference among seasons. Net photosynthetic rates (Pn) at 100-400μmol·m^(-2)·s^(-1) of the Sargassurn species were higher than those of the kelp species in autumn, spring and summer, while in winter the rates were about the same between the Sargassurn and kelp species. Among seasons, the light saturation index (1k) values, dark respiration rates and light compensation points of Sargassurn species differed more than those of kelp species. Optimum temperature for P-T curves of Sargassurn species was 29℃ and that of kelp species was 27℃ in summer, while in winter the former was 27℃ and the latter was 25℃. Pn at 400 μmol·m^(-2)·s^(-1) at 10-33℃ of Sargassurn species were considerably higher than those of kelp species from spring to summer, while from autumn to winter the rates at 5-27℃ were about the same between the two. At supra-optimum temperatures, Pn of kelp species decreased more sharply than those of Sargassurn species in each season. These facts indicate that the two temperate Sargassurn species have a higher potential photosynthetic performance under warmer conditions than the two temperate kelp species even though they grow in the same habitat.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.5
• /
• pp.561-565
• /
• 2010

Stainless steel sheets are widely used as structural materials for the manufacture of railroad cars and commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding. For the fatigue design of gas welded joints such as fillet joints and plug joints, it is necessary to obtain information on the stress distribution at the weldment and the fatigue strength of the gas welded joints. Moreover the influence of the geometrical parameters corresponding to the gas welded joints on the stress distribution and fatigue strength must be evaluated. ${\Delta}P-N_f$ curves were obtained from the data recorded in fatigue tests. Using these results, the ${\Delta}P-N_f$ curves were rearranged according the relation between $\Delta\sigma-N_f$ and the maximum stress at the edge of the fillet welded joint.

• Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.41-47
• /
• 2009

Column experiments were performed in this study to investigate humic acid adhesion to iron oxide-coated sand (ICS) under different experimental conditions including influent humic acid concentration, flow rate, solution pH, and ionic strength/composition. Breakthrough curves of humic acid were obtained by monitoring effluents, and then column capacity for humic acid adsorption ($C_cap$), total adsorption percent (R), and mass of humic acid adsorbed per unit mass of filter media ($q_a$) were quantified from these curves. Results showed that humic acid adhesion was about seven times higher in ICS than in quartz sand at given experimental conditions. This indicates that humic acid removal can be enhanced through the surface charge modification of quartz sand with iron oxide coating. The adhesion of humic acid in ICS was influenced by influent humic acid concentration. $C_cap$ and $q_a$ increased while R decreased with increasing influent humic acid concentration in ICS column. However, the influence of flow rate was not eminent in our experimental conditions. The humic acid adhesion was enhanced with increasing salt concentration of solution. $C_cap$, $q_a$ and R increased in ICS column with increasing salt concentration. On the adhesion of humic acid, the impact of CaCl2 was greater than that of NaCl. Also, the humic acid adhesion to ICS decreased with increasing solution pH. $C_cap$, $q_a$ and R decreased with increasing solution pH. This study demonstrates that humic acid concentration, salt concentration/composition, and solution pH should be controlled carefully in order to improve the ICS column performance for humic acid removal from water.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.2
• /
• pp.279-285
• /
• 1993

It is important to understand the interrelationship between adsorption, equilibrium and mass transport in efficient design and operation of the granular activated carbon(GAC) adsorption systems. In this study, the micro-diameter-depth adsorption system(MIDDAS) technique was developed to estimate equilibrium and mass transport parameters, which were utilized to simulate adsorption and mass transport phenomena dynamically and mathematically. The homogeneous surface diffusion model(HSDM) utilizing the estimated equilibrium and mass transport parameters including the film transfer coefficients and surface diffusivities from the MIDDAS technique, successfully predicted competitive adsorption, desorption and chromatographic displacement effects. In the binary solute system of p-chlorophenol(PCP) and p-nitrophenol(PNP), PCP was displaced by PNP and the HSDM could predict successfully. While the HSDM described the desorption breakthrough curves for PCP, PNP and PTS well when complete reversible adsorption was assumed, the desorption breakthrough curves for DBS could be predicted after subsequent incorporation of the degree of irreversibility into the model simulations.

• Journal of the Korean Geophysical Society
• /
• v.8 no.2
• /
• pp.67-74
• /
• 2005

Two-dimensional S-wave velocity sections from SH-wave refraction tomography and surface wave dispersions were obtained by inverting traveltimes of first arrivals and surface wave dispersions, respectively. For the purpose of comparison, a P-wave velocity tomogram was also obtained from a P-wave refraction profiling. P and Rayleigh waves generated by vertical blows on a plate with a sledgehammer were received by 100- and 4.5-Hz geophones, respectively. SH-waves generated by horizontal blows on both sides of a 50 kg timber were received by 8 Hz horizontal geophones. The shear-wave signals were enhanced subtracting data of left-side blows from ones of the right-side blows. Shear-wave velocities from tomography inversion of first-arrival times were compared with ones from inverting dispersion curves of Rayleigh waves. Although the two velocity sections look similar to each other in general, the one from the surface waves tends to have lower velocities. First arrival picking of SH waves is troublesome since P and PS-converted waves arrive earlier than SH waves. Application of the surface wave method, on the other hand, is limited where lateral variation of subsurface tructures is not mild.

• Journal of The Korean Astronomical Society
• /
• v.11 no.1
• /
• pp.31-36
• /
• 1978

Although Serkowski used a single value K=1.15 in representing all the observed interstellar linear polarization curves by his empirical relation $p({\lambda})/P_{max}$=exp (-K $1n^2({\lambda}_{max}/{\lambda})$), where $p_{max}$ is the maximum polarization at wavelength ${\lambda}_{max}$, we have noticed a meaningful variation in K from observations of 72 stars. By comparing K's with $P_{max}/E_{B-V}\;and\;with\;{\lambda}_{max}$, we have examined how the shape of the polarization curve is related with the degree of grain alignment on one hand, and with grain sizes on the other. We have shown that correlations between K, $P_{max}/E_{B-V}\;and\;with\;{\lambda}_{max}$, are consistent with the idea of Davis-Greenstein mechanism for grain alignment.