• Journal of Ginseng Research
• /
• 제8권1호
• /
• pp.38-44
• /
• 1984

In order to investigate the influence of gamma-irradiation on fatty acids in ginseng, ginseng were irradiated with various radiation doses(0-50 Mrads). The results are as follows. 1. With increasing dose, standard fatty acids were decreased in the order of linolenic acid, linoleic acid and oleic acid, and their contents in the presence of oxygen were decreased more t than that in the absence of oxygen. 2. Changes of lipid content in white ginseng by gamma irradiation were varied with the samples, but the changes of crude lipid and purified lipid in a sample were showed same fashion. 3. The fatty acid contents in white ginseng were decreased by gamma irradiation in the order of linolenic acid, linoleic acid, oleic acid, stearic acid and palmitic acid.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.130-131
• /
• 2005

In the era of submicron devices, super ultra thin gate oxide characteristics are required. Titanium silicide process has studied gate oxide reliability and dielectric strength characteristics as the composition of gate electrode. In this study the author observed process characteristics on MOS structure. In view point of the process characteristics of MOS capacitor, the oxygen & Ti, Si2 was analyzed by SIMS analysis on before and after annealing with 1,2 step silicidation, the Ti contents[Count/sec]of $9.5{\times}1018$ & $6.5{\times}1018$ on before and after 2'nd anneal. The oxygen contents[Count/sec] of $4.3{\times}104$ & $3.65{\times}104$, the Si contents[Count/sec] of $4.2{\times}104$ & $3.7{\times}104$ on before and after 2'nd anneal. The rms value[A] was 4.98, & 4.03 on before and after 2'nd anneal.

• 한국표면공학회지
• /
• 제42권5호
• /
• pp.220-226
• /
• 2009

Cr-O-N coatings having different oxygen contents were deposited on Si wafer and SUS 304 substrates by an arc ion plating technique using Cr target in $Ar/O_2/N_2$ gaseous atmosphere. As increasing oxygen content in the coating, the microstructure of Cr-O-N coating changed from polycrystalline having NaCl structure to amorphous structure. Further increase of oxygen content resulted in phase transformation from amorphous to rhombohedral structure. From the variations of d value and average grain size, it was revealed that the maximum solubility of oxygen in Cr-O-N coating was about 21 at.%. And the maximum micro-hardness of 2751HK was obtained in this composition. The lowest friction coefficient was measured in the coating having 34.8 at.% of oxygen. However, more narrow width of wear track was found in the coating having 30.1 at.% of oxygen.

• 대한인간공학회지
• /
• 제24권4호
• /
• pp.47-53
• /
• 2005

This study aim to investigate the effects of supply of oxygen enhances cerebral activation through increased activation in the brain and using a 3 Tesla fMRI system. Five volunteers (right handed, average age of 21.3) were selected as subjects for this study. Oxygen supply equipment that provides 30% oxygen at a constant rate of 15L/min was given using face mask. A 3 Tesla fMRI system using the EPI BOLD technique, and three-pulse sequence technique get of the true axial planes scanned brain images. The author can get the perfusion images of the brain by oxygen inhalation with susceptibility contrast EPI sequence at the volunteers. Complex movement consisted of a finger task in which subjects flexed and extended all fingers repeatedly in union, without the fingers touching each other. Both task consisted of 96 phases including 6 activations and rests contents. Post-processing was done on MRDx software program by using cross-correlation method. The result shows that there was an improvement in performance and also increased activation in several areas in the oxygen method. These finding demonstrates that while performing cognitive tasks, oxygen administration was due to increase of cerebral activation.

• Transactions on Electrical and Electronic Materials
• /
• 제18권1호
• /
• pp.21-24
• /
• 2017

Usually, the oxygen vacancy is an important factor in an oxide semiconductor device because the conductivity is related to the oxygen vacancy, which is formed at the interface between oxide semiconductors and electrodes with an annealing processes. ZTO is made by mixing n-type ZnO and p-type $SnO_2$. Zink tin oxide (ZTO), zink oxide (ZnO) and tin oxide ($SnO_2$) thin films deposited by RF magnetron sputtering and annealed, to generate the oxygen vacancy, were analyzed by XPS spectra. The contents of oxygen vacancy were the highest in ZTO annealed at $150^{\circ}C$, ZnO annealed at $200^{\circ}C$ and $SnO_2$ annealed at $100^{\circ}C$. The current was also increased with increasing the oxygen vacancy ions. The highest content of ZTO oxygen vacancies was obtained when annealed at 150. This is the middle level in compared with those of ZnO annealed at $200^{\circ}C$ and $SnO_2$ annealed at $100^{\circ}C$. The electrical properties of ZTO followed those of $SnO_2$, which acts a an enhancer in the oxide semiconductor.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.88-88
• /
• 2010

We synthesized molybdenum thin films deposited by RF magnetron sputtering and physicochemical analysis was performed. The physical and chemical properties of these films were examined with X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The obtained film at the oxygen ratio of 0% showed crystallinity of cubic Mo(110) phase. After the oxygen ratio increased more than 5% in the sputter gas, the molybdenum films were formed as an amorphous phase. The thickness of the Mo thin film was drastically decreased from 1000 nm to ca 70 nm after introduction of oxygen in the sputter gas confirmed by spectroscopic ellipsometer (SE) and scanning electron spectroscopy (SEM). The calculated band gap of the film deduced from SE data increased from 3.17 to 3.63 eV by addition of oxygen in the sputter gas. The roughness of the Mo film was examined with atomic force microscopy (AFM) and it was dramatically decreased by introducing of oxygen during sputtering. XPS results revealed that the ratio of metallic Mo species in the film decreased by the contents of Mo(VI) species increased at the ratio of oxygen increased in the sputter gas and fully oxidized at low content of oxygen in the sputter gas.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.17-19
• /
• 2002

Melt textured YBCO superconductors were fabricated by the top seeding method using Sml.8($Sm_{1.8}$ $Ba_{2.4}$ $Cu_{3.4}$$O_{7-Y}$) seed. We investigated the twin structures using the optical microscope, SEM and TEM. The twin structures formed during the tetragonal to orthorhombic transition which occurred at $450^{\circ}C$ in sample oxygen annealing. The twin structures were clearly observed by SEM due to the chemical etching effects. The lengths of twin structures were increased as the oxygenation heat treatment time increased from 1hr to 10hr. We investigated twin structure by TEM. The twin spaces were considered to be related to the oxygen contents. The results suggested an oxygen diffusion model for the formation of the twin lengths.

• 한국수소및신에너지학회논문집
• /
• 제19권4호
• /
• pp.348-358
• /
• 2008

Reduction reactivity and carbon deposition characteristics of mass produced oxygen carrier particle(OCN-650) have been investigated by using hydrogen, methane, syngas, and natural gas as fuels. For all fuels, the maximum conversion and oxygen transfer capacity increased as the temperature increase. The reduction rate and the oxygen transfer rate increased as the temperature increase for methane. However, those values showed maximum at 900$^{\circ}C$ for hydrogen, syngas, and natural gas. To explain consistently the change of maximum conversion, reduction rate, oxygen transfer capacity, oxygen transfer rate and degree of carbon deposition for different fuels, new parameters such as reactive carbon contents and require oxygen per input gas were adopted.

• 한국안광학회지
• /
• 제15권4호
• /
• pp.329-337
• /
• 2010

목적: RGP 콘택트렌즈들의 성분과 표면을 일관된 방법으로 분석하여, RGP 렌즈 재료의 성분 설계에 기본 정보를 제시하고자 하였다. 방법: 렌즈 재료의 구조는 적외선분광(FTIR), 표면 조성은 X-선 광전자분광(XPS), 표면의 형상과 거칠기는 원자현미경(AFM), 습윤성은 접촉각으로 평가하였으며, 상호관계와 경향을 분석하였다. 결과: 산소투과성이 높은 RGP 렌즈들은 불소를 줄이고, 실리콘의 양을 증가시키는 경향을 나타냈다. RGP 렌즈들의 재료는 실리콘과 불소의 증가에 따라 일정한 비율로 탄소와 산소가 감소하였으며, 탄소의 감소가 산소보다 3배 크게 나타났다. 그리고 표면처리가 된 재료는 탄소와 산소가 조성 변화 추세선에서 떨어져 있었다. 실리콘이 증가하면 미세입자의 응집이, 불소의 양이 증가하면 깊은 홈이 나는 형태로 표면이 거칠어졌으며, 거칠기에 대한 영향은 실리콘이 더 컸다. 실리콘과 불소가 증가하면 습윤성이 감소했는데, 실리콘에 의한 영향이 2배 크게 나타났다. RGP 렌즈 재료는 표면이 거칠어지면 습윤성이 감소하는 소수성의 형태를 나타냈다. 결론: RGP 렌즈들의 성분과 표면을 동일한 방법으로 측정하고, 상호관계를 분석하였다. 따라서 이 연구는 RGP 렌즈 재료의 성분 설계에 대한 기초 자료로 활용할 수 있을 것으로 사료된다.

• Environmental Engineering Research
• /
• 제21권4호
• /
• pp.427-435
• /
• 2016

In this study, change in water-dissolved oxygen (DO) was analyzed under various synthetic water qualities and nanobubbles (NBs) application conditions, such as gas type, initial DO as well as water dissolved, suspended and organic matters contents. When oxygen, rather than air, was introduced into nitrogen-desorbed ultra-pure water, the stagnation time was significantly increased. It took ten days for DO concentration to drop back to saturation. The higher the initial DO concentration, the longer particles were observed above saturation due to particle stability improvement. The oxygen mass transfer rate of 0.0482 mg/L/min was found to reach a maximum at an electrolytic concentration of 0.75 g/L, beyond which the transfer rate decreased due to adsorption of negative ions of the electrolyte at the interface. High levels of turbidity caused by suspended solids have become a barrier to dissolution of NBs oxygen into the water solution, and thus affected the transfer performance. On the other hand, by applying NBs for just an hour, up to 7.2% degradation of glucose as representative organic matter was achieved. Thus, NBs technology would maintain a high DO extent for an extended duration, and thus can improve water quality provided that water chemistry is closely monitored during its application.