• Industrial Engineering and Management Systems
• /
• v.4 no.2
• /
• pp.117-122
• /
• 2005

An assembly system (AS), a valuable tool for mass production, is generally composed of a number of workstations and a transport system. While the workstations perform some preplanned operations, the transport system moves the assemblies by special designed pallets from one station to another. One common problem associated with automatic assembly systems is that some assembly operations may have relatively long cycle times. As a consequence, the productivity, as determined by the operations with the longest cycle time, can be reduced significantly. Therefore, special forms of parallel workstations were developed to improve the performance of an assembly system. In this paper, three most commonly used parallel stations: on-line, off-line and tunnel-gated stations in a free transfer assembly system are studied via discrete event simulation. Our findings revealed that the off-line parallel system has the best performance because the two independent parallel stations can lower the buffer requirement; reduce the sensitivity to variability of processing time and balance of a line. On-line parallel systems were found to have a relatively poor performance, because the operations of two parallel stations block each other, and higher buffer capacity is required to achieve similar capacity. The tunnel-gated system was more efficient than the on-line system since the first parallel station can operate independently. More importantly, we have quantified the productivity of the three different strategies mentioned. Engineers can choose the optimal strategies for installing parallel stations under their working environment.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.3 no.3
• /
• pp.35-39
• /
• 1980

Although the product line produces a large volume of goods in a relatively short time, once the product line is established there are numerous problems that arise in connection with this product line. One of these problems is the problem of balancing operations or stations in terms of equal times and in terms of the times required to meet the desered rate of production. The objective of line balancing is minimizing the idle time on the line for all combinations of work stations subject to certain restrictions. In general, there are two types of line-balancing situations : (1) assembly line balancing and (2) fabrication line balancing. Two approaches to the assembly line balancing problem have been used. The first assumes a filed cycle time and find the optimum number of work stations. The second approach to the assembly line balancing problem assumes the number of work stations to be fixed and systematically coverages on a solution which minimizes the total delay time by minimizing the cycle time. Here the cycle time is determined by the longest station time. In this paper, by using the second approach method, a general mathematical model, problem solutions, and computer program for the assembly line balancing problem is presented. Data used is obtained from the company which has been confronted with many problems arising in connection with their assembly line.

• Industrial Engineering and Management Systems
• /
• v.10 no.3
• /
• pp.197-202
• /
• 2011

In traditional production lines, such as assembly lines, each worker is usually assigned to a particular fixed work, and decreasing the task to master the assigned work is valuated. However, when an imbalance exists between workers' speeds, if a worker delays the overall work in the production line, the production rate of the particular line will also decrease. To avoid this problem, the "Self-Balancing Production Line" was introduced. In this type of production line, each worker is assigned work dynamically, and when specific conditions are satisfied, production remains balanced. Characteristics of these lines that can be preempted at any place have already been analyzed by some researchers. A previous paper examined the situation in which only a single worker can process one machine and cannot preempt processing, and the improved policy of an ordinary selfbalancing production line, which specifies which stations workers can process and how workers can behave. This policy achieveda high production rate with only four stations and two workers (Buzacott, 2002). In that paper, worker processing stations and the behavior of a specific worker were limited, andthe paper focused only on specific stations and workers. Therefore, it is not applicable to any worker sequence. In this paper, we focus on other ways to decrease cycle time. In this kind of line, a worker processes at his or her speed. Therefore, if a worker is assigned stations according to his or her speed, the line can decrease cycle time. To do so, we relax the assumptions of this type of line and set a new condition. Under these conditions, we compare our results to the results of previous papers.

• Journal of the Regional Association of Architectural Institute of Korea
• /
• v.20 no.6
• /
• pp.63-70
• /
• 2018

This study is aimed to reflect the current status survey, analysis and response of 10 railway stations using geographical names in one of 19 stations located on Gyeongbu, Honam and Chungbuk line. Most railway stations in the study have shown normal images that are close to the standard type by selecting similar building materials rather than reflecting geographical features. Aside from the shape of the traditional Korean house in Cheongju, almost all newly constructed stations tend to incorporate light gray plating material on their modern exterior to produce Family look design as a railroad station. According to a survey of the sensitivity of the station's name, Osong Station was 73.6 percent, Gyeryong Station 67.3 percent, Heukseok-ri Station was 64.5 percent, Shintan-jin 62.6 percent, and Yeonsan Station 57 percent, more than half. Therefore, the results of the five stations were presented as a calculation and proposed design release focusing on the facades of each station. Each of these stations suggested a way to express the facade design image, considering the railway operation status of Korea Railroad, the area of the station and other surroundings.

• Journal of Environmental Health Sciences
• /
• v.30 no.5 s.81
• /
• pp.469-480
• /
• 2004

The radon concentrations were measured to survey distribution of radon concentrations in Seoul subway stations. The radon concentrations in air and water were measured at seventeen subway stations(Mapo, Chungjongno, Sodaemun, Kwanghwamun, Chongno3ga, Ulchiro4ga, Tangdaemun, Sangildong on Line 5;Nowon, Chunggye, Hagye, Kongnung, Taenung, Mokkol, Chunghwa, Sangbong, Myomok on Line 7) using the $RAdtrak^{TM}$ radon gas detector, Pylon AB-5 continuous passive radon detector and liquid scintillation counting method from January to May 1999. The major results obtained from this study were as follows: The long-term mean concentrations of radon were $61.8\;Bq/m^3$ in office, $78.9\;Bq/m^3$ in platform, $38.2\;Bq/m^3$ in concourse and $20.1\;Bq/m^3$ in outdoor, respectively. These levels were less than the action level ($148\;Bq/m^3$) of the U.S. EPA. The highest level of short-term mean concentrations was $116.55\;Bq/m^3$ at Chongno3ga station on the 5th line subway stations, while the lowest mean concentration was $19.55\;Bq/m^3$ at Mokkol station on the 7th line subway stations. The highest concentration of radon in the road water and storing underground water in the subway stations was $234.7\;KBq/m^3\;and\;155.5\;KBq/m^3$ in Sodaemun subway station, respectively. The results suggest that radon concentration in subway stations seems to be affected by ventilation and radon concentratin in underground water in the subway stations.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.18 no.2
• /
• pp.1-22
• /
• 1993

This paper deals with the problem of mixed model assembly line balancing. In mixed model assembly lines, tsks should be assigned to stations in such a manner that all stations have approximately the same amount of work on a production cycle basis. Further in balancing assembly lines, the related tasks, the performing task side and the team tasks should be considered to improve work methods, to give more job satisfaction to workers, and to allow greater flexibility in the design of assembly lines. In this paper, the heuristic dispatch assignment rule is developed to assign evenly tasks of each model to all stations. The heuristic method based on the assignment rule developed is presented for mixed model assembly line balancing with the considerations of the related tasks, the performing task side, and the team tasks. The proposed method is analyzed, and compared with other methods for line balancing.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.3
• /
• pp.27-39
• /
• 2009

The 1st Incheon Rapid Transit Line opened in October, 1999. However, the current development plans for areas near stations do not involve plans for the both urban planning and transportation together. As the focus on only the aspect of installing a new transportation mode, the developments even make the problems such as reckless development and traffic congestion gets worse. It is required to analyse status of the current land uses and land use plans in the future and consider distribution of functions of the areas near stations and aims of development plans so as to harmonize the functions of each region in view of making balance in the whole city. The aims of developments of areas near stations has to focus on the study follows steps to find and suggest aims and strategies for the revitalization plan for areas near stations with considering the both transportation and land uses together. The plans for the areas near stations of the Incheon 1st Rapid Transit Line are analysed and then the features and rational strategies are derived. The impact is analysed as applying the development strategies derived from the step into the areas near the stations of Incheon 1st Rapid Transit line.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.19 no.2
• /
• pp.217-228
• /
• 1994

This paper presents a new integer formulation (Type III ALB) for a single model assembly line balancing problem. The objective of the formulation is to minimize the total idle time, which is defined as the product of the number of work stations and the cycle times minus the total work content. This formulation considers currently existing Type I (minimizing the number of work stations for a given cycle time) and type II (minimizing the cycle time for a given number of work stations) formulations as its special cases and provides the global minimum solutions of the cycle time and the number of work stations. This information would be of great value to line designers involved in designing new assembly lines and rebalancing old lines under flexible conditions. Solution methods based on combination of Type I and Type II approaches are also suggested and compared.

• Korean Management Science Review
• /
• v.13 no.2
• /
• pp.25-48
• /
• 1996

Mixed Model Assembly Lines (MMALs) are increasingly used to produce differentiated products on a single assembly line without work-in-process storage, Usually, a typical MMAL consists of a number of (1) stations doing exactly the same operation on every job, (2) stations involving operations with different choices, and (3) stations offering operations that are not performed on every job, or that are performed on every job but with many options. For stations of the first type there is no sequencing problem at all. However, for the second type a set-up cost is incurred each time the operation switches from one choice to another. At the third type of stations, different models, requring different amounts and choices of assembly work, creates an uneven flow of work along the line and variations in the work load at these stations. When a subsequence of jobs requires more work load than the station can handle, it is necessary to help the operations at the station or to complete the work elsewhere. Therefore, a schedule which minimize the sum of set-up cost and utility work cost is desired. So this study has developed Fixed Random Ordering Rule (FROR), Fixed Ascending Ordering Rule (FAOR), Fixed Descending Ordering Rule, and Extended NHR (ENHR). ENHR is to choose optimal color ordering of each batch with NHR, and to decide job sequence of the batch with it, too. As the result of experiments, ENHR was the best heuristic algorithm. NHR is a new heuristic rule in which only the minimum addition of violations from both partial sequence and unassigned sequence at every branch could be considered. And this is a heuristic sequencing rule for the third type of stations at MMAL. This study developed one more heuristic algorithm to test the performance of NHR, which is named as Practical Heuristic Rule (PHR).

• Proceedings of the KIEE Conference
• /
• 1997.07c
• /
• pp.903-906
• /
• 1997

When large capacity generation stations that consist of several large units tend to pull out of step from main power system, stabilizing control scheme as emergency control for preventing loss of synchronism of the whole stations with the remaining system is devided into two steps that the first step is to perform on-line prediction for out-of-step and the next step is on-line calculation of the amount of generation shedding for the rest of generators to be in step when out of step is expected. This paper presents on-line prediction scheme for out-of-step based on P-$\delta$ curve estimation using real-time measurement and on-line calculation of generation shedding. The proposed stabilizing scheme was applied to case study of real power system and the results obtained by the method compare well with the results by simulation.