• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.1
• /
• pp.65-73
• /
• 2007

This paper presents an on-line correction method of current measurement errors for a pure-integration-based flux estimation down to 1-Hz stator frequency. An observer-based approach is taken as one possible solution of eliminating the dc offset and the negative sequence component of unbalanced gains in the synchronous coordinate. At the same time, the positive sequence component estimation is performed by creating an error signal between a motor model reference and an estimated q-axis rotor flux established by a permanent magnet (PM) in the synchronous coordinate. The compensator utilizes a PI controller that controls the error signal to zero. The proposed technique further contains a residual error compensator to completely eliminate miscellaneous disturbances in the estimated flux. The developed algorithm has been implemented on a 1.1-kW permanent magnet synchronous motor (PMSM) drive to confirm the effectiveness of the proposed scheme.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.5
• /
• pp.109-114
• /
• 2009

An orthogonal frequency division multiplexing(OFDM) system is effective to bandwidth because of orthogonality of subcarriers and robust to multipath fading. However, if there is a frequency offset, we lose the orthogonality of subcarriers and that results in inter-carrier interference(ICI) which increases errors in the system. In this paper, we propose an algorithm that estimates the fine frequency offset using a correlation method in OFDM systems. This scheme compares two correlation values in different frequency offsets with opposite directions. From the difference between two correlation values we can derive a fine frequency offset estimation algorithm. Its performance is verified by computer simulations.

• Journal of computational fluids engineering
• /
• v.19 no.1
• /
• pp.34-40
• /
• 2014

Conjugate heat transfer of an automotive oil cooler with offset-strip fins was numerically investigated to predict the performance of the oil cooler for various flow-rates. The simulations were conducted by directly modeling offset-strip fins with unstructured meshes. The incompressible Navier-Stokes equations coupled with energy equation were used for the present simulations. Heat transfer characteristics of the oil cooler was compared well with experimental results and the errors were approximately within 5 percents. It was found that the performance of the oil cooler increased as the flow-rate increased up to the flow-rate of 12 L/min, but the performance seemed to be saturated beyond a critical flow-rate, which was estimated as 15 L/min. Furthermore, it was confirmed that compared to the performance without fins, that of the oil cooler with offset-strip fins was increased by about 75 percents.

• The Journal of the Korea Contents Association
• /
• v.9 no.7
• /
• pp.76-85
• /
• 2009

UWB signal with high resolution capability can be used to estimate ranging and positioning in wireless personal area network. The node works on its local clock and the frequency differences of nodes have serious affects on ranging algorithms estimating locations of mobile nodes. The low rate UWB, IEEE802.15.4a, describes asynchronous two way ranging methods such as TWR and SDS-TWR working without any additional network synchronization, but the algorithms can not eliminate the effect of clock frequency differences. Therefore, the mechanisms to characterize the crystal difference is essential in typical UWB PHY implementations. In high rate UWB, characterizing of crystal offset with tracking loop is not required. But, detection of the clock frequency offset between the local clock and remote clock can be performed if there is little noise induced jitter. In this paper, we complete related ranging equations of high rate UWB based on TWR with relative frequency offset, and analyze a residual error in the ideal equations. We also evaluate the performance of the relative frequency offset algorithm by simulation and analyze the ranging errors according to the number of TWR to compensate coarse clock resolution. The results show that the relative frequency offset compensation and many times of TWR enhance the performance to converge to a limited ranging errors even with coarse clock resolutions.

• Journal of Communications and Networks
• /
• v.8 no.1
• /
• pp.38-48
• /
• 2006

A synchronous multicarrier (MC) code-division multiple access (CDMA) system using inverse fast Fourier transform (IFFT) and fast Fourier transform (FFT) for the downlink mobile communication system operating in a frequency selective Rayleigh fading channel is analyzed. Both carrier frequency offset and timing offset are considered in the analysis. Bit error rate performance of the system with both equal gain combining and maximum ratio combining are obtained. The performance is compared to that of the conventional system using correlation receiver. It is shown that when subcarrier number is large, the system using IFFT/FFT has nearly the same performance as the conventional one, while when the sub carrier number is small, the system using IFFT/FFT will suffer slightly worse performance in the presence of carrier frequency offset.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.277-280
• /
• 2008

Enhancing the positioning precision is the primary pursuit of GPS users. To achieve this goal, most studies have focused on the relationship between GPS receiver clock errors and GPS positioning precision. This study utilizes undifferentiated phase data to calculate GPS clock errors and to compare with the frequency of cesium clock directly, thus verifying estimated clock errors by the method used in this paper. The relative frequency offsets from this paper and from National Standard Time and Frequency Laboratory of Taiwan match to $1.5{\times}10^{12}$ in the frequency instability, suggesting that the proposed technique has reached a certain level of quality. The built-in quartz clocks in the GPS receivers yield relative frequency offsets that are 3 to 4 orders higher than those of rubidium clocks. The frequency instability of the quartz clocks is on average two orders worse than that of the rubidium clock. Using the rubidium clock instead of the quartz clock, the horizontal and vertical positioning accuracies were improved by 26-78% (0.6-3.6 mm) and 20-34% (1.3-3.0 mm), respectively, for a short baseline. These improvements are 7-25% (0.3-1.7 mm) and 11% (1.7 mm) for a long baseline. Our experiments show that the frequency instability of clock, rather than relative frequency offset, is the governing factor of positioning accuracy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1438-1441
• /
• 2005

To establish of standard technique of nano-length measurement in 2D plane, new AFM system has been designed. In this system, measurement uncertainty is dominantly affected by the Abbe error of XY scanning stage. No linear stage is perfectly straight; in other words, every scanning stage is subject to tilting, pitch and yaw motion. In this paper, an AFM system with minimum offset of XY sensing is designed. And XY scanning stage is designed to minimize rotation angle because Abbe errors occur through the multiply of offset and rotation angle. To minimize the rotation angle optimal design has performed by maximizing the stiffness ratio of motion direction to the parasitic motion direction of each stage. This paper describes the design scheme of full AFM system, especially about XY stage. Full range of fabricated XY scanner is $100um\times{100um}$. And tilting, pitch and yaw motion are measured by autocollimator to evaluate the performance of XY stage. Using this AFM system, 3um pitch specimen was measured. As a result, the uncertainty of total system has been evaluated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.7
• /
• pp.1038-1046
• /
• 2004

In order to acquire high-speed and high-precision performances in servomechanisms, an integrated design method have been proposed. Based on strict mathematical modeling and analysis of system performance according to design and operating parameters, a nonlinear constrained optimization problem including the relevant subsystem parameters of the servomechanism is formulated. Optimum design results of mechanical and electrical parameters are obtained according to the design parameters specified by designers through the integrated design processes. Motors are optimally selected from the servo motor database. Both the geometric errors referring to Abbe offset and the contour errors are minimized while required constraints such as stability conditions and saturated conditions are satisfied. This design methodology both offers the improved possibility to evaluate and optimize the dynamic motion performance of the servomechanism and improves the quality of the design process to achieve the required performance for high-speed/precision servomechanisms.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.5
• /
• pp.473-481
• /
• 2013

A fractional folding analog-to-digital converter (ADC) with a novel arithmetic digital encoding technique is discussed. In order to reduce the asymmetry errors of the boundary conditions for the conventional folding ADC, a structure using an odd number of folding blocks and fractional folding rate is proposed. To implement the fractional technique, a new arithmetic digital encoding technique composed of a memory and an adder is described. Further, the coding errors generated by device mismatching and other external factors are minimized, since an iterating offset self-calibration technique is adopted with a digital error correction logic. A prototype 8-bit 1GS/s ADC has been fabricated using an 1.2V 0.13 um 1-poly 6-metal CMOS process. The effective chip area is $2.1mm^2$(ADC core : $1.4mm^2$, calibration engine : $0.7mm^2$), and the power consumption is 88 mW. The measured SNDR is 46.22 dB at the conversion rate of 1 GS/s. Both values of INL and DNL are within 1 LSB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1190-1196
• /
• 2014

This paper presents the design of a Frequency Modulated Continuous Wave(FMCW) radar altimeter with wide altitude range and low measurement errors. Wide altitude range is achieved by employing the optic delay in the transmitting path to reduce the dynamic range of measuring altitude. Transmitting power and receiver gain are also controlled to have the dynamic range of the received power be reduced. In addition, low measurement errors are obtained by improving the sweep linearity using the Direct Digital Synthesizer(DDS) and minimizing the phase noise employing the reference clock(Ref_CLK) as the offset frequency of the Phase Locked Loop(PLL).