• Journal of the Korean institute of surface engineering
• /
• v.45 no.3
• /
• pp.106-110
• /
• 2012

Oblique angle deposition (OAD) is a physical vapor deposition where incident vapor flux arrives at non-normal angles. It has been known that tilting the substrate changes the properties of the film, which is thought to be a result of morphological change of the film. In this study, OAD has been applied to prepare single and multilayer TiN films by cathodic arc deposition. TiN films have been deposited on cold-rolled steel sheets and stainless steel sheet. The deposition angle as well as substrate temperature and substrate bias was changed to investigate their effects on the properties of TiN films. TiN films were analyzed by color difference meter, scanning electron microscopy, nanoindenter and x-ray diffraction. The color of TiN films was not much changed according to the deposition conditions. The slanted and zigzag structures were observed from the single and multilayer films. The relation between substrate tilting angle (${\alpha}$) and the growth column angle (${\beta}$) followed the equation of $tan{\alpha}=2tan{\beta}$. The indentation hardness of TiN films deposited by OAD was low compared with the ones prepared at normal angle. However, it has been found that $H^3/E^2$ ratio of 3-layer TiN films prepared at OAD condition was a little higher than the ones prepared at normal angle, which can confirm the robustness of prepared films.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.2
• /
• pp.79-86
• /
• 2002

In end milling process the undeformed chip thickness and the cutting force components vary periodically with phase change of the tool. In this study, up end milling process is transformed to the equivalent oblique cutting. The varying undeformed chip thickness and the cutting force components in end milling process are replaced with the equivalent average ones. Then it can be possible to analyze the chip-tool friction and shear process in the shear plane of the end milling process by the equivalent oblique cutting system. According to this analysis, when cutting Inconel 718, 61, 64 and 55% of the total energy is consumed in the shear process with the helix angle 30$^{\circ}$, 40$^{\circ}$ and 50$^{\circ}$ respectively, and the balance is consumed in the friction process. With the helix angle of 40$^{\circ}$ the specific cutting energy consumed is smaller than with the helix angle 30$^{\circ}$ and 50$^{\circ}$.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.2
• /
• pp.1-5
• /
• 2002

Alignment effects for nematic liquid crystal (NLC) and electro-optical (EO) characteristics of the ion beam (IB) aligned twisted nematic (TN)-liquid crystal display (LCD) with oblique ion beam exposure on the diamond-like carbon (DLC) thin film surface were studied. A high pretilt angle of 3.5$^{\circ}$ in NLC by ion beam exposure on the DLC thin film layer can be measured. An excellent voltage-transmittance (V-T) curve of the ion beam aligned TN-LCD was observed with oblique ion beam exposure on the DLC thin film surface for 1 min. Also, a faster response time for the ion beam aligned TN-LCD with oblique ion beam exposure on the DLC thin film surface for 1 min can be achieved.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.4 s.23
• /
• pp.5-13
• /
• 2005

The impact of a long-rod penetrator into oblique plates with combined obliquity and yaw is investigated. The study was done using a newly developed three dimensional dynamic and impact analysis code, which uses the explicit finite element method. Through the comparison of simulation result with experimental result and other code's result, the adaptability and accuracy of the developed code is evaluated under the complex situation in which yaw angle and oblique angle exist simultaneously. As a result of comparison, it has found that deformed shape, residual length and velocity, rotational velocity of long-rod show good agreement with experimental data. Through this study, the applicability and accuracy of the code as a metallic armour system design tool is verified.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.1 s.24
• /
• pp.127-134
• /
• 2006

The protection capability against an enhanced long rod(L/D=30) with yaw is investigated numerically and compared with that of shorter one(L/D=15). In addition details of interactions between yawed long rods and oblique plate velocity are examined. Through the simulation results, we find that dual flying plates system is more effective with longer rod due to the elongated disturbance. The protection performance is more effective for the penetrator with $+6^{\circ}$ of yaw angle than that with a yaw angle of $-6^{\circ}$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.4
• /
• pp.429-435
• /
• 1998

Experiments were conducted to investigate the turbulent flow characteristics from on oblique impingement surface to an plane jet at the jet Reynolds number(Re based on the nozzle width) $3{\times}10^4$ The jet mean velocity and turbulent intensity profiles have been measured along the impingement surface by hot-wire anemometer. The nozzle-to-plate distance(H/B) ranged from 2 to 10 and the oblique angle (a) from 45 to 90 degree. Also the secondary peak of the turbulent intensity was observed at H/B=4 S/B 5 and a=90 degree. It has been found that the stagnation point shifted toward the minor flow region as the oblique angle decreased and the position of the stagnation point nearly coincided with that of the maximum turbulent intensity.

• Journal of the Korean Society for Precision Engineering
• /
• v.1 no.2
• /
• pp.24-32
• /
• 1984

The object of the study is to discuss the effect of magic ink as a surface active substance on the mechanism of chip formation in oblique cutting. The Rehbinder effect has been known as a phenomenon that the mechanical strength reduces when the metal is coated with some surface active substances. In order to interpret these surface effects defined by Rehbinder, the influence on the shear strength of shear plane by coating surface active substances, cutting force by the depth of cut, surface roughness and hardness ratio were observed. The results are as follows: 1. By coating the magic ink on free surface of the forming chip, the effective shear angle increases, and the cuttinbg force and the deformed chip thickness decreases. 2. With the large inclination angle the effective shear angle increases, and the specific cutting force and the friction angle decrease. 3. Cutting of the coated surface improves the surface roughness and the hardness ratio drops, which means another Rehbinder effect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.259-262
• /
• 1998

The liquid crystal (LC) alignment and pretilt angle generation using photo-alignment method were investigated in this study. We obtained that the monodomain alignment of nematic(N) LC increases with increasing irradiation time in a cell with linearly polarized ultraviolet (LPUV) light irradiation on polyimide (Pl) surfaces. We consider that the monodomain alignment is able to be anisotropic dispersion force due to photo-depolymerization of polymer with LPUV light irradiation on Pl surface. Also, we observed that the uniform alignment of NLC is obtained in a cell with normally LPUV light irradiated on Pl surface at 30 min. and then oblique LPUV is secondly irradiated on Pl surfaces rotated by 90$^{\circ}$. The pretilt angle of NLC is generated about 1.5$^{\circ}$ with oblique angle 60$^{\circ}$.

• Journal of applied mathematics & informatics
• /
• v.26 no.5_6
• /
• pp.1207-1214
• /
• 2008

We give an elementary proof of one of the main results in [H.O. Kim, R.Y. Kim, J.K. Lim, The infimum cosine angle between two finitely generated shift-invariant spaces and its applications, Appl. Comput. Har-mon. Anal. 19 (2005) 253-281] concerning the existence of an oblique projection onto a finitely generated shift-invariant space along the orthogonal complement of another finitely generated shift-invariant space under the assumption that the generators generate Riesz bases.

• Korean Institute of Interior Design Journal
• /
• v.24 no.1
• /
• pp.64-71
• /
• 2015

This study aims to disclose the dynamics of Daniel Libeskind Museums by the principles of counterbalance. Balance as a dynamic concept is the settlement of instability and tension and to draw overall sense of balance by controlling new perception elements that may cope with the unbalance elements. This is based on balancing compensation and can be explained as a counterbalance. Daniel Libeskind, a representative architect of deconstructivism, creates dynamic space by using oblique lines on the plane. The study was carried out under the assumption that this space would be designed under the certain principles rather than the result of momentary feelings and the analysis was conducted by the counterpoint of music and counterbalance. As a result, Daniel Libeskind balances in a way of forming the mutual right angle by using oblique lines which cancel out the unbalance in plane composition or making the same angle based on vertical / horizontal axis. Counterbalance has been achieved in the section and elevation as well as plane and complex and diverse oblique lines were worked under the constant principle not accidental results. The axes of Daniel Libeskind's architecture have been known to follow contextualism with symbolism and historicity but it was found that a design technique considering counterbalance was used in the overall control.