• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.2C
• /
• pp.173-177
• /
• 2008

In this paper, we improve performance of Low Density Parity Check (LDPC) codes with adding a large number of short cycles. Short cycles, especially cycles of length 4, degrade performance of LDPC codes if the standard BP (Belief Propagation) decoding is used. Therefore current researches have focused on removing cycles of length 4 for designing good performance LDPC codes. We found that a large number of cycles of length 4 improve performance of LDPC codes if a modified BP decoding is used. We present the modified BP decoding algorithm for LDPC codes with a large number of short cycles. We show that the modified BP decoding performance of LDPC codes with a large number of short cycles is better than the standard BP decoding performance of LDPC codes designed by avoiding short cycles.

• International journal of steel structures
• /
• v.18 no.4
• /
• pp.1242-1251
• /
• 2018

Not all loads contribute to fatigue crack propagation in the welded detail of steel bridges when they are subjected to variable amplitude loading. For fatigue assessment, therefore, non-contributing stress cycles should be truncated. However, stress range truncation is not considered during typical fatigue reliability assessment. When applying the first order reliability method, stress range truncation occurs mismatch between the expected number of cycles to failure and the number of cycles obtained at the time of evaluation, because the expected number of cycles only counts the stress cycles that contribute to fatigue crack growth. Herein, we introduce a calibration factor to coordinate the expected number of cycles to failure to the equivalent value which includes both contributing and non-contributing stress cycles. The effectiveness of stress range truncation and the proposed calibration factor was validated via case studies.

• Structural Engineering and Mechanics
• /
• v.11 no.3
• /
• pp.301-314
• /
• 2001

The purpose of this experimental study is to investigate the damage mechanism due to shear-fatigue behavior of high-strength reinforced concrete beams under repeated loading. The relationship between the number of cycles and the deflection or strain, the crack growths and modes of failure with the increase of number of cycles, fatigue strength, and S-N curve were observed through a fatigue test. Based on the fatigue test results, high-strength reinforced concrete beams failed at 57-66 percent of static ultimate strength for 2 million cycles. The fatigue strength at 2 million cycles from S-N curves was shown as about 60 percent of static ultimate strength. Compared to normal-strength reinforced concrete beams, fatigue capacity of high-strength reinforced concrete beams was similar to or lower than fatigue capacity of normal-strength reinforced concrete beams. Fatigue capacity of normal-strength reinforced concrete beams improved by over 60 percent.

• Transactions of Materials Processing
• /
• v.27 no.6
• /
• pp.347-355
• /
• 2018

This study investigated the effects of the processing number of multi-axial diagonal forging (MADF) on the microstructural changes of OFC fabricated by MADF processes. The as-extruded OFC was cut to $25mm^3$ cube for the MADF processes. The MADF process consists of plane forging with a thickness reduction of 30% and diagonal forging with a diagonal forging angle of $135^{\circ}$. In order to analyze the microstructural evolutions according to the number of repetitions, 1, 2, 3 and 4 cycles of the MADF process were performed. OFC specimens were successfully deformed without surface cracking for up to 4 cycles of MADF. The grain size, average misorientation and average grain orientation spread (GOS) of MADF processed materials were analyzed using EBSD technique and their Vicker's hardness were also measured. The results showed that MADF process effectively refined the microstructure of OFC with initial average grain size of $84.2{\mu}m$. The average grain sizes of specimens MADF processed for 1, 2, 3, 4 cycles were refined to be $8.5{\mu}m$, $2.2{\mu}m$, $1.5{\mu}m$, $1.1{\mu}m$, respectively. The grain refinement seemed to be saturated when OFC was MADF processed over 2 cycles. In the case of specimens subjected to two or more cycles of MADF, the degree of decrease in average grain size was drastically reduced as the number of cycles increased due to softening phenomena such as dynamic recovery or dynamic recrystallization during processing. The degree of increase in average Vicker's hardness was also dramatically reduced as the number of cycles increased due to the same reason.

• Clinical and Experimental Reproductive Medicine
• /
• v.47 no.3
• /
• pp.227-232
• /
• 2020

Objective: The aim of this study was to compare in vitro fertilization outcomes between fresh day 3 or day 4 embryo transfer cycles with dual progesterone (P) administration (intramuscular and vaginal) and cycles with single intramuscular P administration for luteal support. Methods: We selected 124 cycles from 100 women (under age 40 years) who underwent oocyte pick-up (number of trials ≤ 3, 4-14 oocytes obtained) and transfer of two or three day 3 or day 4 embryos at two infertility centers from January 2014 to June 2019. Dual P (intramuscular P [50 mg] daily+vaginal P) was used in 52 cycles and a single intramuscular administration of P (50 mg daily) was used in 72 cycles. Results: Women's age, infertility factors, number of oocytes retrieved, number of transferred embryos, and mean embryo score were similar between the dual P group and the single P group. Although the number of trial cycles was significantly higher (1.9 vs. 1.5), and the mean endometrial thickness on the trigger day (10.0 mm vs. 11.0 mm) was significantly lower in the dual P group, the implantation rate, clinical pregnancy rate, ongoing pregnancy rate, and miscarriage rate for both day 3 and day 4 transfers were similar between the two groups. Conclusion: In fresh day 3 or day 4 embryo transfer cycles, dual P administration did not demonstrate any clinical advantages. Intramuscular P alone appears to be sufficient for luteal support.

• Clinical and Experimental Reproductive Medicine
• /
• v.43 no.1
• /
• pp.38-43
• /
• 2016

Objective: The number of assisted reproductive technology (ART) clinics, ART cycles, clinical pregnancy rate (CPR), and number of newborns conceived using ART have steadily increased in South Korea. This aim of this study was to describe the status of ART in South Korea between January 1 and December 31, 2011. Methods: A localized online survey was created and sent to all available ART centers via email in 2015. Fresh embryo transfer (FET) cases were categorized depending on whether standard in vitro fertilization, intracytoplasmic sperm injection (ICSI), or half-ICSI procedures were used. Thawed embryo transfer (TET) and other related procedures were surveyed. Results: Data from 36,990 ART procedures were provided by 74 clinics. Of the 30,410 cycles in which oocytes were retrieved, a complete transfer was performed in 91.0% (n=27,683). In addition, 9,197 cycles were confirmed to be clinical pregnancies in the FET cycles, representing a pregnancy rate of 30.2% per oocyte pick-up and 33.2% per ET. The most common number of embryos transferred in the FET procedures was three (38.1%), followed by two (34.7%) and one (14.3%). Of the 8,826 TET cycles, 3,137 clinical pregnancies (31.1%) were confirmed by ultrasonography. Conclusion: While the overall clinical pregnancy rate for the TET cycles performed was lower than the rate reported in 2010 (31.1% vs. 35.4%), the overall CPR for the FET cycles was higher than in 2010 (33.2% in 2011 and 32.9% in 2010). The most common number of embryos transferred in FET cycles was three, as was the case in 2010.

• Bulletin of the Korean Mathematical Society
• /
• v.44 no.3
• /
• pp.385-394
• /
• 2007

An upper bound of the basis number of the semi-strong product of cycles with bipartite graphs is given. Also, an example is presented where the bound is achieved.

• Structural Engineering and Mechanics
• /
• v.28 no.5
• /
• pp.495-514
• /
• 2008

In this paper, experimental and theoretical investigations of the effect of the mean moment on the response and collapse of circular thin-walled tubes subjected to cyclic bending are discussed. To highlight the influence of the mean moment effect, three different moment ratios r (minimum moment/ maximum moment) of -1, -0.5 and 0, respectively, were experimentally investigated. It has been found that the moment-curvature loop gradually shrinks with the number of cycles, and becomes stable after a few cycles for symmetric cyclic bending (r = -1). However, the moment-curvature loop exhibits ratcheting and increases with the number of cycles for unsymmetric cyclic bending (r = -0.5 or 0). In addition, although the three groups of tested specimens had three different moment ratios, when plotted in a log-log scale, three parallel straight lines describe the relationship between the controlled moment range and the number of cycles necessary to produce buckling. Finally, the endochronic theory combined with the principle of virtual work was used to simulate the relationship among the moment, curvature and ovalization of thin-walled tubes under cyclic bending. An empirical formulation was proposed for simulating the relationship between the moment range and the number of cycles necessary to produce buckling for thin-walled tubes subjected to cyclic bending with different moment ratios. The results of the experimental investigation and the simulation are in good agreement with each other.

• Kyungpook Mathematical Journal
• /
• v.48 no.2
• /
• pp.303-315
• /
• 2008

In [8] M. Y. Alzoubi and M. M. Jaradat studied the basis number of the composition of paths and cycles with Ladders, Circular ladders and M$\"{o}$bius ladders. Namely, they proved that the basis number of these graphs is 4 except possibly for some cases in each of them. Since the lexicographic product is noncommutative, in this paper we investigate the basis number of the lexicographic product of the different kinds of ladders with paths and cycles. In fact, we prove that the basis number of almost all of these graphs is 4.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.257-263
• /
• 2001

Terminal paging is the process of determining the exact location of a particular mobile terminal. The paging cost is related to the number of paging cycles and the number of cells being polled by each cycle. In this paper, we first analyze the performance of various terminal paging strategies in terms of the number of polling cycles and the number of polling signals. Then we present a paging scheme which combines Shortest-Distance-First with movement history list. Simulation results show that the proposed paging scheme reduces the number of polling signals as well as the number of polling cycles.