• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.2
• /
• pp.264-269
• /
• 2009

Marginal Loss Factor(MLF) is represented as the sensitivity of transmission loss, which is computed from the change of the generation at slack bus by the change of the load at the arbitrary bus. The MLF dependent on the selection of slack bus is one of the key factors affecting nodal pricing, Genco's profits, social welfare(SW) and Nash Equilibrium in a competitive electricity market. This paper addresses the methodology of slack bus selection by using Cournot model of Cost Based Pool market. Numerical results from sample cases show that the slack bus of MLF of the highest average is beneficial from the view points of SW.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.729-731
• /
• 2000

This paper presents a simple method for determining the minimum value of capacitance required for initiating self excitation in three-phase self-excited induction generator. Based on the steady-state equivalent circuit model, this paper presents simple and direct method to find the minimum capacitance requirement under R-L load. Using the loop impedance and nodal admittance. the minimum capacitance is determined by self excitation condition. These computed values can be used to predict practically the minimum value of the terminal voltage required for self-excitation. To maintain a constant terminal voltage, a method for determining the frequency, terminal capacitance, and exciting reactance is also described.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1996.04a
• /
• pp.1-8
• /
• 1996

Many studies showed that small imperfections can also have a considerable influence on the behaviour of structures. Especially, in Single-Layer Latticed Domes, initial imperfection occurred by human error and construction error is very important to the buckling load. The definition of imperfection is that a node of structure shifts from perfect condition. For example, in the case of truss structures, imperfections are represented by shifting the location of nodal points relative to the position in which they would be for a perfect structure. This paper uses Arc-length Method in nonlinear iteration analysis, choosing star dome, in which many studies have been accomplished, as a model. The results of analysis show that initial imperfection can reduce the buckling load of structures.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.10a
• /
• pp.190-197
• /
• 2000

A moment-curvature relationship to simulate the behavior of reinforced concrete beam under cyclic loading is introduced. Unlike previous moment-curvature models and the layered section approach, the proposed model takes into consideration the bond-slip effect by using monotonic moment-curvature relationship constructed on the basis of the bond-slip relation and corresponding equilibrium equation at each nodal point. In addition, the use of curved unloading and reloading branches inferred from the stress-strain relation of steel gives more exact numerical result. The advantages of the proposed model, comparing to layered section approach, may be on the reduction in calculation time and memory space in case of its application to large structures. The modification of the moment-curvature relation to reflect the fixed-end rotation and pinching effect is also introduced. Finally, correlation studies between analytical results and experimental studies are conducted to establish the validity of the proposed model.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.10a
• /
• pp.331-338
• /
• 2000

In this paper, a non-linear finite element formulation for the spatial cable-net structures is simulated and using this formulation, the characteristics of structural behaviors for the elastic catenary cable are examined In the simulating procedure for the elastic catenary cable, nodal forces and tangential stiffness matrices are derived using catenary parameters of the exact solutions by a governing differential equation of catenary cable, cable self-weights and unstressed cable length. Dynamic Relaxation Method that considers kinetic damping is used for the structure analysis and Newton Raphson Method is used to verify the accuracy of solutions. In the analysis of two dimensional cable, the results obtain from the elastic catenary elements are shown more accurate than does of truss elements and in the case of spatial cable-net structures, Dynamic Relaxation Method is more stable to be converged than Newton Raphson Method.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.251-258
• /
• 2003

The early -age behavior of base restrained reinforced concrete (RC) walls is analyzed using a three-dimensional finite element method in this study. After calculating the temperature and internal relative humidity variations of an RC wall, determination of stresses due to thermal gradients, differential drying shrinkage, and average drying shrinkage is followed, and the relative contribution of these three stress components to the total stress is compared. The mechanical properties of early-age concrete, determined from many experimental studies, are taken into consideration, and a discrete reinforcing steel derived using the equivalent nodal force concept is also used to simulate the cracking behavior of RC walls. In advance, to Predict the crack spacing and maximum crack width in a base restrained RC wall, an analytical model which can simulate the post-cracking behavior of an RC tension member is introduced on the basis of the energy equilibrium before and after cracking of concrete.

• Computational Structural Engineering
• /
• v.2 no.2
• /
• pp.73-83
• /
• 1989

A computer program, MSSLL, was developed for the analysis of the "Multiple Shell Subjected to Lateral Loads" by utilizing 2-dimensional finite elements in a 3-dimensional global assemblage with 6 DOF at each nodal point. In this program, substructuring procedure with frontal solver was introduced in the solution procedure to save both human and computer resource when the whole structure consists of repeated identical substructures. Some of the results obtained by MSSLL were compared with the existing solutions by other methods. The effect of rise to span-length ratio was investigated for the behavior of the multiple conical shell with 8 substructures subjected to seismic loads by performing a parametric study.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.1
• /
• pp.21-29
• /
• 2001

주차장, 버스터미널, 스타디움, 집회공간과 같은 낮은 고유진동수를 갖는 장경간 건축물에서는 저속 차량의 이동하중이나 보행자의 보행하중과 같은 동적하중에 의해 과도한 바닥판 진동이 발생할 수 있으며 이러한 진동은 건축물의 이용자에게 불쾌감을 일으켜 건축물의 사용성에 심각한 영향을 주게된다. 구조물에 가해지는 보행하중의 일반적인 적용방법은 분할된 요소의 절점을 따라 절점하중으로 가하는 것이다. 그러나 이러한 해석모델은 보행하중을 절점에만 가해야하는 제한적인 문제점을 가지고 있어 보폭 수만큼 절점을 생성시켜야 하며 보폭이 변하거나 절점이외에 하중이 작용할 경우 해석모델을 수정해야하는 번거로움이 있다. 본 연구에서는 보행하중에 대한 계측과 분석을 통하여 보행하중의 동적특성을 분석하였으며 계측한 보행하중을 예제구조물에 적용하였다. 그리고 보행하중에 의한 구조물 진동의 효율적인 해석을 위하여 구조물에 가해지는 보행하중을 등가의 절점하중으로 치환하는 방법을 제안하였으며 제안된 등가절점 하중의 타당성을 검증하기 위하여 예제구조물의 진동해석을 수행하였다.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1053-1057
• /
• 2004

This paper presents the adjoint variable design sensitivity analysis for thermal systems considering both conduction and convection heat transfer. Both nodal temperature and total heat flow are considered to be objective functions and design sensitivity formulas are derived for each case. For the case of convection heat transfer, the adjoint analysis is carefully proceeded to obtain a precise result. A topology optimization example is examined for a simple planar square plate in order to design a heat exchanger as verification.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.3
• /
• pp.21-26
• /
• 2009

The finite element analysis of metal forming processes often fails because of severe mesh distortion at large deformation. As the concept of meshless methods, only nodal point data are used for modeling and solving. As the main feature of these methods, the domain of the problem is represented by a set of nodes, and a finite element mesh is unnecessary. This computational methods reduces time-consuming model generation and refinement effort. It provides a higher rate of convergence than the conventional finite element methods. The displacement shape functions are constructed by the reproducing kernel approximation that satisfies consistency conditions. In this research, A meshless method approach based on the reproducing kernel particle method (RKPM) is applied with metal forming analysis. Numerical examples are analyzed to verify the performance of meshless method for metal forming analysis.