• Transactions of the Korean hydrogen and new energy society
• /
• v.35 no.3
• /
• pp.336-344
• /
• 2024

In this study, a Ni_0.9Co_0.05Mn_0.05(OH)₂ precursor used as an anode active material using a black powder leaching solution of a recycled lithium ion battery was prepared through coprecipitation synthesis with co-precipitation time, NH₄OH concentration, pH, and stirring time as variables. The characteristics of the prepared powder were analyzed by X-ray diffraction (XRD), scanning electron microscope (SEM), particle size analysis (PSA), and inductively coupled plasma optical emission spectroscopy (ICP-OES). It was confirmed that the single crystal thickness of the LiNi_1-x-yCo_xMn_yO₂ (NCM) precursor changes depending on the NH₄OH concentration and reaction pH value, and thicker single crystals are formed at 2 M NH₄OH compared to 1 M and at pH 10.8-11.8 compared to pH 11.8-12.0. NCM precursor particles increased with coprecipitation time, and it was confirmed that the 72 hours NCM precursor had the largest particle size. Through ICP-OES analysis, it was confirmed that the NCM precursor was synthesized with the target composition of Ni²⁺:Co²⁺:Mn²⁺=90:5:5.

• Journal of the Korean Electrochemical Society
• /
• v.23 no.4
• /
• pp.105-112
• /
• 2020

Transition metal oxide, which undergoes a conversion reaction in the negative electrode material for a lithium-ion batteries, has a high specific capacity, but still has several critical problems. In this study, manganese pyrophosphate (Mn₂P₂O₇), nickel pyrophosphate (Ni₂P₂O₇), and carbon composite materials with pyrophosphates as novel negative electrode materials instead of transition metal oxide, are synthesized through simple solid-state reaction. The initial reversible capacity of Mn₂P₂O₇ and Ni₂P₂O₇ are 333 and 340 mAh g^-1, and when the composite materials are composed with carbon, the reversible capacity increases to 433 and 387 mAh g^-1, respectively. The initial Coulombic efficiency is also improved by about 10%. The Mn₂P₂O₇ and carbon composite material has the highest initial capacity and efficiency, and has the best cycle performance. Mn₂P₂O₇ containing polyanion, has a lower specific capacity due to the large mass of polyanion compared to MnO (manganese oxide). However, since Mn₂P₂O₇ shows a voltage curve with a slope, the charging (lithiation) voltage increases from 0.51 to 0.57 V (vs. Li/Li⁺), and the discharge (delithiation) voltage decreases from 1.15 to 1.01 V (vs. Li/Li⁺). Therefore, the voltage efficiency of the cell is improved because the voltage difference between charging and discharging is greatly reduced from 0.64 to 0.44 V, and the operating voltage of the full cell increases because the negative electrode potential is lowered during the discharging process.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.2
• /
• pp.102-105
• /
• 2009

The accelerated life time test of the MLCCs with different $BaTiO_3$ particle sizes were conducted at $150^{\circ}C$, 75 V condition and the effect of $BaTiO_3$ particle size on the breakdown voltage and degradation characteristics of MLCCs was investigated. The MLCCs were prepared by using the $BaTiO_3$ particles having the size of $0.525{\mu}m$, $0.555{\mu}m$, $0.580{\mu}m$ and Ni-electrode, respectively. The MLCCs which have the particle size of $0.525{\mu}m$, $0.555{\mu}m$, and $0.580{\mu}m$, respectively were confirmed to meet the standard requirements of X5R(change capacitance within ${\pm}15%$ at $-55{\sim}85^{\circ}C$) by TCC(Temperature Coefficient of Capacitance). The effect of the $BaTiO_3$ particle size on the insulation resistance behavior of MLCCs was confirmed by BDV(Breakdown Voltage) measurements and the cause and degree of degradation of MLCCs were characterized by XPS analysis after the accelerated life test. The MLCCs with $0.525{\mu}m-BaTiO_3$ showed better insulation resistance and BDV characteristics compare to other MLCCs and XPS analysis revealed that the MLCCs degradation is caused by the NiO peak and $BaTiO_3$ peak decrease.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.7
• /
• pp.2155-2161
• /
• 2013

Composite materials of mesoporous carbon and carbon nanotubes were synthesized using Ni, Co and Pd-loaded CMK3 via a catalytic reaction of methane and $CO_2$. The CNTs grew from the pores of the mesoporous carbon supports, and they were attached tightly to the CMK3 surface in a densely tangled shape. The CNT/CMK3 composite showed both non-graphitic mesoporous structures, and graphitic characteristics originating from the MWCNTS grown in the pores of CMK3. The electrochemical properties of the materials were characterized by their electrorheological effects and cyclic voltammetry. The CNTs/CMK3 composites showed high electrical conductivity and current density. The CNT/CMK3 or KOH-modified CNT/CMK3 particles were incorporated in a PMMA matrix to improve the thermal and electrical conductivity. Even higher thermal conductivity was achieved by the addition of KOH-modified CNT/CMK3 particles.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.31-35
• /
• 2001

The phase forming ability and formation enthalpies(${\Delta}H$) of Si-M(M = Ti, Cu, Ni, Zr) compound alloys were predicted by Miedema's model. The silicon compound alloys were synthesized by mechanical alloying and then characterized for the phase formation by X -ray diffraction. The electrochemical properties as the anode materials for lithium ion batteries were investigated using a galvanostatic method. It appears that the electrochemical characteristics of Si-M alloys can be predicted from the thermodynamic criteria for the phase formation using the Miedema's model.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.8
• /
• pp.685-689
• /
• 2005

In the fabrication and design of MLCCs (Multilayer Ceramic Capacitors) with Ni inner electrode for medium and high voltage, reliability and dielectric breakdown mode have been investigated. For thickness of green sheet, the relationship between the rated voltage versus the thickness of green sheet. Increasing the thickness of green sheet increases the dielectric breakdown voltage. However, a practical limit to this linear relationship occurs at 30 urn and above. As the thickness of green sheet increased, dielectric breakdown voltage and weibull coefficient is increased, but abruptly decrease at 30 urn and 36 urn. When 24 urn of green sheet thickness, weibull coefficient and dielectric breakdown voltage were 13.58 and 70 V/um respectively. The results enabling the MLCCs to demonstrate high levels of reliability at medium and high voltage.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.1
• /
• pp.1-7
• /
• 1999

In order to study on the effect of fabrication methods on the changes of hydrogenation properties of FeTi alloy, FeTi samples were prepared using three different methods, i.e., arc melting, mechanical alloying and combination of the two methods. The FeTi prepared by mechanical alloying represented amorphous structure. The hydrogen storage capacity of arc melted FeTi alloy is larger than any other samples. However, FeTi electrode fabricated by mechanical alloying after arc melting showed largest discharge capacity among them.

• Journal of Sensor Science and Technology
• /
• v.21 no.6
• /
• pp.425-428
• /
• 2012

This paper presents the fabrication and characterization of graphene based hydrogen sensors. Graphene was synthesized by annealing process of Ni/3C-SiC thin films. Graphene was transferred onto oxidized Si substrates for fabrication of chemiresistive type hydrogen sensors. Au electrode on the graphene shows ohmic contact and the resistance is changed with hydrogen concentration. Nanoparticle catalysts of Pd and Pt were decorated. Response factor and response (recovery) time of hydrogen sensors based on the graphene are improved with catalysts. The response factors of pure graphene, Pt and Pd doped graphenes are 0.28, 0.6 and 1.26, respectively, at 50 ppm hydrogen concentration.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.140-140
• /
• 2003

Ti:LiNbO$_3$ 광 도파로를 이용한 광 변조기의 마이크로파 손실을 감소시키고 RF와 광파의 속도정합의 조건하에서 초고속 광변조의 제작을 위해서는 두꺼운 TW(travelling wave) 전극이 필수적이다 또한, 두꺼운 Au 전극이 우수한 RF 특성을 갖기 위해서는 도금된 Au 전극이 고순도의 작은 grain size를 갖는 도금 층을 제조하여야 하며, 도금 후 Au 층의 뒤틀림 현상이 작아야 한다. 따라서, 본 연구에서는 LiNbO$_3$ 기판 위에 30nm Ni-Cr과 50nm의 Au의 기저 막을 올렸으며 감광제를 이용한 photo-lithography 공정으로 CPW(coplanar waveguide) 구조의 패턴을 약 13$\mu\textrm{m}$의 두께로 형성 한 후 non-cyanidic 액을 이용하여 전류밀도 0.02 - 0.06 mA, bubble 및 non-bubble flow를 조건으로 하여 도금된 Au 전극의 특성을 관찰하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.10
• /
• pp.911-915
• /
• 2008

EL (electro-luminescent) device as a light source has an advantage in embodying large area with great flexibility. On nickel foil as an electrode and backplane, we demonstrated a white EL flexible light source with blue phosphor layer combined with color change layer. A correlation between color change layer and color coordination was analyzed by Gaussian method, and then the color coordinate was controlled near to (0.33, 0.33) of pure white light.