• Membrane Journal
• /
• v.18 no.2
• /
• pp.157-167
• /
• 2008

Removal of organic substances and taste/odor control are ones of the main issues in water supply, resulting in introduction of advanced processes such as ozon/GAC, or PAC. However, raw water quality deteriorates, new pollutants advent, so water quality is not acceptable enough even with those existing advanced processes. In this paper, a new advanced water treatment process using PAC slurry blanket, where PAC particles stay in the basin as slurry blanket, coupled with submerged membranes is introduced. A pilot plant $(80m^3/day)$ was installed to assess the performance of this new process using actual raw water, and DOC was removed higher than 90% in the beginning and $70{\sim}80%$ afterwards, while 2-MIB and geosmin were removed completely. This new process still requires future study on process optimization and long-term assessment, however it seems highly possible to countermeasure as a new advanced process with high removal efficiency.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.80-89
• /
• 2006

The rapid development of process technology and the introduction of new materials not only make it difficult for process control but also as a result increase process variations. These process variations are barriers to successful implementation of design circuits because there are disparities between data on layout and that on wafer. This paper proposes a new design environment to determine the interconnect worstcase with accuracy and speed so that the interconnect effects due to process-induced variations can be applied to designs of $0.13{\mu}m$ and below. Common Geometry and Maximum Probability methods have been developed and integrated into the new worstcase optimization algorithm. The delay time of the 31-stage Ring Oscillator, manufactured in UMC $0.13{\mu}m$ Logic, was measured, and the results proved the accuracy of the algorithm. When the algorithm was used to optimize worstcase determination, the relative error was less than 1.00%, two times more accurate than the conventional methods. Furthermore, the new worstcase design environment improved optimization speed by 32.01% compared to that of conventional worstcase optimizers. Moreover, the new worstcitse design environment accurately predicted the worstcase of non-normal distribution which conventional methods cannot do well.

• Korean Journal of Materials Research
• /
• v.22 no.5
• /
• pp.227-236
• /
• 2012

Ionomer is a thermoplastic that is composed of covalent bonds and ionic bonds. It is possible to use this material in processes such as injection molding or extrusion molding due to the material's high oil resistance, weatherproof characteristics, and shock resistance. In this study, a new ionomer having a multifunctional group was prepared by a stepwise neutralization system with the addition of acidic and salt additives. In step I, to increase the contents of the multifunctional group and the acid degree in ethylene acrylic acid (EAA), MGA was added to the ionomer resin (EAA). A new ionomer was prepared via the traditional preparation method of the ionic cross-linking process. In step II, metal salt was added to the mixture of EAA and MGA. The extrusion process was performed using a twin extruder (L/D = 40, size : ${\varphi}30$). Ionomer film was prepared for evaluation of gas permeability by using the compression molding process. The degree of neutralized and ionic cross-linked new ionomer was confirmed by FT-IR and XRD analysis. In order to estimate the neutralization of the new ionomer film, various properties such as gas permeation and mechanical properties were measured. The physical strength and anti-scratch property of the new ionomer were improved with increase of the neutralization degree. The gas barrier property of the new ionomer was improved through the introduction of an ionic site. Also, the ionic degree of cross-linking and gas barrier property of the ionomer membrane prepared by stepwise neutralization were increased.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.1
• /
• pp.28-38
• /
• 2014

The organic-inorganic composite membrane in polymer exchange membrane fuel cells (PEMFCs) have several fascinating technological advantages such as a proton conductivity, thermal stability and mechanical properties. As the inorganic filler, silicon carbide (SiC) fiber have been used in various fields due to its unique properties such as thermal stability, conductivity, and tensile strength. In this study, composite membrane was successfully fabricated by modified-silicon carbide fiber. Modified process, as a novel process in SiC, takes reaction by phosphoric acid after oxidation process (generated homogeniusly $SiO_2$ layer on SiC fiber). The mechanical property which was conducted by tensile test of the 5wt% modified-$SiO_2@SiCf$ composite membrane was better than that of Aquivion casting membrane as well as ion cxchange capacity(IEC) and proton conductivity. In addition, the single cell performance was observed that the 5wt% modified-$SiO_2@SiCf$ composite membrane was approximately $0.2A/cm^2$ higher than that of a Aquivion casting electrolyte membrane and electrochemical impedance was improved with the charge transfer resistance and membrane resistance.

• Hwankyungkyoyuk
• /
• v.20 no.2
• /
• pp.108-122
• /
• 2007

Recently, a new revised national curriculum('2007 Revised') of the 'Environment' subject for middle and high schools was announced, which is namely the 7th revised national curriculum. In the new national curriculum, the name of the 'environment' subject for middle schools has been unchanged, but the name of the subject for high schools has been changed from the 'Ecosystem & Environment' to 'Environment'. And some of the contents have been revised to incorporate the changed status of environmental education areas since the last announcement of the 'Environment' curriculum, which was in the late of 1997. Especially, in this new curriculum, the concept of the 'Education for Sustainable Development (ESD)' was implemented. The purpose of this research is to investigate the process of developing the new 'Environment' curriculum for middle and high schools and to examine the resulted, new revised curriculum. In order to do these, this research examined the main directions of the revision, compared the new announced curriculum with the current and the proposed one, which was researched by the authors in this article. And this research discussed the process and the announced results of the revised national curriculum of the 'Environment' subject.

• Membrane and Water Treatment
• /
• v.8 no.4
• /
• pp.311-321
• /
• 2017

Hydrophilic and high modulus PPTA molecules were incorporated into PVDF matrix via the in situ polymerization of PPD and TPC in PVDF solution. PPTA/PVDF/NWF blend membrane was prepared through the immersion precipitation phase inversion method and nonwoven coating technique. The membrane integrated technology including PPTA/PVDF/NWF blend membrane and reverse osmosis (RO) membrane was employed to treat the polyester/viscose spunlace nonwoven process wastewater. During the consecutive running of six months, the effects of membrane integrated technology on the COD, ammonia nitrogen, suspended substance and pH value of water were studied. The results showed that the removal rate of COD, ammonia nitrogen and suspended substance filtered by PPTA/PVDF blend membrane was kept above 90%. The pH value of the permeate water was about 7.1 and the relative water flux of blend membrane remained above 90%. After the deep treatment of RO membrane, the permeate water quality can meet the water circulation requirement of spunlace process.

• Journal of Korea Multimedia Society
• /
• v.17 no.11
• /
• pp.1307-1312
• /
• 2014

Online games are virtual space where it connects individual users through network connection to offer enjoyment of play games and game developer who service online games have to develop new contents and provide them to users to extend life of their service. Typically, in order to update new contents, all service companies have maintenance schedule to stop the game service for a while to update both server and client applications. Usually this process takes quite amount of time and users do not have any other choice but disconnected from server and wait until it is over. The purpose of this thesis is to describe the advantages of new design system which will allows users to continue to play the game even during the update. The main focus of this design is to make users feel more convenience in online gaming experience by move client from previous server to new server while users are still playing. If they can to connect current client with new server without any certificate validation process while users information from the client can automatically pass through to the new server, users may not need to experience maintenance for new contents update.

• Journal of Intelligence and Information Systems
• /
• v.8 no.1
• /
• pp.159-173
• /
• 2002

The goal of this research is to develop of an intelligent injection mold process planning system using Case-Based Reasoning. Injection mold process planning is the planning of manufacturing process to produce an injection mold economically and efficiently. Automation of the process planning is required because the problems of handmade scheduling, the difficulty of training experts for process planning, the lack of domain experts, the spread of CAD/CAM system and flexible manufacturing. This research uses Case-Based Reasoning because the injection mold process planning is devised variously and complicatedly, but the process planning of similar injection molds is very similar to each other. The system that is developed by this research uses cases that are collected in a case base when planning the process of new injection mold. New injection mold process planning is devised by retrieving a case that was made from the most similar injection mold. This research presented and composed the cases of injection mold process planning, and devised a method of search and adaptation, and developed an intelligent injection mold process planning system with the experimental results.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.1
• /
• pp.41-49
• /
• 2017

Process quality control, which prevents problems and risks that may occur in products and processes, has been recognized as an important issue, and SPC techniques have been used for this purpose. Process Capability Index (PCI) is useful Statistical Process Control (SPC) tool that is measure of process diagnostic and assessment tools widely use in industrial field. It has advantage of easy to calculate and easy to use in the field. $C_p$ and $C_{pk}$ are traditional PCIs. These traditional $C_p$ and $C_{pk}$ were used only as a measure of process capability, taking into account the quality variance or the bias of the process mean. These are not given information about the characteristic value does not match the target value of the process and this has the disadvantage that it is difficult to assess the economic losses that may arise in the enterprise. Studies of this process capability index by many scholars actively for supplement of its disadvantage. These studies to evaluate the capability of situation of various field has presented a new process capability index. $C_{pm}$ is considers both the process variation and the process deviation from target value. And $C_{pm}{^+}$ is considers economic loss for the process deviation from target value. In this paper we developed an improved Expected Loss Capability Index using Reflected Normal Loss Function of Spring. This has the advantage that it is easy to realistically reflect the loss when the specification is asymmetric around the target value. And check the correlation between existing traditional process capability index ($C_{pk}$) and new one. Finally, we propose the criteria for classification about developed process capability index.

• Journal of the Korean Institute of Rural Architecture
• /
• v.1 no.2
• /
• pp.97-108
• /
• 1999

There are so many theories and arguments on the architectural design process. However, in the time of the environmental preservation, there is the need for the introduction of the systematic green design process because no existing design process theories could give the rational design tool far the integrated design with environmental factors. This study, through the literature survey, is on the new paradigm for the systematic approach to the integrated process of 'the Green Design'.