• 전자공학회논문지
• /
• 제51권2호
• /
• pp.207-213
• /
• 2014

본 논문에서는 임펄스 잡음을 제거하는 수정된 미디언 필터를 제안한다. 다단계를 기반으로 하는 제안 방법은 먼저 잡음 영상에서 잡음과 화소를 분리하고 잡음으로 판단된 화소를 미디언 필터링한다. 이때 필터링에 사용하는 주변 화소들을 에지에 따라 방향을 조절하여 필터링하는 선형필터링 한 값으로 대체한다. 따라서 제안하는 방법은 에지를 유지할 뿐 아니라 일정한 지역에서 잡음을 효과적으로 제거한다. 실험결과, 제안하는 방법이 기존 수정된 미디언 필터 보다 향상된 결과를 보인다.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2001년도 학술대회 논문집
• /
• pp.84-88
• /
• 2001

The optimum cross-sectional area Profile of gas-cooled high-temperature superconductor (HTS) current lead is analyzed to have minimum helium boil-off rate. The conventional constant area HTS lead has much higher helium consumption than the optimum HTS lead considered in this study. The optimum HTS lead has variable cross-sectional area to have constant safety factor. An analytical formula of optimum shape of lead and temperature profile are obtained. For multi-step HTS current leads, the optimum tape lengths and minimum heat dissipation rate are also formulated. The developed formulations are applied to the Bi-2223 material, and the differences between constant area, constant safety-factor, and multi-step current leads are discussed.

• 대한기계학회논문집A
• /
• 제24권10호
• /
• pp.2451-2460
• /
• 2000

In order to minimize straightness error of deflected shaft, a geometric adaptive straightness controller system is studied. A multi-step straightening and a three-point bending process have been developed for the geometric adaptive straightness controller. Load-deflection relationship, on-line identification of variations of material properties, on-line springback prediction, and real-time hydraulic control methodology are studied for the three-point bending process. By deflection pattern analysis and fuzzy self-learning method in the multi-step straightening process, a straightening point and direction, desired permanent deflection and supporting condition are determined. An automatic straightening machine has been fabricated for rack bars by using the developed ideas. Validity of the proposed system is verified through experiments.

• 대한전자공학회논문지
• /
• 제24권6호
• /
• pp.1074-1079
• /
• 1987

We present a fast, constructive algorithm for the automatic placement of standard cells, which consists of two steps. The first step is responsible for cell-row assignment of each cell, and converts the circuit connectivity into a multi-stage graph under to constraint that sum of the cell-widths in each stage of the multi-state graph does not exceed maximum cell-row width. Generatin of feed-through cells in the final layout was shown to be drastically reduced by this step. In the second step, the position of each cell within the row is determined one by one from left to right so that the cost function such as the local channel density is minimized. Our experimental result shows that this algorithm yields near optimal results in terms of the number of feed-through cells and the horizontal tracks, while running about 100 times faster than other iterative procedures such as pairwise interchange and generalized force directed relaxation method.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.144-147
• /
• 1997

Process design of multi-step wire drawing process, conducted by means of finite element analysis and ANN(Artificial Neural Network), has been considered. The investigated problem involves the adequate selection of the drawing die angle and the correspondent reduction rate sequence in the condition of desired initial and final diameter. Combinations of the process parameters which are used in finite element simulation are selected by using orthogonal array. Also the orthogonal array and the results of finite element simulation which are related to the process energy are used as train data of ANN. In this study, it is shown that the new technique using ANN is useful method in application to the wide range of metal forming process.

• 응용통계연구
• /
• 제23권2호
• /
• pp.357-366
• /
• 2010

Many tree algorithms have been developed for regression problems. Although they are regarded as good algorithms, most of them suffer from loss of prediction accuracy when there are many noise variables. To handle this problem, we propose the multi-step GUIDE, which is a regression tree algorithm with a variable selection process. The multi-step GUIDE performs better than some of the well-known algorithms such as Random Forest and MARS. The results based on simulation study shows that the multi-step GUIDE outperforms other algorithms in terms of variable selection and prediction accuracy. It generally selects the important variables correctly with relatively few noise variables and eventually gives good prediction accuracy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.871-874
• /
• 2002

Many malfunctions take place in container crane spreader due to impact. So we designed a 2DOF hydraulic impact absorbing system with multi-step damping coefficient and studied the effect of orifice's interval and damping coefficient. The damping coefficient of upper piston was found to be 180 N.s/m, and the orifice's interval to be 9mm, the max reaction force and the average reaction force might be lowest. Compared with a general 2-DOF impact absorbing system, the max reaction force reduced by 46%., and average reaction force reduced by 5%.

• Transactions on Electrical and Electronic Materials
• /
• 제3권4호
• /
• pp.27-31
• /
• 2002

Thin film diode with reliable interfacial structure was fabricated by using multi-step anodic oxidation. The thickness of the oxide layer was preciously controlled with anodic voltage. Also, interfacial structure between oxide layer and top electrode was improved by applying post heat-treatment. The thin film diode showed symmetric and stable I-V characteristics after the post heat-treatment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.155-158
• /
• 1999

Because the traditional filters have many demerits, multi-step electric oil filter have manufactured the efficiency of insulating oil to improve. Therefore, the function of oil filter to improve based on my experience and know-how about my job. Through this study have obtained many merits. The efficiency of insulating oil is improved. The waste oil reused in repair works of the damaged transformer. Multi-step filter is shortening the working time and safety. it is handy for use and movement. This study lengthen the expected life span of filter. The improvement of oil filter bring about elevation of productivity.

• International Journal of Precision Engineering and Manufacturing
• /
• 제2권2호
• /
• pp.65-72
• /
• 2001

The design of multi-stage gear drives is a time-consuming process, since on includes more complicated problems, which are not considered in the design of single-stage gear drives. The designer has th determine the number of reduction stages and the gear ratios of each reduction state. In addition, the design problems include not only the dimensional design but also the configuration design of gear drive elements. There is no definite rule and principle for these types of design problems. Thus the design practices largely depend on the sense and the experiences of the designer , and consequently result in undesirable design solution. We propose a new generalized design algorithm to support the designer at the preliminary design phase of multi-stage gear drives. The proposed design algorithm automates the design process by integrating the dimensional design and the configuration design process. The algorithm consists of four steps. In the first step, a designer determines the number of reduction stage. In the second step. gear ratios se chosen by using the random search method. In the third step, the values of basic design parameter are chosen by using the generate and test method. Then, the values of other dimension, such ad pitch diameter, outer diameter, and face width, are calculated for the configuration design in the final step. The strength and durability of a gear is guaranteed by the bending strength and the pitting resistance rating practices by using the AGMA rating formulas. In the final step, the configuration design is carried out b using the simulated annealing algorithm. The positions of gears and shafts are determined to minimize the geometrical volume(size) of a gearbox, while satisfying spatial constraints between them. These steps are carried out iteratively until a desirable solution is acquired. The propose design algorithm has been applied to the preliminary design of four-stage gear drives in order to validate the availability. The design solution have shown considerably good results in both aspects of the dimensional and the configuration design.