• 오토저널
• /
• 제10권6호
• /
• pp.39-47
• /
• 1988

A disk photo sensor system was constructed and installed on engine for the crank angle measurement. Statically measured TDC crank angle data were compared with those obtained from engine motoring. Two groups of cylinder pressure data were compared each other, one measured by pressure transducer mounted flush on the combustion chamber and the other obtained with the help of spark plug type adaptor. A simple analysis on the gas flow in the spark plug type pressure transducer displayed reasonably good agreement with those from engine motoring tests. In various firing tests, the IMERs obtained from the spark plug type pressure transducer turned out to be higher than those from the flush mounted one at low engine speed while those two were nearly the same at high engine speed. As the engine load decreased the relative difference in IMEP measurement between the two types tended to be enlarged.

• 전기학회논문지
• /
• 제58권10호
• /
• pp.2028-2037
• /
• 2009

This paper presents the simulator for dynamic modeling of a MT(micro turbine) during start-up period. The simulator is implemented by modeling a dynamic power of main components of a MT including compressor, combustor and turbine. A modeling for a MT under steady state operation can be accurately built from thermodynamics analysis. But dynamic modeling during start-up period is very difficult because efficiency of main components is very low and the designed value has big error and nonlinear characteristics during start-up. In this paper, new method without using thermodynamics analysis during start-up is proposed for the simulator. The power models of main components are derived from analysis of the experimental operation data by test motoring using a electric starter under constant power output. The simulator is developed using MATLAB/Simulink. For constant power output control, sensorless vector inverter is designed and algorithms for starting from stall and method for controling a output power are proposed. The performance of developed simulator is verified by comparing experimental and simulation start-up results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전력기술부문
• /
• pp.378-380
• /
• 2006

Loss of excitation, over excitation and motoring of generator are simulated by using synchronous generator with an exciter and a governor. This paper presents an analysis of transient state of generator and protection relay operation with loss of excitation. over excitation and motoring of generator.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.31-38
• /
• 2006

Cylinder liner rotation is a new concept for reducing piston assembly friction in the internal combustion engine. The purpose of cylinder liner rotation is to reduce the occurrence of boundary and mixed lubrication friction in the piston assembly. This paper reports the results of experiments to quantify the potential of the rotating liner engine. A GM Quad-4 SI engine was converted to single cylinder operation and modified for cylinder liner rotation. The hot motoring method was used to compare the friction loss between the baseline engine and the rotating liner engine. Additionally, tear-down tests were used to measure the contribution of each engine component to the total friction torque. The cycle-averaged motoring torque of the RLE represents a $23\~31\%$ friction reduction compared to the baseline engine for hot motoring tests. Through tear down tests, it was found that the piston assembly friction of the baseline engine is reduced from $90\%$ at 1200 rpm to $71\%$ at 2000 rpm through liner rotation.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.45-50
• /
• 2011

Compression pressure of individual cylinder and valve timing have big influence on combustion pressure, indicated mean effective pressure (IMEP), emission, vibration, combustion noise and many other combustion parameters. Conventional method, however, to check compression pressure uniformity is done by mechanical pressure gage and valve timing is checked manually. This conventional method causes inaccuracy of cylinder pressure measurement because of different cranking speed results from battery status and temperature. Also to check valve timing, related FEAD parts should be disassembled and timing mark should be checked. This study describes and suggests new methodology to measure compression pressure by analysis of start motor current and to check valve timing by cylinder pressure with high accuracy. Results, it is found that detection of bulky as well as small leaky cylinder is possible by cranking motor current analysis and wrong valve timing can be detected by cylinder pressure analysis and cam and crank sensor signal.

• 석유와에너지
• /
• 9호통권55호
• /
• pp.79-85
• /
• 1985

이 자료는 영국 BP사의 Briefing Paper 1985년 7월호에 게재된 「Fuels for motoring : trends in automotive fuels 」를 번역 정리한 것이다 <역자주>

• 전기학회논문지P
• /
• 제63권3호
• /
• pp.149-156
• /
• 2014

Generator of hydroelectric generating unit is to be protected by the digital protection IED. Now, any IED of large capacity for hydro power plant was not developed by domestic technology. This is because it is required for the generator of the high reliability technology and considered as due to the sale of the market of IED device is small. However, the protection IED must be develop by domestic technology to meet the advanced needs of the construction and replacement of electrical equipment in accordance with the new power plant development. In this paper, a digital algorithms for protection IED of large size of hydroelectric generating unit were designed. The algorithms consist of the stator protection, anti-motoring, overexcitation and loss of excitation. The performance of the algorithms were evaluated by using the simulation data collected from the PSCAD/EMTDC software. From test results, it can be seen that the developed algorithms were not maloperation.

• 오토저널
• /
• 제14권3호
• /
• pp.80-89
• /
• 1992

An experimental study of in-cylinder of flow and combustion characteristics in two gasoline engines of different intake ports which are denoted as original port and masked shroud head (MSH) ports is presented. The flows generated by the MSH and the original port are invest- igated by laser Doppler velocimeter(LDV) under steady flow and motoring (non-firing) condit -ions. Combustion characteristics with different swirl levels produced by two intake ports are analyzed by combustion pressure measurement and statistical calculation. The swirl inside the cylinder of the MSH port engine is found to be much higher than the original port, and the MSH has a large eddy motion of cylinder diameter size. Using ensemble average method to valuate engine turbulence under motoring condition, the MSH port engine is shown to have h -igher turbulence intensity than the original port, so that the effect of the MSH port on fast burn is shown. Also the cyclic variations of peak pressure and the reaching time in the MSH port are apparently reduced.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2000년도 춘계종합학술대회
• /
• pp.398-401
• /
• 2000

This paper describes the standardization of remote monitoring and controlling system for nursery electrical facilities. The proposed system have three operating modes of motoring, controlling, and fault-notifying. In fault-notifying mode, the local unit is designed to send messages on failure of the electrical facilities to the central computer, mobile phone, and pager. Also, the local unit is consisted of 24-input and 8-output port needed for monitoring and controlling the facilities. With the use of this standardized system, we could expect the effective management in every phase of nursery facilities.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.184-189
• /
• 1999

This Paper presents the friction and lubrication charateristic related with oil aeration. It is well known that oil aeration occurs severe problem on lubrication system, in particular, in the engine bearings and hydraulic lash adjuster. In this study, engine tests were carried out in motoring conditions. In order to investigate oil aeration characteristics, we measured oil aeration with respect to oil temperature, oil viscosity, modified oil drain system. From the results, we concluded that aeration can be reduced by improving oil drain system and FMEP can be reduced by minimising of aeration.