• Journal of the Korean Wood Science and Technology
• /
• 제25권4호
• /
• pp.29-38
• /
• 1997

The effect and control of wood property of reconstituted composite panels for improved board properties by wood-waste materials and development of combination method for heterogeneous materials have been of interest to the wood science researchers. The purpose of this study is to consider the properties in relation to hot pressing conditions and to develope the optimum hot pressing condition with waste wood and waste tire for the manufacturing of composite boards. The study of composite boards for recycling of wood and waste tire is nothing up to the present. Physical and mechanical properties such as specific gravity, moisture content, swelling coefficient, modulus of rupture and modulus of elasticity in bending test were studied. The condition of 3-stage press time for the lowest moisture content of composite board was $4{\rightarrow}3{\rightarrow}3$ minutes. Specific gravity of composite panels was affected mainly by the amount of rubber chip. Because of the low rigidity and high elasticity in rubber chip, it is considered the composite panel was adequate material in the place of compression load, but not bending load. Therefore, it was concluded that a use of rubber-based wood composite panel is proper to the interior materials such as floor a room than exterior materials. From the test results, the most optimum hot pressing conditions were $4{\rightarrow}3{\rightarrow}3$ minutes for 3-stage press time and $45{\rightarrow}20{\rightarrow}5kg/cm^2$ for 3-stage press pressure. The rubber-based wood composite panel was very excellent in elasticity by combination of rubber chip in comparison with existing other wood-based materials. Therefore, it was considered that rubber-based wood composites can be applicable to every interior materials such as floor a room and will be expected to effective reuse and recycle of waste tires and wood-waste materials, and will be contribute to protection of environment pollution in earth.

• Restorative Dentistry and Endodontics
• /
• 제34권2호
• /
• pp.145-153
• /
• 2009

본 연구에서는 측정장치의 compliance유무가 복합레진의 중합수축응력 측정에 미치는 영향을 알아보았다. 변위센서, cantilever load cell과 부궤환 (negative feedback) 시스템을 적용하여 compliance를 허용하는 것과 허용하지 않는 두 가지 모드로 중합수축응력의 측정이 가능한 stress-strain analyzer를 제작하였다. 한 종의 flowable (Filtek Flow: FF) 복합레진과 두 종의 universal hybrid (Z100: Z1 and Z250: Z2) 복합레진이 사용되었다. Load cell의 끝과 base plate에 고정된 직경 3.0 mm의 금속 막대에 silane을 처리하였다. 1.0 mm의 거리로 고정한 두 개의 금속 막대 사이 에 복합레진을 적용한 후 광중합을 하였다. 복합레진의 수직 중합수축률과 중합수축응력을 10 분 동안 기록하였고 인장탄성계수도 구하였다. 통계처리는 일원분산분석과 paired t-test를 시행하였고 95% 유의수준에서 Tukey's test로 사후 검정하였다. 측정된 중합수축 응력은 재료와 compliance의 유무에 따라 큰 차이를 보였다. Compliance를 허용한 모드에서 중합수축응력은 FF: 3.11 (0.13)이 가장 컸으며 Z1: 2.91 (0.10), Z2: 1.94 (0.09) Mpa의 순서였다. 측정장치의 compliance를 허용하지 않은 경우에는 Z1 17.08 (0.89)이 가장 컸고 FF: 10.11 (0.29), Z2: 9.46 (1.63) MPa의 순이었다. 또한 Z1, Z2, FF의 인장탄성계수는 각각 2.31 (0.18), 2.05 (0.20), 1.41 (0.11) GPa 이었다. 중합수축응력은 compliance mode에서는 복합레진의 수직 중합수축률이 주요 영향 요인이었으며, compliance를 배제한 모드에서는 탄성계수의 효과가 지배적이었다.

• 대한기계학회논문집A
• /
• 제32권2호
• /
• pp.105-118
• /
• 2008

The newly developed analysis method for nanoindentation load-displacement curves are focused on not only obtaining elastic modulus and hardness values but also other mechanical properties, such as yield strength and strain hardening properties. Dao et al. developed a forward and reverse algorithm to extract the elasto-plastic properties of materials from the load-displacement curves obtained in nanoindentation test. These algorithms were only applicable for engineering metals (Poisson#s ratio 0.3) using the equivalent conical indenter of the Berkovich. However, the applicable metals are substantially limited because range of used in the finite element analysis is narrow. This study is designed to expand range of the applicable metals in the reverse algorithms established by Dao et al. and to improve the accuracy of that for extracting the elasto-plastic properties of materials. In this study, a representative strain was assumed to vary according to specific range of $E^*/{\sigma}_r$ and was defined as function of $E^*/{\sigma}_r$. Also, an initial unloading slope in reverse algorithms improved in this study was not considered as independent parameters of the load-displacement curves. The mechanical properties of materials for finite element analysis were modeled with the elastic modulus, E, the yield strength, ${\sigma}_y$, and the strain hardening exponents, n. We showed that the representative strain (0.033) suggested by Dao et al. was no longer applicable above the $E^*/{\sigma}_r$ of 400 and depended on values of $E^*/{\sigma}_r$. From these results, we constructed the dimensionless functions, in where the initial unloading slope was not included, for engineering metals up to $E^*/{\sigma}_r$ of 1500. These functions allow us to determine the mechanical properties with greater accuracy than Dao#s study.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2003년도 학술발표논문집
• /
• pp.367-370
• /
• 2003

Lightweight polymer concrete with steel fiber can be used for thin panel, high building and large span structures due to its may advantages such as its durability, low weight, control of crack propagation, high strength and toughness. This study experimented about steel fiber reinforcement of lightweight polymer concrete using synthetic lightweight aggregate. The test result shows that the maximum strain and elastic modulus are in the range of $0.012{\sim}0.014\;and\;50.2{\times}10^3{\sim}51.0{\times}10^3kgf/cm^2$, respectively. The flexural load-deflection curves after maximum load are shown in smoothly with increase of steel fiber content

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1-6
• /
• 2008

Due to the self-similarity of Berkovich and conical indenters, different materials may show the same loaddepth curve for single indentation. In this study, we first compare the load-depth characteristics of conical and Berkovich indenters via finite element method. We also analyze the variation of load-depth curves with angle of Berkovich indenter, indentation parameters, and material properties. With numerical regressions of obtained data, we then propose dual-Berkovich indentation formulae for material property evaluation. The proposed approach provides the values of elastic modulus, yield strength and strain-hardening exponent and corresponding stress-strain curve with an average error of less than 3%. The method is valid for any elastic indenters made of tungsten carbide and diamond for instance.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.977-986
• /
• 2009

Sampling disturbance can introduce considerable errors in the laboratory estimation of geotechnical properties of soils, and the results obtained from sophisticated sampling and careful laboratory testing are not matching with field behavior. Therefore, it is advantage to adopt in-situ testing techniques for the estimation of geotechnical parameters. Therefore, Screw plate loading test, one of new field test technologies, has been investigated in this study. This test can be utilized to find out important properties of soils such as load-displacement, elastic modulus, and shear strength. The screw plate loading test modified from the plate loading test is an experiment underneath ground by inserting a spiral type of auger screw. The structure and characteristics of the screw plate loading test device was examined in detail. In addition, The new screw plate loading test device was manufactured to refer the previous studies. The reliability of developing screw plate loading test was examined through the analysis of the laboratory test.

• 한국지반공학회지:지반
• /
• 제11권1호
• /
• pp.113-126
• /
• 1995

점성토의 변형특성을 연구하기 위하여 공진주(RC)시험과 비틀전단(75)시험을 저변형률 및 중간 변형률하에서 실시하여 변형률의 크기,진동주파수,하중반복회수의 영향을 살펴보았다. 소 성지수가 이들의 영향을 평가하는데 중요한 변수임을 알 수 있었다. 실험에 사용된 시료로는 불 교란 실트 및 점토와 실험실에서 다져진 노상토를 사용하였다. 선형한계변형률이하에서 전단탄 성계수는 하중반복회수와 변형률의 크기에 영향을 받지 않았으며, RC시험에서 얻은 최소감소비가 1.1%에서 1.7%영역에서 존재하였다. 점성토의 선형한계변형률은 구속압과 소성지수에 따라 증가하였으며 사질토와 비교하여 넘은 선형영역을 보였다. 반복한계변형률이상의 변형률하에서는 전단탄성계수는 하중반복회수에 따라 감소하였지만 감쇠비는 영향을 받지 않았다. 진동주파수의 영향에 의해 RC시험에서 얻은 점성토의 전단탄성계수와 감쇠비는 RC시험결과보다 컸다. 전단탄성계수는 진동주파수의 대수증가에 따라 선형적으로 증가하였고 감쇠비의 경우 2Hz이하의 저주파수영역에서는 영향을 받지 않았다.

• 한국도로학회논문집
• /
• 제17권6호
• /
• pp.19-26
• /
• 2015

PURPOSES : This study intends to develop an inorganic soil pavement material using industrial by-products and to evaluate its applicability as a road pavement material. METHODS : In this study, a compressive strength experiment was conducted based on the NaOH solution molarity and water glass content to understand the strength properties of the soil pavement material according to the mixing ratio of alkali activator. In addition, the strength characteristic of the inorganic soil pavement material was analyzed based on the binder content. The performance of the soil pavement was evaluated by conducing an accelerated pavement test and a falling weight deflectometer (FWD) test. RESULTS : As a result of the soil pavement material test based on the mixture ratio of alkali activator, it was identified that the activator that mixed a 10 M NaOH solution to water glass in a 5:5 ratio is appropriate. As a result of the inorganic soil pavement materials test based on the binder content, the strength development increased sharply when the amount of added binder was over 300 kg; this level of binder content satisfied 28 days of 18 MPa of compression strength, which is the standard for existing soil pavement design. According to the measured results of the FWD test, the dynamic k-value did not show a significant difference before or after the accelerated pavement testing. Furthermore, the effective modulus decreased by approximately 50%, compared with the initial effective modulus for pedestrian pavement. CONCLUSIONS : Based on these results, inorganic soil pavement can be applied by changing the mixture proportions according to the use of the pavement, and can be utilized as road pavement from light load roads to access roads.

• Geomechanics and Engineering
• /
• 제32권3호
• /
• pp.245-254
• /
• 2023

Through qualitative analysis and quantitative analysis, the contradictory conclusions about the stability of the settled goaf with two-layer coal seams subject to building load were obtained. Therefore, it is necessary to combine the additional stress method and numerical simulation to further analyze the foundation stability. Through borehole analysis and empirical formula analogy, the height of water-conducting fracture zone in No.4 coal and No.9 coal were obtained, providing the calculation range of water-conducting fracture zone for numerical simulation. To ensure the accuracy of the elastic modulus of broken gangue, the stress-strain curve were obtained by broken gangue compression test in dried state of No.4 coal seam and in soaking state of No.9 coal seam. To ensure the rationality of the numerical simulation results, the actual measured subsidence data were retrieved by numerical simulation. FISH language was used to analyze the maximum building load on the surface and determine the influence depth of building load on the foundation. The critical building load was 0.16 MPa of No.4 settled goaf and was 1.6 MPa of No.9 settled goaf. The additional stress affected the water-conducting fracture zone obviously, resulted in the subsidence of water-conducting fracture zone was greater than that of bending subsidence zone. In this paper, the additional stress method was analyzed by numerical simulation method, which can provide a new analysis method for the treatment and utilization of the settled goaf.

• 콘크리트학회논문집
• /
• 제20권5호
• /
• pp.583-592
• /
• 2008

최근 고강도콘크리트의 압축강도, 탄성계수 및 최대하중에서의 변형에 대한 고온의 영향이 실험적으로 연구되어지고 있다. 본 연구는 40, 60, 80 MPa 급 고강도콘크리트의 재료 역학적 특성에 있어서 $20{\sim}700^{\circ}C$ 범위로 상승되는 온도의 영향을 연구하는데 그 목적이 있다. 본 연구에서는 설계하중 사전재하 및 잔존강도시험 방법으로서 시험체를 가열하기 전에 상온 압축강도의 25% 하중을 사전재하한 후 가열을 실시하고, 가열하는 동안 하중을 유지하며, 목표온도에 도달한 후 고온상태 및 상온에서 24시간 냉각상태에서 시험체가 파괴될 때까지 재하를 실시하였다. 시험은 W/B 46%, 32% 및 25%로 이루어진 콘크리트 시험체에 대하여 $20{\sim}700^{\circ}C$의 다양한 온도하에서 실시하였다. 시험 결과 콘크리트 강도가 증가할수록 고온에서의 상대적인 압축강도와 탄성계수는 감소하였으며, 최대하중에서의 축방향 변형은 설계하중 사전재하와 상관성이 높은 것으로 나타났다. 또한 온도상승에 따른 콘크리트의 열팽창 변형은 압축강도 뿐만 아니라 하중 크기의 영향을 받는 것으로 나타났으며, 최종적으로 가열을 받은 고강도콘크리트의 압축강도 및 탄성계수에 대한 모델식을 제안하였다.