• Korean Journal of Materials Research
• /
• v.20 no.8
• /
• pp.412-417
• /
• 2010

Mo thin films were used for the back electrode because of the low resistivity in the Mo/$CuInGaSe_2$ contact in chalcopyrite solar cells. $1\;{\mu}m$ thick Mo thin films were deposited on soda lime glass by varying the Ar pressure with the dc-magnetron sputtering process. The effects of the Ar pressure on the morphology of the Mo back electrode were studied and the relationships between the morphology and electro-optical properties, namely, the resistivity as well as the reflectance of the Mo thin films, were investigated. The resitivity increased from $24\;{\mu}{\Omega}{\cdot}cm$ to $11833\;{\mu}{\Omega}{\cdot}cm$; this was caused by the increased surface defect and low crystallinity as the Ar pressure increased from $3{\times}10^{-3}$ to $3{\times}10^{-2}\;Torr$. The surface morphologies of the Mo thin films changed from somewhat coarse fibrous structures to irregular and fine celled structures with increased surface cracks along the cell boundaries, as the Ar pressure increased from $3{\times}10^{-3}$ to $3{\times}10^{-2}\;Torr$. The changes of reflectances in the visible light range with Ar pressures were mainly attributed to the surface morphological changes of the Mo thin films. The reflectance in the visible light range showed the highest value of 45% at $3{\times}10^{-3}\;Torr$ and decreased to 18.5% at $3{\times}10^{-2}\;Torr$.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.1
• /
• pp.43-47
• /
• 2022

In this study, we demonstrated an eco-friendly thin-metallic-film-based heater which can be operated in water. Based on the materials stability, Mo was selected as the heating element to secure long-term stability. Using a magnetron sputtering, 40 nm-thick Mo layers were deposited onto a glass substrate, followed by the deposition of 60-nm-thick ZnO layer to prevent oxidation during the heater fabrication process. Then, PVB (Polyvinyl Butyral) was applied on top of ZnO layer and an additional glass substrate was placed, which were heated at 150℃ for 2 hr. The PVB was cured with strong adhesion by the processing condition. We operated the Glass/Mo/ZnO/Glass heater in water, and it was shown that the water temperature reached 50℃ within 2 minutes, with a minimal resistance change of the heater. Finally, the heaters exhibit a semi-transparency, and this aesthetic advantage is expected to contribute to the added value of the heater.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.60.2-60.2
• /
• 2011

본 연구에서는 Indium-free 및 gallium-free 기반의 산화물 TFT를 제작하기 위해 n-type $TiO_2$ 반도체 기반의 thin film transistor ($Mo/TiO_{2-x}/SiO_2/p+\;+Si$)를 oxygen deficient black $TiO_{2-x}$ 타겟을 이용하여 DC magnetron sputtering 공법으로 제작하고 그 특성을 분석하였다. DC magnetron sputtering 공법으로 성막된 $TiO_{2-x}$ semiconductor의 전기적, 광학적, 화학적 결합 에너지 및 구조적 특성 분석을 위해 semiconductor parameter analyzer (Aglient 4156-C), UV/Vis spectrometer, X-ray Photoelectron Spectroscopy, Transmission Electron Microscopy를 각각 이용하여 분석하였으며 이를 RTA 전/후 특성 비교를 통하여 관찰하였다. $TiO_{2-x}$ TFT의 소자 특성은 RTA 열처리 전/후 전형적인 insulator 특성에서 semiconductor 특성으로 변화되는 것을 관찰할 수 있었으며, 최적화된 열처리 공정에서 filed effect mobility 0.69 $cm^2$/Vs, on to off current ratio $2.04{\times}10^7$, sub-threshold swing 2.45 V/decade와 Vth 10.45 V를 확보할 수 있었다. 또한 RTA 열처리 후 밴드갭이 3.25에서 3.41로 확장되는 특성을 나타내었다. 특히 RTA 열처리 후 stoichiometric $TiO_2$ 상태와는 다른 $Ti^{2+}$, $Ti^{3+}$, $Ti^{4+}$ 등의 다양한 oxidation states가 관찰되었으며 이러한 oxidation states를 $TiO_{2-x}$ 박막에서의 oxygen deficient 상태와 연관시킴으로써 oxygen vacancy의 n-type dopant로의 거동을 확인하였다. $TiO_2$ 채널 기반의 TFT 특성을 통하여서 indium free 또는 gallium free 산화물 채널로써의 가능성을 확인하였다.

• Tribology and Lubricants
• /
• v.26 no.6
• /
• pp.317-321
• /
• 2010

Thin films of tin sulphide (SnS) have been formed by a novel 2-stage process where-in D.C. magnetron sputtering was used to deposit to thin films of tin (Sn) and the layers then sulphidised using 5% hydrogen sulphide ($H_2S$) gas in Argon. Although it was not found possible to deposit high quality thin films of tin directly onto glass substrates, excellent layers of tin were produced by using molybdenum (Mo) coated glass as the substrate material. The chemical and physical properties of the SnS layers formed were determined using scanning electron microscopy, energy dispersive x-ray analysis, x-ray diffraction studies and using reflectance versus wavelength measurements and these related to the conditions of synthesis. The data shows that it should be possible to produce conventional "substrate structure" devices based on the use of this technology.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.127-127
• /
• 2011

We investigate the transparent TFTs using a transparent ZnSnO3 (ZTO)/Ag/ZTO multilayer electrode as S/D electrodes with low resistivity of $3.24{\times}10^{-5}$ ohm-cm, and high transparency of 86.29% in ZTO based TFTs. The Transparent TFTs (TTFTs) are prepared on glass substrate coated 100 nm of ITO thin film. On atomic layer deposited $Al_2\;O_3$, 50 nm ZTO layer is deposited by RF magnetron sputtering through a shadow mask for channel layer using ZTO target with 1 : 1 molar ratio of ZnO : $SnO_2$. The power of 100W, the working pressure of 2mTorr, and the gas flow of Ar 20 sccm during the ZTO deposition. After channel layer deposition, a ZTO (35 nm)/Ag (12 nm)/ZTO(35 nm) multilayer is deposited by DC/RF magnetron sputtering to form transparent S/D electrodes which are patterned through the shadow mask. Devices are annealed in air at 300$^{\circ}C$ for 30 min following ZTO deposition. Using UV/Visible spectrometer, the optical transmittances of the TTFT using ZTO/Ag/ ZTO multilayer electrodes are compared with TFT using Mo electrode. The structural properties of ZTO based TTFT with ZTO/Ag/ZTO multilayer electrodes are analyzed by high resolution transmission electron microscopy (HREM) and X-ray photoelectron spectroscopy (XPS). The transfer and output characterization of ZTO TTFTs are examined by a customized probe station with HP4145B system in are.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.633-638
• /
• 1995

Two types of $Ta_2O_{5}$, films, prepared by thermal oxidation and PECVD, on P-type(100) Si wafers were studied to examine the relationship between electrical properties and stresses of the films. For the thermally oxidized films, Ta films were depositied on the Si wafers by dc magnetron sputtering followed by thermal oxidation as functions of oxidation temperature and time. The PECVD films were deposited on the Si wafers as a fuction of RF power density. The relationship between the electrical properties and film stresses were studied. In the case of thermally oxidized $Ta_2O_{5}$ film, the electrical properties and film stress were not found to be dependent on each other, while PECVD $Ta_2O_{5}$ films showed that the electrical properties were depended on the film stress.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.1
• /
• pp.18-22
• /
• 2023

We have investigated the effect of the concentration of oxygen vacancies on the characteristics of Mo-doped ZnO (MZO) thin films for the TCO (transparent conducting oxide). For this purpose, MZO thin films were deposited by RF magnetron sputtering at different substrate temperature from room temperature to 300℃. The electrical resistivity of the MZO films decreases with increasing substrate temperature up to 100℃ and then gradually increases at higher temperatures. To investigate the influences of the ambient gases, the flow rate of oxygen and hydrogen in argon was varied from 0.1 sccm to 0.5 sccm. The MZO thin films were preferentially oriented to the (002) direction, regardless of the ambient gases used. The electrical resistivity of the MZO thin films increased with increasing O₂ flow rates, whereas the electrical resistivity decreased sharply under an Ar+H₂ atmosphere and was nearly the same, regardless of the H₂ flow rate used. As the oxygen vacancy concentration increases, the resistivity intended to decrease. In conclusion, Oxygen vacancy affects the MZO thin film's electrical characteristics. All the films showed an average transmittance of over 80% in the visible range.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.197-197
• /
• 2016

Commercially pure titanium (CP Ti) and Ti-6Al-4V alloys have been widely used for biomedical applications. However, the use of the Ti-6Al-4V alloy in biomaterial is then a subject of controversy because aluminum ions and vanadium oxide have potential detrimental influence on the human body due to vanadium and aluminum. Hence, recent works showed that the synthesis of new Ti-based alloys for implant application involves more biocompatible metallic alloying element, such as, Nb, Hf, Zr and Mo. In particular, Nb and Hf are one of the most effective Ti ${\beta}-stabilizer$ and reducing the elastic modulus. Plasma electrolyte oxidation (PEO) is known as excellent method in the biocompatibility of biomaterial due to quickly coating time and controlled coating condition. The anodized oxide layer and diameter modulation of Ti alloys can be obtained function of improvement of cell adhesion. Manganese(Mn) plays very important roles in essential for normal growth and metabolism of skeletal tissue in vertebrates and can be detected as minor constituents in teeth and bone. Radio frequency(RF) magnetron sputtering in the various PVD methods has high deposition rates, high-purity films, extremely high adhesion of films, and excellent uniform layers for depositing a wide range of materials, including metals, alloys and ceramics like a hydroxyapatite. The aim of this study is to research the Mn coatings on the micro-pore formed Ti-29Nb-xHf alloys by RF-magnetron sputtering for dental applications. Ti-29Nb-xHf (x= 0, 3, 7 and 15wt%, mass fraction) alloys were prepared Ti-29Nb-xHf alloys of containing Hf up from 0 wt% to 15 wt% were melted by using a vacuum furnace. Ti-29Nb-xHf alloys were homogenized for 2 hr at $1050^{\circ}C$. Each alloy was anodized in solution containing typically 0.15 M calcium acetate monohydrate + 0.02 M calcium glycerophosphate at room temperature. A direct current power source was used for the process of anodization. Anodized alloys was prepared using 270V~300V anodization voltage at room. Mn coatings was produced by RF-magnetron sputtering system. RF power of 100W was applied to the target for 1h at room temperature. The microstructure, phase and composition of Mn coated oxide surface of Ti-29Nb-xHf alloys were examined by FE-SEM, EDS, and XRD.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.237-237
• /
• 2010

에너지소비와 엔진 부품의 마모문제를 해결하기 위해, soft-phase를 doping한 hard상의 coating에 대한 실험이 최근 중요한 연구 테마로서 진행 중이다. 특히 MoN-Cu coating은 미국 Argon 연구소의 Erdemer박사 등에 의해, 고온 및 상온 윤활성이 우수한 코팅층으로 보고된 이후 많은 연구가 진행되고 있다. 그러나 기존 연구는 Mo와 Cu의 원소타겟을 이용한 연구가 주력이 되었다. 높은 경도와 저온 고온에서의 낮은 나노 혼합물 코팅 종류는 일반적으로 Mo와 Cu와 같은 원소 합금을 이용한 다수 타겟을 이용한 공정에 의해 진행되어왔다. 이러한 복수의 타겟에 의해 증착 동안에는, 정확한 조성, 큰 크기의 시편들의 균일 증착을 조절하기가 쉽지 않다. 또한, 코팅층에 3번째 성분을 추가하기가 어렵다는 문제점이 있다. 본 연구에서는, 최상의 마찰계수와 표면경도를 보이는 MoN-Cu층을 형성시키기 위하여 합금으로 단일 타겟을 제조하였다. 이를 위한 최적 조성을 결정하기 위하여 Mo, Cu 단일 타겟을 이용한 Unbalanced Magnetron sputtering 법으로 다양한 Cu 함량의 MoN+Cu 합금을 제조하였으며, 이에 대한 경도 및 마찰계수 측정을 통해 최적의 Cu 함량을 결정하였다. 이러한 최적 조성의 Cu 타겟제조를 기계적 합금화와 Spark plasma sintering 기술을 이용하여 제작하였으며, 복수의 합금 타겟과 단일 합금 타겟으로 제조된 코팅층의 물성 비교를 통해 합금 타겟의 우수성 여부를 확인하고자 하였다. 증착된 두 조건의 물성을 비교 단일 타겟은 두가지 타겟으로 증착한 것보다 비슷한 조성에서 경도가 높았으며 경도가 비슷한 조성에서는 마찰계수가 낮았다. 또 입자는 10 at.% Cu 조성에 대해 단일타겟이 50nm 결정립을 갖는 반해 단일타겟은 측정이 불가능할 정도의 미세한 결정립을 가졌다. Erdemir의 연구 결과에 의하면, Cu 함량이 증가함에 따라 columnar 형태의 코팅층구조가 나노 구조로 변한다고 하였는데, 본 연구에서 복수의 원소 타겟에서는 확인이 안되었으며, 단일 합금 타겟에서 완벽한 featurless 형태의 코팅층 구조와 우수한 조도의 박막층을 얻을 수 있었다. 이렇게 제조된 다양한 코팅층에 대한 마찰계수 측정이 진행중이다.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.6
• /
• pp.368-375
• /
• 1995

Thermal CVD method is in general used for the fabrication of TiC/$Al_2O_3$-coated carbide tools. The growth of TiC layer and the coating morphology depended on the chemical composition of the hard metal substrate on which the tool properties were strongly influenced. TiC-coated layer was grown by the diffusion of carbon from the substrate, whereas the growth of $Al_2O_3$ layer was unrelated to the composition of substrate. In the nitride hard coatings of Zr, Nb and Mo metals deposited on high speed steel substrate by magnetron sputtering, the reactivity of the metal elements was decreased with increasing group number in one period of the periodic system. The hard material films exhibited the highest adhesion with the chemical composition of stoichiometry or substoichiometry. The critical load as a measure of adhesion was evaluated using scratch tester. The CVD tools indicated the values of 80 and 40N in the coated layers with proper bonding to the substrate and with $\eta$ phase of 1$\mu\textrm{m}$ in the interface respectively, but the nitride films prepared by sputtering of PVD showed only the values between 10 and 20N.