• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.175-180
• /
• 2011

In this study, the $TiO_{2}/V_{2}O_{5}$ hybrid semiconductors were prepared by mixing $TiO_{2}$ and $V_{2}O_{5}$, and a subsequent smash process to reduce the recombination of electron and improve the efficiency of solar cells. Dye-sensitized solar cells were constructed using the resultant hybrid semiconductor, and their electrochemical properties were also investigated. The photocurrent-voltage curve obtained with the cells indicated a significant increase in the efficiency from 2.9 to 5.7% by the factor of 2 compared to the result obtained only with $TiO_{2}$. It is believed that the introduction of $V_{2}O_{5}$ effectively transport electrons in the $TiO_{2}$ conduction band to FTO glass and suppress recombination with the dye and/or the electrolyte, thus yielding an efficient performance of the dye sensitized solar cell. The impedance values also indicated a decrease of resistance in the interface of $TiO_{2}$/dye/electrolyte supporting the constructive contributions of the smashed $TiO_{2}/V_{2}O_{5}$ hybrid semiconductors for the efficiency.

• Journal of the Korea Concrete Institute
• /
• v.15 no.4
• /
• pp.549-556
• /
• 2003

Various researches on the application of polymer dispersions to the cement mortar and concrete have been practised in many countries like America, Japan and Germany and so on because of high performance and good modification effect of these. In this study, SBR, Polymer dispersion that widely used in situ is employed that the self-flowability may be induced in the cemen mortar. In order to comprehend and investigate the modification of cement mortar with self-flowability by SBR and properties and fracture mode of adhesive strength in tension of that, experimental parameter was set as SBR solid-Cement ratio(S/C) and Cement:Fine aggregate(C:F) and the experiments such as Unit weight, Flow, Consistency change, Crack resistance and Segregation that inform on the general properties have been done. In addition of that, Adhesion in tension is measured with a view to comprehending the properties and fracture mode in tensile load. Consistency change of cement mortar modified by SBR did grow better as the ratio of SBR solid-Cement increased and was much superior to that of resin based flooring such as polyurethane and epoxy which recorded the loss of consistency in 90min. after mixing. Adhesive strength in tension increased with continuity in the curing age and showed the maximum in case of C:F=1:1 and S/C=20%. As the increase of curing age, the fracture mainly happened in the concrete substrate and the interface between the specimen and concrete substrate.

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.421-431
• /
• 2007

The main purpose of this study is to develop a sprayed FRP repair and strengthening method, which is a new technique for strengthening the existing concrete structures by mixing one of the carbon or glass chopped fibers and one of the epoxy or vinyl ester resins with high-speed compressed air in open air and randomly spraying the mixture onto the concrete surface. At present, the sprayed FRP repair and strengthening method using the epoxy resin has not been fully discussed. In order to investigate the material property of the sprayed FRP, this study carried out tensile tests of the material specimens, which were changed with the combinations of various variables including the length of chopped fiber and the mixture ratio of chopped fiber and resin. These variables were set to have the equal material strength, compared with that of one layer of the FRP sheet. As a result, the optimal length of glass and carbon chopped fibers was fumed out to be 38 mm, and the optimal mixture ratio between chopped fiber and resin was also turned out to be 1 : 2 from each variable. And also, the thickness of the sprayed FRP to have the equal strength to one layer of the FRP sheet was finally calculated. In is study, a series of experiments were carried out to evaluate the strengthening effects of flexural beams, shear beams and damaged beams strengthened with the sprayed FRP method, respectively. The results revealed that the strengthening effects of the flexural and shear specimens were reasonably similar to those of the FRP sheet, and the developed Sprayed FRP technique is able to be used as a strengthening scheme of existing RC building.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.1
• /
• pp.81-88
• /
• 2005

The fly ash has been widely used in the latest to complement the performance and economical efficiency of the concrete which uses only a normal portland cement, the pulp ash gained through the incineration of paper sludge is possible to be used as the material of concrete because it contains the properties similar to the previous fly ash in ingredients and physical characteristics. Therefore, this research has tested physical characteristics by replacing 20% of fly ash used with the paper ash to solve the problem which lowers the early strength caused when the fly ash was used. As a result, it showed that the fluidity becomes lower and the compressive strength becomes increased by using paper ash. In addition, after mixing the paper ash with the fly ash, it showed that time and heating amount of the 2nd peak of the minor heat of hydration affecting the revelation of strength was equivalent to the combination for normal portland cement, and also indicated that the compressive strength for 3 days is superior to the combination of the fly ash. Therefore, if the paper ash having a regular fineness is used, it was effective in improving the early strength of concrete used the fly ash.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.1
• /
• pp.21-27
• /
• 2016

Vanadium redox flow batteries (VRFBs) using the electrolytes containing various vanadium ions in sulfuric acid as supporting solution are one of the energy storage devices in alternatively charging and discharging operation modes. The positive electrolyte contains $V^{5+}/V^{4+}$ and the negative electrolyte $V^{2+}/V^{3+}$ depending on the operation mode. To prevent the mixing of two solutions, proton exchange membranes are mainly used in VRFBs. Nafion 117 could be the most promising candidate due to the strong oxidative property of $V^{5+}$ ion, but causes high crossover of electroactive species to result in a decrease in coulombic efficiency. In this study, the composite membranes using Nafion ionomer and porous polyethylene substrate were prepared to keep good chemical stability and to decrease the cost of membranes, and were compared to the properties and performance of the commercially available electrolyte membrane, Nafion 117. As a result, the water uptake and ionic conductivity of the composite membranes increased as the thickness of the composite membranes increased, but those of Nafion 117 slightly decreased. The permeability of vanadium ions for the composite membranes significantly decreased compared to that for Nafion 117. In a single cell test for the composite membranes, the voltage efficiency decreased and the coulombic efficiency increased, finally resulting in the similar energy efficiency. In conclusion, the less cost of the composite membranes by decreasing 6.4 wt.% of the amount of perfluorinated sulfonic acid polymer due to the introduction of porous substrate and lower vanadium ion permeability to decrease self-discharge were achieved than Nafion 117.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.12
• /
• pp.4205-4209
• /
• 2011

The $Li_2Mn_{0.5}Fe_{0.5}SiO_4$ silicate was prepared by blending of $Li_2MnSiO_4$ and $Li_2FeSiO_4$ precursors with same molar ratio. The one of the silicates of $Li_2FeSiO_4$ is known as high capacitive up to ~330 mAh/g due to 2 mole electron exchange, and the other of $Li_2FeSiO_4$ has identical structure with $Li_2MnSiO_4$ and shows stable cycle with less capacity of ~170 mAh/g. The major drawback of silicate family is low electronic conductivity (3 orders of magnitude lower than $LiFePO_4$). To overcome this disadvantage, carbon composite of the silicate compound was prepared by sucrose mixing with silicate precursors and heat-treated in reducing atmosphere. The crystal structure and physical morphology of $Li_2Mn_{0.5}Fe_{0.5}SiO_4$ was investigated by X-ray diffraction, scanning electron microscopy, and high resolution transmission electron microscopy. The $Li_2Mn_{0.5}Fe_{0.5}SiO_4$/C nanocomposite has a maximum discharge capacity of 200 mAh/g, and 63% of its discharge capacity is retained after the tenth cycles. We have realized that more than 1 mole of electrons are exchanged in $Li_2Mn_{0.5}Fe_{0.5}SiO_4$. We have observed that $Li_2Mn_{0.5}Fe_{0.5}SiO_4$ is unstable structure upon first delithiation with structural collapse. High temperature cell performance result shows high capacity of discharge capacity (244 mAh/g) but it had poor capacity retention (50%) due to the accelerated structural degradation and related reaction.

• Elastomers and Composites
• /
• v.47 no.1
• /
• pp.2-8
• /
• 2012

In this study, in order to develop renewable bio-based nanocomposites, multi-functional nanocomposites from soybean resins (AESO, MAESO) and nanoclay were prepared. Photoelectrodes for environmental friendly dye-sensitized solar cell using soybean resin were also prepared. Organo-modified nanoclay was directly dispersed in functionalized soybean resins after mixing with styrene as a comonomer and radical initiator was used to copolymerize the nanocomposites. The observed morphology was a mixture of intercalated/exfoliated structure and the physical properties were improved by adding nanoclay. A nanocomposite using MAESO, which added COOH functional group to the soybean resin, showed better dispersibility than AESO composites. Ultrasonic treatment of the nanocomposites also improved the physical properties. Nanoporous $TiO_2$ photoelectrode was also prepared using soybean resins as a binder, after acid-treatment of $TiO_2$ surface using nitric acid. Dye-sensitized solar cells were prepared after adsorbing dye molecules on it. The $TiO_2$ photoelectrode prepared using soybean binder had high current density because of increased surface area by improved dispersibility. The photoelectrochemical properties and conversion efficiency of the solar cell were significantly improved using the soybean binder.

• Journal of the Korea Concrete Institute
• /
• v.27 no.6
• /
• pp.677-685
• /
• 2015

In a will to subdue the brittleness as well as the low tensile and flexural strengths of ordinary concrete, researches are being actively watched worldwide on steel fiber-reinforced Ultra High Performance Concrete (UHPC) obtained by admixing steel fibers in ultra high strength concrete. For the purpose of maximizing advantage of UHPC, this study removes the upper flange of the steel girder to apply an inverted T-shape girder for the formation of the composite beam. This paper intends to evaluate the behavior of the shear connectors and the flexural characteristics of the composite beam made of the inverted T-shape girder and UHPC slab using 16 specimens considering the compressive strength of concrete, the mixing ratio of steel fiber, the spacing of shear connectors and the thickness of the slab as variables. In view of the test results, it seemed that the appropriate stud spacing should range between 100 mm and 2 or 4 times the thickness of the slab. Moreover, the relative displacement observed in the specimens showed that ductile behavior was secured to a certain extent with reference to the criteria for ductile behavior suggested in Eurocode-4. The specimens with large stud spacing exhibited larger values than given by the design formula and revealed that the shear connectors developed larger ultimate strength than predicted owing to the action of UHPC and steel after non-composite behavior. Besides, the specimens with narrow stud spacing failed suddenly through compression at the upper chord of UHPC before reaching the full capacity of the shear connectors.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.8
• /
• pp.1156-1164
• /
• 2010

Structured lipids (SLs) were synthesized by enzymatic interesterification with evening primrose oil (EPO) and rice bran oil (RBO) in a batch-type reactor. The interesterification was performed using a water shaker for 24 hr at $55^{\circ}C$. Mixing speed was set at 200 rpm and Lipozyme RM IM (immobilized lipase from Rhizomucor miehei, 10% by weight of total substrates) was used as a biocatalyst. Rice bran oil and evening primrose oil were interesterified with various molar ratios (RBO : EPO, 1:3, 1:4, and 1:5 mol/mol). Reversed-phase high performance liquid chromatography connected with evaporative light-scattering detector was performed to separate the triacylglycerol (TAG) species of SLs. In the fatty acid analysis, $\gamma$-linolenic acid (7.9 mol%), linoleic acid (67.3 mol%) and oleic acid (13.2 mol%) were the most abundant fatty acids in the SLs. During 24 hr reaction, most of the reaction occurred within 3 hr. TAG compositions, tocopherols and phytosterols were also analyzed. In the TAG species analysis, LLL (ECN=42, L=linoleic acid) dramatically decreased when the reaction time increased.

• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.12
• /
• pp.1719-1724
• /
• 2016

The objective of this study was to determine the effects of physically effective neutral detergent fiber (peNDF) content in total mixed ration (TMR) on dry matter intake, digestibility, and chewing activity in fattening Hanwoo (Bos taurus coreanae) heifers. The experiment was designed as a replicated $3{\times}3$ Latin square using 12 heifers. Fattening heifers were offered one of three diets [high (T1), medium (T2), and low (T3) peNDF] obtained by different mixing times (3, 10, and 25 min) for the same TMR feed. The peNDF content of TMR was determined by multiplying the proportion of dry matter retained by a 1.18 mm-screen in a Penn State Particle Separator by the dietary NDF content. The $peNDF_{1.18}$ content was 30.36%, 29.20%, and 27.50% for the T1, T2, and T3 diets, respectively (p<0.05). Dry matter intake was not affected by peNDF content in TMR. Total weight gain in T1 group was significantly higher (p<0.05) than in T2 and T3 groups. However, weight gain did not differ between T2 and T3 groups. The feed conversion ratio decreased with an increase in the peNDF content (T1: 12.18, T2: 14.17, and T3: 14.01 g/g). An increase in the peNDF content of TMR was associated with a linear increase in the digestibility of dry matter, crude protein, crude fiber, neutral detergent fiber, and acid detergent fiber (p<0.05). Also, an increase in peNDF content of the TMR resulted in a linear increase in the number of chews in eating and ruminating (p<0.05), and consequently in the number of total chews (p<0.05). These results indicate that peNDF content affects digestibility and chewing activity. Consequently, the peNDF content of TMR should be considered for improving feed efficiency, digestibility, body weight gain, and performance in fattening heifers.