• 센서학회지
• /
• 제7권2호
• /
• pp.103-110
• /
• 1998

강유전체 박막과 마이크로 가공기술을 이용하여 초전형 적외선 센서를 제작하였다. 초전형 적외선 센서는 $Pb_{l-x}La_{x}Ti_{1-x/4}O_{3}$ (x=0.05) (PLT) 강유전체 박막 커패시터를 RF 마그네트론 스퍼터링 방식으로 백감 전극이 증착된 MgO 기판상에 결정 성장시킨 구조를 갖고 있다. 스퍼터링된 PLT 박막은 높은 c-축 결정 구조를 가지므로 센서로 사용하기 위한 분극 처리 과정이 필요 없다. 이는 적외선 이미지 센서를 구현함에 있어서 수율 향상에 필수적인 요소이다. 또한 마이크로 가공 기술을 사용하여 센서의 열용량을 극소화함으로서 센서의 효율을 최대화하였다. 제작된 센서의 상부에 폴리이미드를 코팅하고 MgO 기판을 선택적으로 식각하여 코팅된 폴리이미드와 MgO가 강유전체 박막 커패시터를 지지하고 있는 구조를 구현하였다. 이렇게 제작된 센서의 감도는 상온에서 $8.5{\times}10^{8}cm{\cdot}\sqrt{Hz}/W$로 측정되었으며 이는 마이크로 가공 기술을 사용하지 않은 경우보다 약 100 배의 감도 향상을 가져왔다. 2차원 배열 구조를 갖는 센서를 가지고 인체의 유 무 뿐만 아니라 위치까지 감별할 수 있는 센싱 시스템을 구현하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.143-143
• /
• 2009

In this paper, MgO thin films were deposited on Si(100) single crystal substrates by RF magnetron sputtering. The effects of RF power, chamber atmosphere, and substrate temperature on the characteristics of MgO thin films were already studied. Thus, we focused on the working pressure. The structural properties of the films changed dramatically with deposition conditions. Structural analyses carried out by X-ray diffraction (XRD). MgO films were obtained at the deposition conditions as follows:

• 반도체디스플레이기술학회지
• /
• 제5권1호
• /
• pp.51-55
• /
• 2006

MgO thin films were prepared through electron-beam deposition onto ITO-coated glass substrates in order to measure electrical, dielectric, and microstructural properties. Design of experiments was performed in this study with the aim to understanding of the effects of processing variables, e.g., substrate temperature and filament current of an e-beam evaporator statistically. Leakage currents, relative dielectric constants, and diffraction intensities of MgO thin films were analyzed statistically, following the analysis procedure provided in the design of experiments. The leakage current level of MgO thin films has been found to be statistically significant at the level of $\alpha=0.1$.

• 한국표면공학회지
• /
• 제37권3호
• /
• pp.169-174
• /
• 2004

MgO thin films were reactively deposited using an internal inductively coupled plasma assisted sputtering method varying reactive gas ratio to get stoichiometric film composition, and bipolar dc substrate bias to suppress micro arcs. The minimum frequency required for arc suppression was about 10KHz depending on ICP power. Their crystallinity was analyzed using X-ray diffraction and surface morphology using AFM. The surface was very smooth with rms roughness less than 0.42nm. The preferred orientation of the films were changing from (200) to bulk-like characteristics as Ar: $O_2$ratio was controlled to 10 : 2. Optical emission spectroscopy revealed that there were two distinct discharge modes: a blue one and a green one, where enhanced emission from Ar and Mg were observed. This cannot simply be understood by metallic or oxide mode of reactive sputtering due to ICP coupled to magnetron discharge.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.379-382
• /
• 1999

In this paper, we investigated the characteristics of MgO thin film prepared by unbalanced magnetron sputtering(UBMS) in surface discharge type AC PDP The minimum discharge voltage is obtained for the sample of substrate bias voltage-10V. Moreover the anti-sputtering characteristics of MgO thin film by UBMS is improved about 40% than one of balanced magnetron sputtering(BMS)

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.26-29
• /
• 1999

Superconducting $YBa_{2}$$Cu_{3}$ $O_{7-x}$(YBCO) thin films were deposited on MgO(100) substrates using a hollow cathode discharge sputtering system. Influence of the sputtering conditions such as substrate temperature and discharge sputtering gas pressure on electrical and structural properties were investigated. It was found that YBCO thin films with zero resistance temperature higher than 85 K were obtained to the pressure 200 mToorr(Ar/O2=0.9), substrate temperature of $760^{\circ}C$, and target-substrate distance of 10 mm during film deposition. Homogeneous large area YBCO films with 2 inch diameter were also sucessfully fabricated by this method.

• 한국결정성장학회지
• /
• 제1권1호
• /
• pp.1-4
• /
• 1991

The applicability of $LiNbO_{3}$ as a substrate for fabrication of Ti-indiffused waveguide electro-optic devices is limited. Ti diffuses comparatively in congruently melting $LiNbO_{3}$; the Curie temperature of this material is too low to permit diffusion temperatures much above $1100^{\circ}C$ without the necessity of re-poling the crystal. Both of hese difficulties could be eliminated by incorporating certain dopants in $LiNbO_{3}$. Crystals of $LiNbO_{3}$ doped with Ti and Mg were grown and evaluated. The electroptic coefficients and birefringence of $LiNbO_{3}$ doped crystals were measured at ${\lambda}=.6328$ and $1.32\;$\mu{m}$. Curie temperatures were measured. The Curie temperature of both undoped and Ti-doped $LiNbO_{3}$ was $1130^{\circ}C$; that for Mg-doped $LiNbO_{3}$ was $30^{\circ}$ higher. From these data, a composition for the crystals was estimated. Thermogravimetric data confirmed this estimate and showed that the composition of Mg : $LiNbO_{3}$ was $49.3{\pm}0.2mole%\;Li_{2}O$ ; the composition of the undoped and Ti : $LiNbO_{3}$ samples was $48.6{\pm}0.2mole%$. Diffusion of Ti into both Mg-doped and Ti-doped $LiNbO_{3}$ crystals was studied as a function of $Li/NbO_{3}$ ratio and temperature.

• 한국재료학회지
• /
• 제4권8호
• /
• pp.870-876
• /
• 1994

$Y_{1}Ba_{2}Cu_{3}O_{7-\delta}$계에서 211상의 성장거동을 관찰하기 위하여 123시편을 $1100^{\circ}C$에서 유지시간을 변화시켜 MgO다결정 기판과 MgO 단결정 기판위에 놓고 소결시킨 후 공냉하였다. 211입자는 유지 시간이 증가함에 따라 성장하였으며MgO단결정 기판보다 MgO다결정 기판을 사용했을때 더 큰 성장을 보였다. CuO양을 변화시키면서 만든 $Y_{2}Ba_{1+X}Cu_{3}O_{5+\delta}$ 시편에서 211입자는 CuO양이 증가함에 따라 조대해졌으며 0.6mol CuO가 더 첨가된 시편에서 가장 큰 211입자가 관찰되었다. $Y_{2}Ba_{1+X}Cu_{3}O_{5+\delta}$시편에서 211입자는 아주 미세하고 균일하게 분포되었다. $SnO_{2}$첨가로 인한 211입자의 성장억제 효과는 ($BaCuO_{2}$+ CuO)액상에서보다 CuO액상에서 더 크게 나타났다.

• Progress in Superconductivity
• /
• 제2권2호
• /
• pp.71-75
• /
• 2001

The effect of annealing step-edges of LaAlO$_3$ and MgO single crystal substrates on YBa$_2$Cu$_3$O$_{7}$ junction has been studied. The step-edge was fabricated by argon ion milling and was annealed at 105$0^{\circ}C$ in 1 attn oxygen pressure. We compared AFM image near step-edge of the substrates between before and after annealing process. And YBa$_2$Cu$_3$O$_{7}$ thin film was deposited on the step-edge by a standard pulsed laser deposition. The step-edge junctions were characterized by current-voltage curves at 77 K. The annealing of step-edges of MgO substrate improved the current-voltage characteristic of Josephson junction: double steps in the current-voltage characteristic disappeared. However the annealing for LaAlO$_3$ did not improve the junction property.rty.

• Journal of Magnetics
• /
• 제13권4호
• /
• pp.163-166
• /
• 2008

Multiferroic $CoCr_2O_4$ film was deposited on MgO and $MgAl_2O_4$ substrates by the rf-sputtering process. The films were prepared at an RF-magnetron sputtering power of 50 W and a pressure of 10 mtorr (20 sccm in Ar), and at substrate temperatures of $550^{\circ}C$. The crystal structure was determined to be a spinel (Fd-3m) structure by means of X-ray diffraction (XRD) with Cu $K{\yen}{\acute{a}}$ radiation. The thickness and morphology of the films were measured by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The magnetic properties were measured using a Superconducting Quantum Interference Device (SQIUD) magnetometer. While the ferrimagnetic transitions were observed at about 93 K, which was determined as the Neel temperature, the magnetic properties all show different behaviors. The differences between the magnetic properties can be explained by the stress effects between $CoCr_2O_4$ and the substrates of MgO and $MgAl_2O_4$.