• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.802-805
• /
• 2003

The ion-induced secondary electron emission coefficient ${\gamma}$ for MgO thin film with $O_{2}$ plasma treatment has been investigated by ${\gamma}$-FIB (focused ion beam) system. The MgO thin film deposited from sintered material with $O_2$ plasma treatment is found to have higher ${\gamma}$ than that without $O_{2}$ plasma treatment. The energy of $Ne^{+}$ ions used has been ranged from 100eV to 200eV throughout this experiment. It is found that the highest secondary electron emission coefficient ${\gamma}$ has been achieved for 10 minutes of $O_{2}$ plasma treatment.

• 한국세라믹학회지
• /
• 제37권6호
• /
• pp.537-544
• /
• 2000

Thin-film humidity sensor which TiO2, ZrO2, or CeO2 was added to MgCr2O4-based materials, respectively, were fabricated on the alumina substrate by using a resistant-heating evaporator. Thin films were approximately 2${\mu}{\textrm}{m}$ in grain size and shwoed porous microstructures. The resistance of the sensor decreased with increasing the relative humidity and the MgCr2O4-TiO2 sensor had the best humidity-sensing characteristics (linearity in relative humidity versus resistance).

• 한국전기전자재료학회논문지
• /
• 제20권8호
• /
• pp.716-719
• /
• 2007

The effects of the evaporation rate of MgO films using an electron beam on the MgO properties and the discharge characteristics of a plasma display panel (PDP) were investigated and analyzed. MgO films were deposited with the various MgO evaporation rates. The MgO properties such as the crystal orientation, the surface roughness, and the film structure were inspected using XRD (X-ray diffraction), AFM (atomic force microscopy). From the experiments and Paschen law, the maximum value of the secondary electron emission coefficient $({\gamma})$ was obtained at the evaporation rate of $5{\AA}/sec$. The XRD results and cathode-luminescence (CL) spectra show the ${\gamma}$ values are correlated with F/F+ centers of the molecular structure of MgO films. The minimum firing voltage and the maximum luminous efficiency were obtained at an evaporation rate of $5{\AA}/sec$. In the MgO film deposited at $5{\AA}/sec$, the (200) orientation and F+ center were most intensive.

• 한국진공학회지
• /
• 제11권3호
• /
• pp.135-140
• /
• 2002

본 논문에서는 p-type (100)Si, (100)MgO 그리고 MgO/si 기판 위에 RF Magnetron sputtering 법으로 $Ba_{0.5}Sr_{0.5}TiO_3$(BST)박막을 증착하였다. BST 박막 증착 후 RTA(Rapid Thermal Annealing)를 이용하여 $600^{\circ}C$에서 산소분위기로 1분간 고온 급속 열처리를 하였다. 증착된 BST박막의 결정화를 조사하기 위해 XRD(X-Ray Diffraction)측정을 한 결과 모든 기판에서 (110) $Ba_{0.5}Sr_{0.5}TiO_3$(의 주피크가 관찰되어졌고, 열처리 후 재결정화에 기인하여 피크 세기가 증가함을 관찰할 수 있었다. Al 전극을 이용한 커패시터 제작 후 측정한 C-V(Capacitance-Voltage) 특성에서 각각의 기판에서 측정된 커패시턴스 값으로 계산된 유전율은 120(bare Si), 305(Mgo/Si) 그리고 310(MgO)이었다. 누설 전류 특성에서는 0.3 MV/cm이내의 인가전계에서 1 $\mu\textrm{A/cm}^2$ 이하의 안정된 값을 보여주었다. 결론적으로 MgO 버퍼층을 이용한 기판이 BST 박막의 증착을 위한 기판으로써 효과적임을 알 수 있었다.

• 대한화학회지
• /
• 제61권2호
• /
• pp.57-64
• /
• 2017

Monoclinic $VO_2(M)$ nanoparticles codoped with 1.5 at. % W and 2.9 at. % Mg were synthesized by the hydrothermal treatment and post-thermal transformation method of $V_2O_5-H_2C_2O_4-H_2O$ with $Na_2WO_4$ and $Mg(NO_3)_2$. The composite thin film of the W/Mg-codoped $VO_2(M)$ with a commercial acrylic block copolymer was also prepared on PET substrate by wet-coating method. The reversible phase transition characteristics of the codoped $VO_2(M)$ nanoparticles and the composite film were investigated from DSC, resistivity and Vis-NIR transmittance measurements compared with the undoped and Wdoped $VO_2(M)$ samples. Mg-codoping into W-doped $VO_2(M)$ nanoparticles synergistically enhanced the transition characteristics by increasing the sharpness of transition while the transition temperature ($T_c$) lowered by W-doping was maintained. The codoped composite film showed the prominently enhanced NIR switching efficiency compared to only W-doped $VO_2(M)$ film with a lowered $T_c$.

• 한국재료학회지
• /
• 제30권10호
• /
• pp.566-572
• /
• 2020

In the recent years, thin film solar cells (TFSCs) have emerged as a viable replacement for crystalline silicon solar cells and offer a variety of choices, particularly in terms of synthesis processes and substrates (rigid or flexible, metal or insulator). Among the thin-film absorber materials, SnS has great potential for the manufacturing of low-cost TFSCs due to its suitable optical and electrical properties, non-toxic nature, and earth abundancy. However, the efficiency of SnS-based solar cells is found to be in the range of 1 ~ 4 % and remains far below those of CdTe-, CIGS-, and CZTSSe-based TFSCs. Aside from the improvement in the physical properties of absorber layer, enormous efforts have been focused on the development of suitable buffer layer for SnS-based solar cells. Herein, we investigate the device performance of SnS-based TFSCs by introducing double buffer layers, in which CdS is applied as first buffer layer and ZnMgO films is employed as second buffer layer. The effect of the composition ratio (Mg/(Mg+Zn)) of RF sputtered ZnMgO films on the device performance is studied. The structural and optical properties of ZnMgO films with various Mg/(Mg+Zn) ratios are also analyzed systemically. The fabricated SnS-based TFSCs with device structure of SLG/Mo/SnS/CdS/ZnMgO/AZO/Al exhibit a highest cell efficiency of 1.84 % along with open-circuit voltage of 0.302 V, short-circuit current density of 13.55 mA cm^-2, and fill factor of 0.45 with an optimum Mg/(Mg + Zn) ratio of 0.02.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.15-17
• /
• 2005

In this study, tunable dielectric materials are important for resonator, variable capacitor, phased array antenna and other devices application. In this paper, Dielectric constant increased and tuning range increased with the increased of $BaSrTiO_3/Li_{2}CO_{3}$ content, which probably can be explained by the substitution of Ba3+, Li1+ on BaTiO3 lattice. The tunability and dielectric loss of the $BaSrTiO_2/Li_{2}CO_{3}$ thick film, sintered at $1150^{\circ}C$, were about 43 % and 0.234 at 10$\sim$15 MHz, respectively. In case of BaSrTi/MgO, Dielectric constant decreased and tenability increased with the added of $BaSrTiO_3/MgO$. The ferroelectrics properties were distinct when adding Li to BST ceramic thick film, and paraelectrics pattern was distinct when adding Mg.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.19-20
• /
• 2007

At first the $Ba_{0.5}Sr_{0.5}TiO_3$-MgO powder with $B_2O_3-Li_2CO_3$ were made by the Sol-Gel method. The thick films of BST-MgO with $B_2O_3-Li_2CO_3$ were fabricated on the $Al_2O_3$ substrates coated with Pt by the screen printing method. The structural and dielectric properties of the BST-MgO thick film with $B_2O_3-Li_2CO_3$, addition were investigated. The structure of the BST-MgO with $B_2O_3-Li_2CO_3$ thick films were dense and homogeneous with no pores. The dielectric constant was increased and dielectric loss was decreased with increasing the sintering temperature.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.890-893
• /
• 2006

Effects of the evaporation rate of MgO films using electron beam were investigated on the MgO properties and the discharge characteristics of the plasma display panel (PDP). The evaporation rate was changed from 3 ${\AA}/sec$ to 15 ${\AA}/sec$ at a substrate temperature of $300\;^{\circ}C$. MgO properties such as crystal orientation, surface roughness, contact angle, and film structure were inspected using XPS, AFM, drop shape analysis and SEM. We also studied the relation between MgO properties and PDP discharging characteristics. The minimum firing voltage and maximum efficacy were obtained at evaporation rate of 5 ${\AA}/sec$. In the MgO film deposited at 5 ${\AA}/sec$, (200) orientation was most intensive and surface roughness was minimum.

• 한국전기전자재료학회논문지
• /
• 제33권3호
• /
• pp.214-218
• /
• 2020

In this study, Mg_xZn_1-xO thin films, which can be applied not only to active layers of light-emitting devices (LEDs), such as UV-LEDs, but also to solar cells, high mobility field-effect transistors, and power semiconductor devices, are fabricated using the sol-gel method. ZnO and Mg_0.3Zn_0.7O solution synthesized by the sol-gel method and the thin film were grown by spin coating on a Si (100) substrate and sapphire substrate. The solutions are synthesized by dissolving precursor materials in 2-methoxyethanol (2-ME) solvent, and then monoethanolamine (MEA) was added to the mixed solution as a sol stabilizer. Zinc acetate dihydrate is used as a ZnO precursor, while Mg nitrate hexahydrate and Mg acetate tetrahydrate are used as an MgO precursor. Then, the optical and structural characteristics of the fabricated thin films are compared. The molar concentration of the Zn precursor in the solvent is fixed at 0.3 M, and the amount of the Mg precursor is 30% of Mg²⁺/Zn²⁺. The optical characteristics are measured using an UV-vis spectrophotometer, and the transmittance of each wavelength is measured. Structural characteristics are measured using X-ray diffraction (XRD) and transmission electron microscopy (TEM). Composition analyses are performed using energy dispersive X-ray spectroscopy (EDS). The Mg_0.3Zn_0.7O thin film was well formed at the ratio of the Mg precursor added regardless of the type of Mg precursor, and the c-axis of the thin film was decreased, while the band gap was increased to 3.56 eV.