• 한국분말재료학회지
• /
• 제2권2호
• /
• pp.135-141
• /
• 1995

As the first step of study on fabrication of ceramic powders from phytoliths in rice, especially in rice husks, pulverization method of rice husks and the properties of milled rice husks were investigated. Impact methods, such as ball milling, were not meaningful for pulverizing elastic and thin fabric structure of rice husks. The most effective one was cutting method. In the present work, a rotating knife cutting method was applied to pulverizing rice husks. A 40-mesh screen was inserted under the rotating knives. The most portion of the milled powder was found in -50/+100 mesh section. Morphology of the milled rice husks revealed that the husks larger than 70 mesh were flake-like shape, at -70/+100 mesh section relatively equi-axed shape, at -170/+325 mesh section rod-like shape, and below 325 mesh section dust-like shape. Tap density of raw rice husks was about 0.1 $g/cm^3$, while those of milled rice husks were over $0.4 g/cm^3$. This meant that, for a given volume of reactor, raw material charge can be increased more that 4 times when using milled rice husks than unmilled one. True densities of unmilled and milled rice husks were higher than $1.4 g/cm^3$, and increased with decreasing milled sizes.

• 한국공간구조학회논문집
• /
• 제7권3호
• /
• pp.153-165
• /
• 2007

연성 구조물은 축강성은 강하고 휨 강성이 매우 작은 재료를 주 구조재로 사용하므로 초기강성에 매우 민감한 구조체이다. 막 구조물을 설계하기 위해서는 우선 초기장력 도입으로 인한 구조물의 형상을 정확히 알아야 한다. 이를 위해서 모형을 통한 모델링이나 컴퓨터를 이용한 형상해석이 요구되며, 초기장력의 도입으로 형성되는 막 구조물의 곡면은 일반적으로 등장력 곡면이다. 따라서 연성 구조물의 해석과 설계는 기존의 강성구조물과는 다른 형상해석, 응력-변형해석, 재단도 작성 및 시공해석의 3단계 해석이 요구되어진다. 본 연구는 재단도 작성 프로그램 NASScut를 이용하여 경계면 곡률의 오차를 최소화 할 수 있는 삼각형 Re-mesh 패턴을 제안하고, 재단도를 작성한다.

• International Journal of CAD/CAM
• /
• 제11권1호
• /
• pp.11-17
• /
• 2011

A new method has been developed in this paper for automatic quadrilateral mesh generation for a two-dimensional domain. The method is named 'centering method' because it centers a point at the domain and then divides it into sub-domains using cutting lines from the center point. Each of the cutting lines is selected based on the criterion using the angles between the boundary of the domain and the cutting line. The decomposition of the domain into sub-domains is repeated until every subdomain has four or six nodes. Pre-defined splitters are used to divide six-node domains into quadrilateral elements depending on their configuration and presence on the boundary of the initial domain. Arbitrary domains are meshed as examples to verify the robustness of the new method.

• Tribology and Lubricants
• /
• 제23권4호
• /
• pp.149-155
• /
• 2007

The CAD model of a elliptical gear for wire cutting has been developed. The rolling contact of pitch ellipses whose rotation axes coincide with their focus has been analyzed, and the perimeter of the pitch ellipse has been divided into equal-length segments by the number of teeth. A master tooth profile, which is a composite curve of circular arcs that represents involute, has been introduced. The elliptical gear has been designed by imposing the master tooth on the divided points of the pitch ellipse, and a full fillet has been achieved between neighbour teeth. Thus, the whole profile of an elliptical gear is a composite curve of arcs only, and consequently NC codes for wire cutting can be easily generated. Furthermore, a computer simulation program is developed to verify the mesh of the elliptical gear.

• Journal of Welding and Joining
• /
• 제21권5호
• /
• pp.525-533
• /
• 2003

The dimensional accuracy and global roughness between successive layers of VLM-s, which is a new rapid prototyping process using hotwire cutter and EPS foam, depend significantly on the operating parameters of hotwire cutter. In the present study, the effect of cutting angle on the kerf width and edge shape in hotwire cutting of EPS foam for the case of single-sloped cutting with one cutting angle was investigated. Through single-sloped cutting tests, the modified relationship between kerf width and effective heat input, considering the effect of the cutting angle, and the relationship between the melted area and the cutting angle were obtained. In order to investigate the effect of cutting angles on the thermal field in EPS foam, transient heat transfer analyses using single-sloped volumetric heat flux model and locally-conformed mesh were performed. Through the comparison between experimental and numerical results, it was shown that the proposed analysis model is needed to estimate the three-dimensional temperature distribution of the EPS foam for the case of single-sloped hotwire cutting.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.176-180
• /
• 2002

All types of VLM-s process include the linear heat cutting of EPS foam to generate a layer with 3D shape. The dimensional accuracy and part quality of the cut part are dependent on the thermal characteristics in the EPS foam. The thermal characteristics are determined by operating parameters such as an effective heat input and cutting angle. The objective of this study is to investigate into the influence of cutting angle on the kerfwidth and the melted length of the cut part using the numerical analysis and the experiments in generally sloped cutting with two cutting angles. In order to estimate an accurate temperature field, the transient thermal analysis using moving coordinate system, the fully conformed mesh and the heat flux model with two cutting angles is carried out. From the results of the analysis and the experiments, it has been found that the influence of the rotational angle about x-axis in which the rotational axis is normal with hotwire cutting direction is appreciably negligible in comparison with that of the rotational angle about y-axis.

• 디지털융복합연구
• /
• 제13권4호
• /
• pp.303-310
• /
• 2015

최근 게임 기술은 모의 수술 시뮬레이션이나 사이버 모델하우스 구축 등의 여러 응용 분야에까지 적용되어지고 있다. 이러한 응용 분야에서 꼭 필요하고 중요한 기술 중 하나는 3D 모델을 실시간으로 절단하는 것이다. 실시간 모의 절단 기술은 자동차나 건축물의 실시간 해체 시뮬레이션 구축에 꼭 필요하며, 다양한 융복합 산업 분야에서 응용이 가능하다. 기존의 BSP-Tree를 이용한 절단 기법에서는 무한 평면을 기준으로 3D 모델을 두 부분으로 절단시키기 때문에 일반적인 절단 작업에 유용하게 사용하기 어렵다. 본 논문에서는 이러한 문제점을 해결하기 위해 유한한 영역 내에서 3D 모델을 절단하는 기법을 제안하였다. 구체적으로 절단 경로면을 유한하게 정의할 수 있도록 하였으며, 절단 범위 이내에서만 3D 모델을 분열시키도록 하여, 다양한 산업 분야에서 유용하게 사용할 수 있도록 하였다. 본 연구에서 제안한 부분 절단 기법의 유용성을 보이기 위해 원자로 3D 모델의 해체 작업 과정을 모의 시뮬레이션 하는 과정에 적용해 보았다.

• Journal of Computational Design and Engineering
• /
• 제3권2호
• /
• pp.151-160
• /
• 2016

Cutter-workpiece engagement (CWE) is the instantaneous contact geometry between the cutter and the in-process workpiece during machining. It plays an important role in machining process simulation and directly affects the calculation of the predicted cutting forces and torques. The difficulty and challenge of CWE determination come from the complexity due to the changing geometry of in-process workpiece and the curved tool path of cutter movement, especially for multi-axis milling. This paper presents a new method to determine the CWE for general milling processes. To fulfill the requirement of generality, which means for any cutter type, any in-process workpiece shape, and any tool path even with self-intersections, all the associated geometries are to be modeled as triangle meshes. The involved triangle-to-triangle intersection calculations are carried out by an effective method in order to realize the multiple subtraction Boolean operations between the tool and the workpiece mesh models and to determine the CWE. The presented method has been validated by a series of case studies of increasing machining complexity to demonstrate its applicability to general milling processes.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.142-148
• /
• 2008

This study aims to find the optimal cutting conditions, which are obtained by grinding condition, and the grinding characteristics and condition of constant velocity joint were investigated with respect to wheel velocity, depth of cut, feed speed. Grinding machine has been widely used in manufacturing optical reflects of metal. Such as steel are easy to be machined because of their proper material. As a result I obtained the data of grinding conditions makes good surface roughness and the optimal condition of grinding and get the mesh condition. The purpose of this study is to find the optimum grinding wheel characteristics for cutting constant velocity joint.

• 복식문화연구
• /
• 제28권6호
• /
• pp.738-754
• /
• 2020

As a cultural feature of, the relics of the Royal Tomb of King Muryeong are suitable design content for applying with sophisticated production and delicate molding laser cutting techniques. The purpose of this study is to develop modern bag designs using relics of the Royal Tomb of King Muryeong of Baekje using laser-cutting techniques. First, the historical background and meaning of Baekje's cultural content were explored. Second, the principle of laser-cutting techniques were explored, laser-cutting techniques applied to modern fashion and bag design were examined, and bag design characteristics were analyzed. Third, based on prior research, the criteria for the development of bag design, from which eight bag design were developed that combine modern popularity and functionality utilizing Baekje cultural content and using laser-cutting techniques to apply the textile design developed by researchers in 2013 (modified to match laser-cutting techniques). The research results show that bag were clutch, tote, shoulder, and mini. Gold, silver, brown, beige, and navy colors were arranged, based on black/white contrast. Cow, lambskin, washed snakeskin, mesh, and Saffiano leather were used. For the pattern-applying technique, this study showed that a new digital technique, which is laser-cutting techniques could be combined with contemporary bag designs. Moreover, a bag design was developed that has a modern sense and functionality as well as Korean formativeness, which is significant.