• Journal of the Korean Society for Nondestructive Testing
• /
• v.7 no.2
• /
• pp.35-41
• /
• 1988

The optimum test conditions of measuring the crack height were determined for the two-probe ultrasonic diffraction method. The applicability and the accuracy of the two-probe ultrasonic diffraction method on the inclined artificial cracks and the fatigue cracks were evaluated. It us possible to measure the height of the normal and inclined artificial cracks with the maximum error of ${\pm}\;0.5mm$ with the two-probe ultrasonic diffraction method. It was found, however, that the accuracy of this method in meaasuring the height of the fatigue crack depends on the degree of closure of the crack tip. It was desirable to choose a refraction angle as small as possible, but the angle should not be so small that the distortion of the lateral waveform became appreciable.

• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.162-164
• /
• 2006

This whitepaper is a research about the sensor network technology which enhance the performance of the blood management system. The problem of measuring and monitoring the real time temperature of a every point in a limited environment let us to develop a system which is able to monitor the temperature of a remote area using multi-hop networking technology. This whitepaper propose the error correction technologies, which were used to eliminate problems that might occur during real tests of the system.

• Journal of Mechanical Science and Technology
• /
• v.18 no.5
• /
• pp.789-797
• /
• 2004

The nanoscale sensing and manipulation have become a challenging issue in micro/nano-robotic applications. In particular, a feedback sensor-based manipulation is necessary for realizing an efficient and reliable handling of particles under uncertain environment in a micro/nano scale. This paper presents a piezoresistive MEMS cantilever for nanoscale force measurement in micro robotics. A piezoresistive MEMS cantilever enables sensing of gripping and contact forces in nanonewton resolution by measuring changes in the stress-induced electrical resistances. The calibration of a piezoresistive MEMS cantilever is experimentally carried out. In addition, as part of the work on nanomanipulation with a piezoresistive MEMS cantilever, the analysis on the interaction forces between a tip and a material, and the associated manipulation strategies are investigated. Experiments and simulations show that a piezoresistive MEMS cantilever integrated into a micro robotic system can be effectively used in nanoscale force measurements and a sensor-based manipulation.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.238-246
• /
• 1996

When the important structures or components of agricultural machinery are designed, the full-filed methods of stress analysis can provide enough information in order to obtain lighter weight and prevent failure. The photoelasticity has been applicated to solve many practical engineering problems. The coating method provides full-field information, enabling the engineers to determine the complete distribution of surface strains and directly highlighting severely strained areas, especially for the welded frames of agricultural machinery. A combined method of model and prototype for strain analysis of excavator has been successfully applied to improve design. A measuring and recording system controlled by micro-computer and application software for dynamic event was studied. It can be widely used in structural failure analysis under cyclical loading . Typical application concerned stress field of crack tip and failure analysis of some mechanical structures are introduced are in roduced briefly in this paper.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.141-148
• /
• 2002

Experimental investigation of the interaction between dual spray formed by swirl type injector was conducted. Experimental parameter was fuel temperature, varied in the range from $-20^{\circ}C$ to $120^{\circ}C$. Measuring parameter were vertical distance from injector tip to patternator and gap between injectors. Volumetric distiribution and SMD were measured for the various combination of parameters. The results of present study show that the arithmetic sum of each of spray is not equal to dual spray, but it is equal above specific fuel temperature. As the increases of fuel temperature, SMD decreases and becomes more uniform. As the increases of gap between injectors, fuel volume and SMD at collision area increases, but penetrated fuel decreases.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.746-751
• /
• 2002

This purpose of this study was to design the effect of recovering of a hand amputees by myoelectronic hand. It was designed with 2 degree of freedom in tile laboratory. Myoelectronic hand had only one degree of freedom and one movement until now. Also this myoelectronic hand had multi-joint system. Myoelectronic hand data was obtained by measuring hand and data was applied when it was designed myoelectronic hand. PID controll of myoelectronic hand was used to it. Displacement control was applied the first link of finger. Experiment was accomlkished in Tip grasp, power grasp and Hook grasp modes. Displacement controll was good in low frequency. Velocity control was applied to each mode. This myoelectronic hand with a hand amputees could do some jobs such as grasping materials. Further studies were needed to evaluate the effect of a myoelectronic hand with more precise laboratory equipment.

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.53-55
• /
• 2005

The surface potential variations are measured, according to the enhanced measuring speed and voltage sensitivity, using an active device, such as a field effect transistor $(FET)^{1-3}$. In this study, the surface potential was mapped in the patterned $SiO_2$ medium at room temperature. An improved FET-tip cantilever, which has a source, a drain, and an n- channel, was used in this study. The potential images were analyzed both in the contact mode and the non-contact mode, using only a pre-amplifier system instead of a lock-in the amplifier.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 2002.11a
• /
• pp.36-36
• /
• 2002

To Establish of standard technique of length measurent in 2D plane, we develope AFM system. The XY scanner scans the sample only in XY plane, while the Z scanner scans the specimen only in Z-direction. Cantilever tip is controlled to has constant height relative to speciman surface by feedback of PSPD signal. To acquire high accuracy, Z-axis measuring sensor will be added.(COXI or others). In this paper we design XYZ stage suitable for this AEM system. For XY stage, single module parallel-kinnematic flexure stage is used which has high orthogonality and minimum out-of-plane motion. To obtain best performance optimal design is performed. For XY stage, to be robust about parasitic motion optimal design of maximizing Z and tilt stiffness is performed under the constraint of motion range and stage size. And for Z stage, optimal design of maximizing 1st resonant frequency is performed. Because if resonant frequency is get higher, scan speed is improved. So it makes reduce the error by sensor drift. Resultly XYZ stage each have 1st natural frequency of 115㎐, 201㎐, 2.66㎑ and range 109㎛, 110㎛, 12㎛.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.104-109
• /
• 2011

I present a method of aspheric surface profile measurement using 2nd derivative of local area profile. This method is based on the principle of curvature sensor which measures the local 2nd derivative under test along a line. The profile is then reconstructed from the data on the each point. Unlike subaperture-stiching method and slope detection method, 2nd derivative method has strong points from a geometric point of view in measuring the aspheric surface profile. The second derivative terms of surface profile is an intrinsic property of the test piece, which is independent of its position and tip-tilt motion. The curvature is measured at every local area with high accuracy and high lateral resolution by using White-light scanning interferometry.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.111-118
• /
• 2014

Aluminum lithium alloys are new materials developed for lightweight aircraft parts. However, as compared with conventional aluminum alloys in high-speed machining, problems such as tool wear, machining distortion, and cutting ability arise. This study presents the machining distortion characteristics of an Al-Li alloy wing tip in relation to the cutting heat in high-speed machining. A machining experiment was conducted with high-speed machining equipment for an evaluation of the machining distortion characteristics, with each machining stage temperature change of the workpiece machining surface, and the inside and outside temperature changes of the equipment measured. By measuring the amount of distortion of the workpiece before and after machining, the cutting heat was analyzed with regard to its effect on machining distortion in the product.