• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.10A
• /
• pp.1582-1589
• /
• 2000

A dynamic D-flipflop is proposed aiming at low power and high frequency(GHz) operations. The proposed D-flipflop uses a smaller number of pmos transistors that it operates high speed in same dimensions. Also, it consumes lower power than conventional approaches by a shared nmos with clock input. In order to compare the performance of the proposed D-flipflop, we perform simulation estimating power consumption and maximum operating frequency of each same dimension D-flipflop. A high speed dual-modulus prescaler employing the proposed D-flipflop. A high speed dual-modulus prescaler employing the proposed D-flipflop. A high speed dual-modulus prescaler employing the proposed D-flipflop is evaluated via the same method. The simulation results show that the proposed D-fliplflop has good performance than conventional circuits.

• Journal of Information Processing Systems
• /
• v.18 no.4
• /
• pp.457-469
• /
• 2022

Hydraulic concrete buildings in the northwest of China are often subject to the combined effects of low-temperature frost damage, during drying and wetting cycles, and salt erosion, so the study of concrete deterioration prediction is of major importance. The prediction model of the relative dynamic elastic modulus (RDEM) of four different kinds of modified concrete under the special environment in the northwest of China was established using Grey residual Markov theory. Based on the available test data, modified values of the dynamic elastic modulus were obtained based on the Grey GM(1,1) model and the residual GM(1,1) model, combined with the Markov sign correction, and the dynamic elastic modulus of concrete was predicted. The computational analysis showed that the maximum relative error of the corrected dynamic elastic modulus was significantly reduced, from 1.599% to 0.270% for the BS2 group. The analysis error showed that the model was more adjusted to the concrete mixed with fly ash and mineral powder, and its calculation error was significantly lower than that of the rest of the groups. The analysis of the data for each group proved that the model could predict the loss of dynamic elastic modulus of the deterioration of the concrete effectively, as well as the number of cycles when the concrete reached the damaged state.

• Current Optics and Photonics
• /
• v.7 no.4
• /
• pp.337-344
• /
• 2023

Three-point bending is the main method for measuring the elastic modulus of a thin plate. Although various displacement transducers may be used to measure the bending, these are single-point measurements, and it is difficult to eliminate the error caused by eccentric load and shear force. Error-correction models for the elastic modulus of quartz glass using digital speckle interferometry are proposed for eccentric load and shear force. First, the positional misalignment between maximum deflection and load is analyzed, and the error caused by eccentric load is corrected. Then, the additional displacement caused by shear force at different positions of the quartz glass plate is explored. The effect of shear deformation is also corrected, by measuring two points. Since digital speckle interferometry has the advantage of full-field measurement, it can simultaneously obtain deflection data for multiple points to realize error correction. Experimental results are presented to demonstrate that the proposed model can effectively correct the measurement error of the elastic modulus.

• International Journal of Highway Engineering
• /
• v.16 no.3
• /
• pp.35-41
• /
• 2014

PURPOSES : The dynamic modulus for a specimen can be determined by using either the non-destructed or destructed testing method. The Impact Resonance Testing (IRT) is the one of the non-destructed testing methods. The MTS has proved the source credibility and has the disadvantages which indicate the expensive equipment to operate and need a lot of manpower to manufacture the specimens because of the low repeatability with an experiment. To overcome these shortcomings from MTS, the objective of this paper is to compare the dynamic modulus obtained from IRT with MTS result and prove the source credibility. METHODS : The dynamic modulus obtained from IRT could be determined by using the Resonance Frequency (RF) from the Frequency Response Function (FRF) that derived from the Fourier Transform based on the Frequency Analysis of the Digital Signal Processing (DSP)(S. O. Oyadigi; 1985). The RF values are verified from the Coherence Function (CF). To estimate the error, the Root Mean Squared Error (RMSE) method could be used. RESULTS : The dynamic modulus data obtained from IRT have the maximum error of 8%, and RMSE of 2,000MPa compared to the dynamic modulus measured by the Dynamic Modulus Testing (DMT) of MTS testing machine. CONCLUSIONS : The IRT testing method needs the prediction model of the dynamic modulus for a Linear Visco-Elastic (LVE) specimen to improve the suitability.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.1
• /
• pp.1-7
• /
• 2007

In this paper, the necessary and sufficient conditions for strict positive realness of the rational transfer functions directly from basic definitions in the frequency domain are studied. A new frequency domain approach is used to check if a rational transfer function is a strictly positive real or not. This approach is based on the Taylor expansion and the Maximum Modulus Principle which are the fundamental tools in the complex functions analysis. Four related common statements in the strict positive realness literature which is appeared in the control theory are discussed. The drawback of these common statements is analyzed through some counter examples. Moreover a new necessary condition for strict positive realness is obtained from high frequency behavior of the Nyquist diagram of the transfer function. Finally a more simplified and completed conditions for strict positive realness of single-input single-output linear time-invariant systems are presented based on the complex functions analysis approach.

• The Korean Journal of Ceramics
• /
• v.6 no.1
• /
• pp.37-42
• /
• 2000

To reduce shrinkage and the possibility of fracture during ambient pressure drying, it is of great importance to increase the strength and stiffness of the wet gels. In this paper is presented the strengthening and stiffening of wet silica gels prepared from sodium silicate (water glass) as well as properties of the corresponding xerogels. By washing gels containing different initial silica contents in water solutions at elevated pH, a maximum in shear modulus of ~4 MPa was obtained. The maximum stiffness enabled xerogels with bulk density of 0.28g/$\textrm{cm}^3$ to be made regardless of silica content and washing conditions. However, by aging the wet gels in a solution providing fresh monomers to the gel network, a shear modulus of 20 MPa was obtained after 27h. By this method monolithic xerogels with a density down to ~0.2g/$\textrm{cm}^3$ was prepared. The results are compared to alkoxide based gels.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.251-256
• /
• 2015

In this paper, an systematic approach is presented, in which the bridge-type traffic sign structure is body out by CSDDA PrePost Processor. There is dead load and wind load that is working on the structure which will make force and moment. Analyzied the stress distribution of the standard form and by changing the shape, compared the safety in terms of deflection and stress (with the standard form) to know the effect of each component in the bridge-type traffic sign structure. The safety of deflection and stress is evaluated by maximum distance/100) and ASIC code respectively. The standard form of bridge-type traffic sign structure is established by two pairs of pillar and two pairs of floor beam. Replaced the links which is consist of flange and screws as the torsion spring and nm our analysis program. By adjusting variable of rigidity modulus of torsion spring, moment between column and beam is controled depending on value of rigidity modulus.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.831-835
• /
• 2008

Recently, the use of C.S.G is gradually increasing as the construction material for dam, road, revetment and so on. The strength characteristics of C.S.G is affected by various influence factors such as specimen size, maximum grain size and water contents. Therefore, When designing and constructing the C.S.G structure, it is very important for us to understand the nature of used materials well and to test it's quality. Commonly, C.S.G strength test is used the cylinders specimen size of $15{\times}30$ at KS F2405. But, the specimen size extracted from the field structure is not regular. This paper aims at offering the experimental data about the compressive strength and elasticity modulus by change of the specimen size for the effective quality control of the C.S.G structure.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.5
• /
• pp.392-398
• /
• 2013

This study investigated the effect of test zone selection for evaluating bending strength of visually graded lumber. This will contribute to the understanding of two different methods under different standards. In method I, the major defect was randomly placed in the test specimen. In method II, the major defect was randomly placed in the maximum moment zone (MMZ). The results showed that the method II is more accurate for reflecting the effect of defects governing the grade of lumber. Unless the maximum strength-reducing defect (MSRD) is placed in MMZ, the evaluated value would be higher than that of MSRD. For evaluating the modulus of rupture (MOR) of visually graded lumber in test set-up of Method I, the Eq. (5) needs to be considered.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.5
• /
• pp.59-63
• /
• 2011

Ground dynamic parameter such as shear elastic modulus and damping ratio is a very important variable in design of ground-structure with repeated load and dynamic load. Shear elastic modulus and damping ratio on small strain below linear limit strain is constant regardless of strain. Shear elastic modulus as the maximum shear elastic modulus and damping ratio as the minimum damping ratio were considered. As a lot of experiment related to the maximum shear elastic modulus, which is in dynamic deformation characteristics, have been conducted, many factors including voiding ratio, over consolidation ratio(OCR), confining pressure, geology time, PI, and the number of load cycle affect to dynamic soil characteristic. However, the research of ground dynamic characteristic improved with grout is absent such as underground continuous wall construction, deep mixing method, umbrella arch method. In order to investigate the dynamic soil characteristics improved with grout, in this study, resonant column tests were performed with changing water content(20%, 25%, 30%) and injection ratio of grout(5%, 10%, 15%), cure time(7th day, 28th day) As a result, shear elastic modulus and damping ratio, which are ground dynamic parameter, are affected by the injection ratio of milk grout, cure time and water content.