• Journal of the Korea Concrete Institute
• /
• v.24 no.4
• /
• pp.369-379
• /
• 2012

The collapse of concrete structures by extreme loads such as impact, explosion, and blast from terrorist attacks causes severe property damage and human casualties. Concrete has excellent impact resistance to such extreme loads in comparison with other construction materials. Nevertheless, existing concrete structures designed without consideration of the impact or blast load with high strain rate are endangered by those unexpected extreme loads. In this study, to improve the impact resistance, the static and impact behaviors of concrete beams caste with steel fiber reinforced concrete (SFRC) with 0~1.5% (by volume) of 30 mm long hooked steel fibers were assessed. Test results indicated that the static and impact resistances, flexural strength, ductility, etc., were significantly increased when higher steel fiber volume fraction was applied. In the case of the layered concrete (LC) beams including greater steel fiber volume fraction in the tensile zone, the higher static and impact resistances were achieved than those of the normal steel fiber reinforced concrete beam with an equivalent steel fiber volume fraction. The impact test results were also compared with the analysis results obtained from the single degree of freedom (SDOF) system anaysis considering non-linear material behaviors of steel fiber reinforced concrete. The analysis results from SDOF system showed good agreement with the experimental maximum deflections.

• Korean Chemical Engineering Research
• /
• v.50 no.4
• /
• pp.708-712
• /
• 2012

Ionic liquids (ILs) existing as liquid state at room temperature are composed of a immense heterocyclic cation and inorganic anion which is smaller than cation's size. Thus, the species of cation and anion as well as the length of alkyl group on the cation have influence on their physical properties. Their outstanding properties such as non-volatility, thermal stability and wide range of electrochemical stability make these materials excellent candidates for green solvent which can substitute the conventional organic solvents. In this study, ILs based on imidazolium cation have been synthesized such as 1-butyl-3-methylimidazolium bromide ([BMIM][Br]), 1-butyl-3-methylimidazolium chloride ([BMIM] [Cl]), 1-butyl-3-methylimidazolium iodide ([BMIM][I]), and 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][$BF_4$]). The density, viscosity, refractive index, heat capacity and ionic conductivity of [BMIM][Br], [BMIM][I], and [BMIM] [$BF_4$] were measured over range of temperature of 293.2 to 323.2 K. The density and refractive index values of [BMIM][I] were the highest among three ILs and the viscosity values of [BMIM][Br] were the highest among three ILs. The heat capacities [BMIM][$BF_4$] were higher than those of [BMIM][Br]. The ionic conductivities of [BMIM][$BF_4$] were higher than those of [BMIM][I].

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.103-111
• /
• 2012

One of the basic physical properties of the hardened cement paste, the rigidity, is deteriorated during concrete matrix forming, depending on the replacement rate of the crushed stone powder, and due to drying shrinkage. Therefore, the concrete containing crushed stone powder has been limitedly used as non-structural construction material. To improve these disadvantages, a hydrothermal reaction employing method can be considered. High-temperature and high-pressure water is involved in the hydrothermal reaction in the mixing with specific materials. The rigidity improving mechanism is related to the synthesis of calcium silicate. The calcium silicate is produced through reaction between calcium compounds and the silicic acid. Various kinds of calcium silicate can be produced depending on the CaO/$SiO_2$ mole ratio, the temperature of the hydrothermal synthesis, the pressure, and the reaction time. The product of the synthesis mechanism, tobermorite crystal, plays a pivotal role for the rigidity reinforcement. The crushed stone powder, analyzed in this study, contains 50 to 60% of $SiO_2$ and 10 to 20% $Al_2O_3$. The composite rate is appropriate to create the tobermorite crystal through formation of hardened cement matrix under the hydrothermal synthetic conditions and with the CaO in the cement. Moreover, further reinforcement was promoted using the property of material under the identical density through promoting the formation of tobermorite crystal.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.32 no.1
• /
• pp.24-31
• /
• 2016

Purpose: Many studies have shown that airborne-particle abrasion of fiber post can improve the bonding strength to resin cement. But, airborne-particle abrasion may influence the property of fiber post. The purpose of this study is to evaluate the influence of airborne-particle abrasion on flexural strength of fiber post. Materials and Methods: Two fiber-reinforced posts; DT Light Post Size 2 (1.8 mm diameter, Bisco Inc) and RelyX Fiber Post Size 3 (1.9 mm diameter, 3M ESPE); were used in this study. Each group was divided into 3 subgroups according to different surface treatments; without pretreatment: $50{\mu}m$ aluminum oxide (Cobra$^{(R)}$, Renfert): and $30{\mu}m$ aluminum oxide modified with silica (Rocatec Soft$^{(R)}$, 3M ESPE). After airborne-particle abrasion procedure, three-point bending test was done to determine the flexural strength and flexural modulus. The diameter of each posts was measured to an accuracy of 0.01 mm using a digital micrometer. There was no diameter change before and after airborneparticle abrasion. The mean flexural moduli and flexural strengths calculated using the appropriate equations. The results were statistically analyzed using One-way ANOVA and Scheffe's post-hoc test at 95% confidencial level. Results: There was no significant difference on flexural strength between groups. Conclusion: In the limitation of this study, flexural strength and flexural modulus of fiber post are not affected by airborne-particle abrasion.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.4
• /
• pp.308-313
• /
• 2014

Recently, for longevity of resident building, the main trend is that the change of the inside space organization of resident building from wall construction to rhamen construction, which resulted in increase in use of lightweight composite panel. Thus, in this study, authors analyzed the engineering property of oxide of magnesium depending on the magnesium chloride addition ratio. The results of this research is expected to contribute on providing a fundamental material for the surface materials of lightweight composite panel. As the result of the experiment, as fluidity increased, air content decreased and initial set and final set as the magnesium chloride addition ratio increase. In the aspect of flexural strength and compressive strength, the test specimen showed the highest strength at 40% of the magnesium chloride addition ratio. At 20% of the magnesium chloride addition ratio, the test specimen showed the lowest water absorption rate. As the magnesium chloride addition ratio increases, the expansibility tends to increase as well in the aspect of shrinkage strain. After observing microstructure, we can see hydration products in the form of needle. It appeared high flexural strength because the hydration products have mineral fibrous tissue shape, which also contribute to the cause of the expansibility.

• Economic and Environmental Geology
• /
• v.23 no.2
• /
• pp.201-213
• /
• 1990

Mineralogy, chemistry, physical property, and fossil abundance have been studied for the samples collected from three weathering profiles, two from the Duho Formation and one from the Hagjeon Formation in the Tertiary sediments in the Pohang area. The mineralogy of the samples from the Duho Formation shows somewhat different from that of the Hagjeon Formation. Kaolinite is more abundant and shows higher crystallinity in samples from the Duho Formation than those in the Hagjeon Formation, but clay mineral assemblage in each weathering profile remain fairly constant with depth. This difference in mineral distribution seems to be inherited from original source materials. It indicates that little or not severe leaching has been taking place in these three weathering profiles. Weathering indicies indicate different degrees of susceptibility to chemical weathering in these two formations. The Duho Formation has a higher degree of susceptibility to weathering than that of the Hagjeon Formation which is mainly due to differences in clay mineral assemblages in both formations. A noticeble colour difference between oxidized and unoxidized zones in each profile can be easily recognized which is definetely due to different decomposition rate organic carbon by various oxidation state from surface to bottom of the profile. Weathering process have also intensively influenced microfossil preservation about up to 7-10 m in depth in the Duho Formation. Consequently, characteristics observed at weathering surface should be used as a subsidiary tool in setting geologic boundary or establishing formation. Great care must be taken to choose sampling site for microfossil study.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.5
• /
• pp.25-35
• /
• 2014

The sedimentary rocks exposed around Mt. Palgong were subjected to metamorphism due to a granitic magma intrusion at late Cretaceous, and they eventually metamorphosed to hornfels by the action of both hydrothermal solution and high temperature supplied from the magma. The hornfels zone around the granite body ranges from 2.0 to 3.5 km in width but the boundary between hornfels and sedimentary rocks is not obviously defined because the metamorphic grade gradually decreases with distance from the granite boundary. A series of laboratory tests on 350 core specimens made by 35 fresh rock blocks obtained from 5 selected locations around Mt. Palgong are performed to verify the variation of physical and mechanical properties related to metamorphic grade of the rock. Water content and absorption ratio of the hornfels linearly increase with distance to the granite boundary whereas dry unit weight, p-wave velocity, point load strength, and slake durability index linearly decrease with the distance. These results imply that the metamorphic grade of the hornfels also linearly decrease with the distance to granite boundary. Empirical equations for the variation of properties with the distance to granite boundary and relationship between a property and another one are deduced by regression analyses. And a criteria for classification of hornfels exposed in the study area based on the P-wave velocity and point load strength is proposed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5551-5557
• /
• 2012

Sedimentary rocks dug up in construction fields are mostly stockpiled for landfill disposal, leading to an increase in construction costs and construction inefficiency. After screening, some of the sandstone can be used as aggregate; however, most of the shale ends up as industrial waste in practice. In this study, to stabilize the demand and develop resources for alternative aggregates of concrete, the potential use of shale, which is widely distributed in the Daegu-Kyeongbuk region, as a concrete aggregate was evaluated. Red and black shale exported from a Daegu excavation site was selected for use in the experiments and evaluated by comparing with hornfels, which is widely used as a coarse aggregate and is a type of andesite and metamorphosed sedimentary rock. The physical properties of the aggregate were evaluated in accordance with the test methods of KS F 2527 "crushed concrete aggregate," and the compressive strength against the shale aggregate replacement ratio was measured. The compressive strength of the concrete after 28 days was 30.8 MPa when the black shale replaced 100% of the aggregate in the concrete and 31.1 MPa when the red shale replaced 100% of the aggregate in the concrete. Compared with the compressive strength of 37.5 MPa for concrete prepared by using plain aggregate, using shale as a substitute for the aggregate produced an average compressive strength that was 82% of normal concrete.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.15 no.4
• /
• pp.151-161
• /
• 2012

The purpose of this study was to build a web-server for culture heritages management information system in order to efficiently manage and safely preserve undesignated cultural properties in the Namsan area in Kyeongju, which have been neglected so far. In order to achieve this purpose, data were collected on the basis of undesignated cultural properties in the study area. To acquire the location and range GPS were used and spatial data including geographic coordinates, visual materials and structured interviews were conducted through field survey. In addition, in order to obtained reliable and accurate locations of undesignated cultural properties which are scattered, DGPS(Differential Global Positioning System) were used. The spatial database was constructed based on the standard of cultural properties and attribute data was linked to geo-spatial information(digital map and aerial photographs). This system was built in a web-server environment. The result shows detailed description on the selected output for selected location and property information can be located on the map. In particular, a database to search for the status and modification of cultural properties will provide information to the users.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.9
• /
• pp.418-424
• /
• 2017

Magnesium has a higher specific strength than other metals and is widely used industry wide due to its excellent vibration absorption ability and electromagnetic wave shielding property.For example, it is used for automobile parts such as car seat frames and cylinder heads, and is widely used in electronic products such as notebook cases and mobile phone cases. In addition, it is in the spotlight as a bone-implant material used to assist in the treatment of damaged bones when the bones are cracked or broken. Currently, Ti alloy, stainless steel and Co-Cr-Mo alloy are used as the implant material, and the Mg alloy remains in research stage. The current problem with bone implant implants is that the patients must undergo reoperation to remove the implants after joint surgery. Magnesium, however, can achieve sufficient strength compared to current materials. In addition, since it is self-decomposed after the recovery, reoperation is not necessary. In this paper, Mg alloys were designed by adding harmless Ca and Zn to the human body. In order to improve the strength and corrosion resistance, the final alloy was designed by adding a small amount of Sr as a grain refiner. The radioactive elements of Sr are harmful to the human body, but other naturally occurring Sr elements are harmless. Microstructure analysis of the alloys was performed by optical microscopy and scanning electron microscopy. The mechanical properties and corrosion characteristics were evaluated by tensile test, potentiodynamic test and immersion test.