• ETRI Journal
• /
• 제43권2호
• /
• pp.209-220
• /
• 2021

The filtered orthogonal frequency division multiplexing (F-OFDM) system has been recommended as a waveform candidate for fifth-generation (5G) communications. The suppression of out-of-band emission (OOBE) and asynchronous transmission are the distinctive features of the filtering-based waveform frameworks. Meanwhile, the high peak-to-average power ratio (PAPR) is still a challenge for the new waveform candidates. Partial transmit sequence (PTS) is an effective technique for mitigating the trend of high PAPR in multicarrier systems. In this study, the PTS technique is employed to reduce the high PAPR value of an F-OFDM system. Then, this system is compared with the OFDM system. In addition, the other related parameters such as frequency localization, bit error rate (BER), and computational complexity are evaluated and analyzed for both systems with and without PTS. The simulation results indicate that the F-OFDM based on PTS achieves higher levels of PAPR, BER, and OOBE performances compared with OFDM. Moreover, the BER performance of F-OFDM is uninfluenced by the use of the PTS technique.

• Geomechanics and Engineering
• /
• 제27권5호
• /
• pp.497-509
• /
• 2021

A large deformation FEM (Finite Element Method) based numerical analysis has been performed to study the behaviour of the bell-shaped anchor embedded in undrained saturated (cohesive) soil with the help of finite element based software ABAQUS. A typical model anchor with bell-diameter of 0.125 m, embedded in undrained saturated soil with varying cohesive strength (from 5 kN/m² to 200 kN/m²) has been chosen for studying the characteristic behaviour of the bell-shaped anchor installed in cohesive soil. Breakout factors have been evaluated for each case and verified with the results of experimental model tests for three different types of soil samples. The maximum value of breakout factor was found as about 8.5 within a range of critical embedment ratio of 2.5 to 3. An explicit model has been developed to estimate the breakout factor (F_c) for uplift capacity of bell-shaped anchor within clay mass in terms of H/D ratio (embedment ratio). It was also found that, the ultimate uplift capacity of the anchor increases with the increase of the value of cohesive strength of the soil and H/D ratio. The empirical equation developed in the present investigation is usable within the range of cohesion value and H/D ratio from 5 kN/m² to 200 kN /m² and 0.5 to 3.0 respectively. The proposed model has been validated against data obtained from a series of model tests carried out in the present investigation. From the stress-profile analysis of the soil mass surrounding the anchor, occurrence of stress concentration is found to be generated at the joint of anchor shaft and bell. It was also found that the vertical and horizontal stresses surrounding the anchor diminish at about a distance of 0.3 m and 0.15 m respectively.

• 한국수정란이식학회지
• /
• 제27권1호
• /
• pp.9-14
• /
• 2012

This study was conducted to analyze the transgenic efficiency and sex ratio in ${\alpha}$-1,3-galactosyltransferase (GalT) knock-out (KO) transgenic pigs according to generation. GalT KO piglets were produced by artificial insemination or natural mating. The transgenic confirmation of GalT KO was evaluated by PCR amplification using specific primers. After electrophoresis, three types of bands were detected such as 2.3 kb single band (Wild), 2.3 and 3.6kb double bands (GalT KO -/+; heterozygote), and 3.6kb single band (GalT KO -/-; homozygote). Transgenic efficiency in F1 generation was 64.5% (23/35) of GalT KO (-/+). In F2 generation, GalT KO transgenic efficiency was 36.4% (21/57, Wild), 47.5% (28/57, GalT KO -/+), and 16.1% (8/57, GalT KO -/-), respectively. Interestingly, no homozygote piglets were born in 6 deliveries among total 11 deliveries, although they were pregnant between male (M) and female (F) $F_1$ heterozygote. In the 5 litters including at least one GalT KO -/- piglet, the transgenic efficiency was 13.3% (2/24, Wild), 51.3% (14/24, GalT KO -/+), and 35.3% (8/24, GalT KO -/-), respectively. The sex ratio of M and F was 40:60 in $F_1$ and 49:51 in $F_2$ generation, respectively. Based on these results, GalT KO transgenic pigs have had a reproductive ability with a normal range of transgenic efficiency and sex ratio.

• 한국자기학회지
• /
• 제14권6호
• /
• pp.236-239
• /
• 2004

미소 자유자성층에 인접한 스핀필터층 (SFL; spin filter layer)을 갖는 Ta3/NiFe2/IrMn7/CoFe1/(NOL1)/CoFe2/Cu 1.8/CoFe( $T_{f}$)/Cu( $t_{SF}$ )/(NOL2)/Ta3.5 (두께단위 nm) 구조의 스페큘라 스핀밸브 (SSV; specular spin valve)를 마그네트론 스퍼터링 장치를 사용하여 제작하였다. 반강자성체 I $r_{22}$M $n_{78}$을 속박층으로 한 스핀필터 스페큘라 스핀밸브 (SFSSV; spin filter specular spin valve) 박막에 대하여 자유자성층의 두께 ( $t_{F}$)와 SFL의 두께 ( $t_{SF}$ )가 각각 1.5nm일 때 극대 자기저항 (MR; magnetoresistance)비 11.9%를 얻었으며, $t_{SF}$ 가 1.0nm으로 감소하여도 11%이상의 MR비를 유지하였다. 이것은 나노산화층 (NOL; nano-oxide layer)에 의한 스페큘라 전자와 SFL에 의한 전류분류효과의 증가 때문이다. 또한, 자유자성층과 피속박층 사이의 층간결합장 ( $H_{int}$; interlayer coupling field)은 RKKY력과 정자기결합력으로 설명할 수 있다. 자유자성층의 보자력 ( $H_{cf}$ ; coercivity of the free layer)은 기존의 스핀밸브 (TSV; traditional spin valve)에 비해 현저히 감소했으며, $t_{F}$가 1nm에서 4nm로 변하여도 4 Oe이하의 값을 유지하였다. 따라서 SFL의 삽입으로 자유자성층의 연자성 특성을 떨어뜨리지 않으면서 자유자성층 두께의 감소와 MR비의 향상을 가능하게 하였다.

• Mass Spectrometry Letters
• /
• 제8권1호
• /
• pp.14-17
• /
• 2017

The effect of cationization agent concentration on glycan detection via matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) was investigated using $Na^+$ ions in the form of NaCl as the cationization agent. NaCl solution concentrations ranging from 1 mM to 1 M were investigated. Glycans from ovalbumin were mixed with the cationization agent solution and the 2,5-dihydroxybenzoic acid (2,5-DHB) matrix solution in a volume ratio of 1:1:1. The resulting mixture was loaded onto the MALDI plate. Two MALDI-TOF MS instruments (Voyager DE-STR MALDI-TOF MS and Tinkerbell RT MALDI-TOF MS) were used for detection of glycans. The best detection, in terms of the number of identified glycans, the peak intensity, and the signal-to-noise (S/N) ratio, was obtained with NaCl concentrations of 0.01-0.1 M for both MALDI-TOF MS instruments.

• Steel and Composite Structures
• /
• 제43권6호
• /
• pp.735-757
• /
• 2022

The behavior of shear deficient under-balanced reinforced concrete beams with rectangular cross-sections, which were externally strengthened with CFRP composite along shear spans, was experimentally investigated under vertical load. One of the specimens represents a reference beam without CFRP strengthening and the other specimens have different width/strip spacing ratios (w_f/s_f). The optimum strip in terms of w_f/s_f, which will bring the beam behavior to the ideal level in terms of strength and ductility, was determined according to the regulations. When the w_f/s_f ratio exceeds 0.55, the behavior of the beam shifted from shear failure to bending failure. However, it has been observed that the w_f/s_f ratio should be increased up to 0.82 in order for the beam to reach sufficient shear reserve value according to the codes. It is also observed that the direction and weight of the CFRP composite are one of the most critical factors and 240 gr/m² CFRP strips experienced sudden ruptures in the shear span after the cracking of the concrete. It is considered as a deficiency that the empirical shear capacity formulas given for the beams reinforced with CFRP in the regulations do not take into account both direction and weight of CFRP composites.

• 산업경영시스템학회지
• /
• 제12권19호
• /
• pp.39-47
• /
• 1989

This paper considers a multi-stage flowshop scheduling Problem where the setup times of jots depend on immediately preceding jobs. Three heuristics algorithms, CAMPBELL, PEIDAN and CAMRING are proposed. The performance measure is a minimization of makespan. The parameters of simulation model are PS(ratio of the processing times to setup times), M(number of machines), and N(number of job). This simulation model for each algorithm is a 4$\times$3$\times$3 factorial design with 360 observations. The makespan of the proposed heuristic algorithms is compared with the optimal makespan obtained by the complete enumeration of schedules. This yardstick of comparison is defined as a relative error. The mean relative error of CAMPBELL, PEIDAN, and CAMRING algorithms are 4.353%, 7.908%, and 8.578% respectively. The SPSS, is used to analyse emphirical results. The experimental results show that the three factors are statistically significant at 5% level.

• 센서학회지
• /
• 제10권6호
• /
• pp.295-303
• /
• 2001

형광체로서 ZnS를 사용하고 BST 강유전체 박막을 절연체로 사용한 전계발광소자를 제작하고 그 특성을 조사하였다. 형광체로는 청색 및 녹색발광을 위해 각각 $ZnS:AgF_3$와 ZnS:$TbF_3$를 사용하였으며 적색을 위해 ZnS:Mn과 $ZnS:SmF_3$를 사용했다. 이들의 형광체가 증착 도중에 분해되는 것을 막기 위해 석영관에 그들을 각각 봉입해서 열처리하여 결정화시킨 후에 진공증착원으로 사용하였다. 한편 절연층으로 사용한 BST박막은 $Ba_{0.5}Sr_{0.5}TiO_3$세라믹스 타겟을 사용하여 마그네트론 스퍼터링 방법으로 제조하였다. 이때 기판온도, 분위기압 및 작동기체인 $Ar:O_2$의 비가 각각 $400^{\circ}C$, 30 mTorr 및 9:1이였다. 각 형광체의 두께는 150 nm씩 합계 600 nm였고, 절연층은 상부가 400 nm 및 하두가 200 nm이었다. 이와 같이 만든 박막 전계발광소자의 발광 문턱전압은 $75\;V_{rms}$이고, 최고 휘도는 $100\;V_{rms}$에서 $3200\;cd/m^2$이었다. 그리고 절연층의 유전상수는 1 kHz에서 254이다.

• 대한환경공학회지
• /
• 제28권10호
• /
• pp.1090-1097
• /
• 2006

판지공장 인쇄폐수에 무산소 활성오니공정을 적용한 결과 $TCOD_{Mn}=90{\sim}94%$, $Color=58{\sim}81%$의 높은 제거효율을 얻었다. 산업현장 판지공장 폐수에 대한 무산소 활성오니공정의 설계분석을 위하여 Monod식에 의한 동력학적계수를 추정한 결과 $K_{max}$(최대 기질제거속도)=0.52 $day^{-1}$, $K_s$(반포화 기질농도)=314 mg/L, $K_d$(내생호흡계수)=0.274 $day^{-1}$, y(미생물의 합성계수)=0.908 mg/mg, ${\mu}_{max}$(최대 비생장속도)=0.472 $day^{-1}$로 산출되었다. 설계분석을 위한 부하인자의 값은 F/M비=$0.043{\sim}0.07$ kg-$TCOD_{Mn}$/kg-SS-day, BOD 용적부하=$0.18{\sim}0.3$ kg-$TCOD_{Mn}/m^3-day$, ${\theta}_x$(미생물 체류시간)=$=6.8{\sim}26.4$ day로 현장 검증되었다. 이러한 부하인자의 값을 미생물의 성장 동력학과 연계시켜 볼 때 F/M비는 ${\theta}_x$에 반비례하고, 단위측면에서 F/M비는 ${\mu}_{max}$와 같아야 하나 F/M비와 ${\mu}_{max}$는 상당한 차이가 있음을 알 수 있었다. 따라서 미생물의 성장 동력학을 이용한 무산소 활성오니공정을 설계하고자 할 때에는 충분한 안전율이 요구되는 것으로 사료되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.319-322
• /
• 2003

To match the charge induced by the insulators $CeO_2$ with the remanent polarization of ferro electric SBT thin films, areas of Pt/SBT/Pt (MFM) and those of $Pt/CeO_2/Si$ (MIS) capacitors were ind ependently designed. The area $S_M$ of MIS capacitors to the area $S_F$ of MFM capacitors were varied from 1 to 10, 15, and 20. Top electrode Pt and SBT layers were etched with for various area ratios of $S_M\;/\;S_F$. Bottom electrode Pt and $CeO_2$ layers were respectively deposited by do and rf sputtering in-situ process. SBT thin film were prepared by the metal orgnic decomposition (MOD) technique. $Pt(100nm)/SBT(350nm)/Pt(300nm)/CeO_2(40nm)/p-Si$ (MFMIS) gate structures have been fabricated with the various $S_M\;/\;S_F$ ratios using inductively coupled plasma reactive ion etching (ICP-RIE). The leakage current density of MFMIS gate structures were improved to $6.32{\times}10^{-7}\;A/cm^2$ at the applied gate voltage of 10 V. It is shown that in the memory window increase with the area ratio $S_M\;/\;S_F$ of the MFMIS structures and a larger memory window of 3 V can be obtained for a voltage sweep of ${\pm}9\;V$ for MFMIS structures with an area ratio $S_M\;/\;S_F\;=\;6$ than that of 0.9 V of MFS at the same applied voltage. The maximum memory windows of MFMIS structures were 2.28 V, 3.35 V, and 3.7 V with the are a ratios 1, 2, and 6 at the applied gate voltage of 11 V, respectively. It is concluded that ferroelectric gate capacitors of MFMIS are good candidates for nondestructive readout-nonvolatile memories.