• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1407-1414
• /
• 2016

Unlike existing pulse-width modulation (PWM) techniques, such as sinusoidal PWM and random PWM, the wavelet PWM (WPWM) technique based on a Harr wavelet function can achieve a high fundamental component for the output voltage, low total harmonic distortion, and simple digital implementation. However, the original WPWM method lacks output voltage control. Thus, the practical application of the WPWM technique is limited. This study proposes an improved WPWM technique that can regulate output voltage amplitude with the addition of a parameter. The relationship between the additional parameter and the output voltage amplitude is analyzed in detail. Experimental results verify that the improved WPWM exhibits output voltage control in addition to all the merits of the WPWM technique.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.8
• /
• pp.1465-1470
• /
• 2006

This paper presents a design of low power CMOS LNA(Low Noise Amplifier) for 2.4 GHz ZigBee applications that is a promising international standard for short area wireless communications. The proposed circuit has been designed using TSMC $0.18{\mu}m$ CMOS process technology and two stage cascade topology by current reuse technique. Two stage cascade amplifiers use the same bias current in the current reused stage which leads to the reduction of the power dissipation. LNA design procedures and the simulation results using ADS(Advanced Design System) are presented in this paper. Simulation results show that the LNA has a extremely low power dissipation of 1.38mW with a supply voltage of 1.0V. This is the lowest value among LNAs ever reported. The LNA also has a maximum gain of 13.38dB, input return loss of -20.37dB, output return loss of -22.48dB and minimum noise figure of 1.13dB.

• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.6
• /
• pp.416-424
• /
• 2014

This paper presents an 8-bit pipelined analog-to-digital converter. The supply voltage applied for comparators and other sub-blocks of the ADC were 0.7V and 0.5V, respectively. This low power ADC utilizes the capacitive charge pump technique combined with a source-follower and calibration to resolve the need for the opamp. The differential charge pump technique does not require any common mode feedback circuit. The entire structure of the ADC is based on fully dynamic circuits that enable the design of a very low power ADC. The ADC was designed to operate at 1MS/s in 90nm CMOS process, where simulated results using ADS2011 show the peak SNDR and SFDR of the ADC to be 47.8 dB (7.64 ENOB) and 59 dB respectively. The ADC consumes less than 1mW for all active dynamic and digital circuitries.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.1
• /
• pp.26-28
• /
• 2006

The development technique of digital logic using CMOS device is close reached several limitations These make technical needs that are ultra high speed superconductive systems based on CMOS silicon digital computing technique. Comparing digital logic based on silicon CMOS, the computing technique based on ultra high speed superconductive systems has many advantages which are ultra low power consumption, ultra high operation speed. etc. It is estimated that features like these increasingly improve the possibility of ultra low power and ultra superconductive systems. In this paper digital logics of current CMOS technique and RSFQ superconductive technique are compared with and analyzed.

• ETRI Journal
• /
• v.31 no.6
• /
• pp.717-724
• /
• 2009

This paper describes a 1.2 V 12 b 60 MS/s CMOS analog front-end (AFE) employing low-power and flexible design techniques for image signal processing. An op-amp preset technique and programmable capacitor array scheme are used in a variable gain amplifier to reduce the power consumption with a small area of the AFE. A pipelined analog-to-digital converter with variable resolution and a clock detector provide operation flexibility with regard to resolution and speed. The AFE is fabricated in a 0.13 ${\mu}m$ CMOS process and shows a gain error of 0.68 LSB with 0.0352 dB gain steps and a differential/integral nonlinearity of 0.64/1.58 LSB. The signal-to-noise ratio of the AFE is 59.7 dB at a 60 MHz sampling frequency. The AFE occupies 1.73 $mm^2$ and dissipates 64 mW from a 1.2 V supply. Also, the performance of the proposed AFE is demonstrated by an implementation of an image signal processing platform for digital camcorders.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.1
• /
• pp.81-90
• /
• 2004

The state assignment for a finite state machine greatly affects the delay, area, power dissipation, and testabilities of the sequential circuits. In order to improve the testabilities and power consumption, a new state assignment technique . based on m-block partition is introduced in this paper. By the m-block partition algorithm, the dependencies among groups of state variables are minimized and switching activity is further reduced by assigning the codes of the states in the same group considering the state transition probability among the states. In the sequel the length and number of feedback cycles are reduced with minimal switching activity on state variables. It is inherently contradictory problem to optimize the testability and power consumption simultaneously, however our new state assignment technique is able to achieve high fault coverage with less number of scan nfp flops by reducing the number of feedback cycles while the power consumption is kept low upon the low switching activities among state variables. Experiment shows drastic improvement in testabilities and power dissipation for benchmark circuits.

• Journal of electromagnetic engineering and science
• /
• v.17 no.4
• /
• pp.191-196
• /
• 2017

Microwave wireless power transmission (MWPT) is a promising technique for low and medium power applications such as wireless charging for sensor network or for biomedical chips in case with long ranges or in dispersive media such. A key factor of the MWPT technique is its efficiency, which includes the wireless power transmission efficiency and the radio frequency (RF) to direct current (DC) voltage efficiency of RF-DC converter (which transforms RF energy to DC supply voltage). The main problem in designing an RF-DC converter is the nonlinear characteristic of Schottky diodes; this characteristic causes low efficiency, higher harmonics frequency and a change in the input impedance value when the RF input power changes. In this paper, rather than using harmonic termination techniques of class E or class F power amplifiers, which are usually used to improve the efficiency of RF-DC converters, we propose a new method called "optimal input impedance" to enhance the performance of our design. The results of simulations and measurements are presented in this paper along with a discussion of our design concerning its practical applications.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.181-184
• /
• 2005

Operating conditions of photovoltaic power generator is very sensitive to the PV modules. The PV module's control is an importance issue in the removing DC ripple noise. In this paper, the phase-shifted-carrier technique, which is a new three-step dc-dc power multi-converter schemes, is applied to solar generator system to improve the output current waveform. The novel type of three-step dc-dc converter presented has many features such as the good output waveform, high efficiency, low switching losses, low acoustic noise. The circuit configuration is constructed by the conventional full-bridge type converter circuit using the isolated DC power supply for which the solar cell is very suitable. In the end, a circuit design for understanding three-step dc-dc converter and new solar power system were presented

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.9
• /
• pp.1045-1049
• /
• 2010

In this paper, we proposed an ultra-low power low noise amplifier(LNA) using a TSMC 0.18 ${\mu}m$ RF CMOS process. To satisfy the low power consumption with high gain, a current-reused technique is utilized. In addition, a low bias voltage in the subthreshold region is utilized to achieve ultra low power characteristic. The designed LNA has the voltage gain of 13.8 dB and noise figure(NF) of 3.4 dB at 2.4 GHz. The total power consumption of the designed LNA is only 0.63 mW from 0.9 V supply voltage and chip occupies $1.1\;mm{\times}0.8\;mm$ area.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.50-52
• /
• 2019

Dynamic resistance equalization is a viable technique to balance SOC of cells in a parallel-connected battery configuration due to high equalization performance, simplicity and low-cost. However, an inappropriate design of the equalization resistor can degrade the equalization performance and increase the power loss. This paper proposes an optimization process to design the equalization resistors to minimize power loss and equalization error. The simulation results show that the optimally designed resistor significantly enhance the performance in comparison with the conventional fixed-resistor equalization.