• International Journal of Air-Conditioning and Refrigeration
• /
• 제12권4호
• /
• pp.206-213
• /
• 2004

Cycle test for developed phase change material (PCM) is necessary in order to assess the variation of latent heat, which decreases with time by deterioration. T-history method and measurement using heat-flux meter are appropriate for the cycle test in a tube filled with PCM because they do not need an extraction of sample in measuring heat of fusion. In the present study, these methods were applied to a PCM having a melting point below a room temperature, different to the past studies for PCMs melting above a room temperature. As a result of experiment using pure water as specimen, we can obtained rea-sonable values for heat of fusion.

• 설비공학논문집
• /
• 제15권7호
• /
• pp.604-610
• /
• 2003

Cycle test for developed phase change material (PCM) is necessary in order to analyze the variation of latent heat, which decreases with time by deterioration. 7-history method and measurement using heat flux meter are appropriate for the cycle test in a tube filled with PCM because they do not need an extraction of sample in measuring the heat of fusion. In the present study, these methods were applied to a PCM having a melting point below a room temperature, different from the past studies for PCMs melting above a room temperature. As a result of experiment using pure water as specimen, we can obtain reason-able values for heat of fusion by both methods.

• 한국가시화정보학회지
• /
• 제22권1호
• /
• pp.6-17
• /
• 2024

This study examined the natural convection heat flow characteristics of the melting process of PCM (palm oil) inside a liquid flexitank(bag) for a cargo container. A film heating element was installed on the bottom of the container, and numerical analysis was performed under heat flux conditions of 1,000 to 4,000 W/m². As a result, the melt interface of the PCM rises to a nearly horizontal state over time. In the initial stage, conduction heat transfer dominates, but gradually waves at the cell flow and melt interfaces are formed due to natural convection heat transfer. As melting progresses, the Ra number increases parabolically, and the Nu number increases linearly and has a constant value. The Nu number rises slowly under low heat flux conditions, whereas under high heat flux conditions, the Nu number rises rapidly. As the heat flux increases, the internal temperature oscillation of the liquid phase after melting increases. However, under high heat flux conditions, excess heat exceeding the latent heat is generated, and the temperature of the molten liquid is raised, so the increase in melting rate decreases. Therefore, the appropriate heating element specification applied to a 20-ton palm oil container is 2,000 W/m².

• 대한기계학회논문집B
• /
• 제40권1호
• /
• pp.1-7
• /
• 2016

환원제를 이용하여 배기가스 내의 NOx를 질소로 환원시키는 요소수 SCR 시스템은 다른 후처리 장치들 중에서 가장 효율적인 장치로 알려져 있다. 차량에 적용되는 SCR 장치는 32.5wt%의 공융혼합물을 이용한다. 이러한 혼합물의 가장 큰 장점 중의 하나는 $-11.7^{\circ}C$에서 얼기 때문에 추운 환경에서 응고를 피할 수 있다는 것이다. 한편, 이러한 추운 환경에서 시동시 필요한 수용액을 충분히 공급하기 위해서는 고체상을 가열해야 한다. 따라서 본 연구에서는 Fluent 상용코드를 이용하여 3차원 비정상 전산해석을 통한 냉각수 및 전기가열 방식에 따른 고체상 요소수의 시간에 따른 액상비 및 온도분포와 같은 해동 및 열전달 특성을 고찰하였다. 본 연구를 통하여 전기히터 가열 방식이 냉각수 방식보다 효율적임을 확인하였다.

• 한국염색가공학회지
• /
• 제25권2호
• /
• pp.110-117
• /
• 2013

The purpose of this study is to fabricate the flame retardant polyester fabric by thermal bonding with low melting component of flame retardant bicomponent filament(LMFRPC) and to describe the characteristics of thermal bonded fabrics. The fabrics were prepared with flame retardant polyester filaments(FRP) as warp and blended filaments of FRP and LMFRPC as weft. The LMFRPC have a sheath and a core wherein the core comprises a flame retardant polyester and the sheath comprises a thermoplastic polyester of low-melting point. In this study, we investigated the physical properties, melting behavior of filament, the effect of the component of FRP and LMFRPC on the thermal bonding, mechanical properties. Melting peak of LMFRPC showed the double melting peak. The thermal bonding of the fabric formed at lower melting peak temperature of bicomponent filament of LMFRPC. The optimum thermal bonding conditions for fabrics was applied at about $170^{\circ}C$ for 60 seconds by pin tenter. On the other hand, the tensile strength, elongation, and LOI of the fabric increased with an increasing component of FRP of weft.

• 한국주조공학회지
• /
• 제5권4호
• /
• pp.243-257
• /
• 1985

Many authors have studied the solidification process of cast iron and the effect of grain boundaries in austenite shell on the growth of spheroidal graphite. But, the studies on the melting morphology of cast iron are rare and the effect of grain boundaries in austenite shell on the melting procedure of spheroidal graphite cast iron is unknown. Therefore, in this work, the melting procedure of cast iron and the role of grain boundaries in austenite shell on the melting of spheroidal graphite have been studied. The main results are summarized as follows. 1. In white cast iron containing silicon, melting initiates at the interface between austenite matrix and temper carbon which was decomposed from $Fe_3C$ during heating. 2. In gray cast iron, melting initiates at the boundary of eutectic cell where elements with low melting temperature are condensed. The dissolution of kish graphite is difficult. 3. In spheroidal graphite cast iron containing little phosphor, melting initiates at the outer region of austenite shell in which silicon is condensed. In this case, grain boundaries in austenite shell give little effect on the melting procedure of spheroidal graphite. 4. In spheroidal graphite cast iron containing phosphor above 0.3 wt%, its melting phenomena are changed with heating rate due to the existence of steadite. In this case, it can be concluded that liquid phase of steadite, which segregated on outer region of austenite shell, moves to spheroidal graphite-austenite interface along the grain boundaries in austenite shell.

• 한국조명전기설비학회지:조명전기설비
• /
• 제11권6호
• /
• pp.74-80
• /
• 1997

본 논문에서는 저압 배전용 전선퓨즈의 I-t 특성을 다루었다. 전선퓨즈 엘리먼트는 과전류 영역을 담당하는 낮은 온도 용융영역(LTME)과, 대전류 영역을 담당하는 높은 온도 용융영역(HTME)으로 나누어 진다. 이들부분에 의하여 퓨즈의 용단특성이 결정되는 것이다. 따라서 이들 부분에 대한 열적, 전기적인 특성을 시뮬레이션하므로서, 퓨즈 엘리먼트 설계의 타당성을 이론적으로 검증하였다. 유한요소법(Finite Element Method)을 이용하여 전선퓨즈의 I-t특성을 시뮬레이션 하였다. 그리고 시뮬레이션 결과와 실혐결과를 비교해 보았을 때 대전류영역과 소전류영역에서의 상당히 유사한 결과를 얻을 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제37권1호
• /
• pp.74-78
• /
• 2024

We have studied the effects of Ag on the characteristics of Sn₄₈In₅₂Ag_x (wt%) low-melting solders for photovoltaic ribbons. The Sn₄₈In₅₂ (wt%) solder coexisted in the InSn₄ and In₃Sn alloys. Ag atoms added in the solder formed an AgIn₂ alloy by reacting with some part of In atoms, while they did not react with Sn atoms. The addition of Ag atoms in the Sn₄₈In₅₂Ag_x (wt%) solders showed useful results; an increase in peel strength and a decrease in melting temperature. The peel strength of the ribbon plated with the Sn₄₈In₅₂ (wt%) solder was 53.6 N/mm², and that of the Sn₄₈In₅₂Ag₁ (wt%) solder largely increased to 125.1 N/mm². In the meanwhile, the melting temperature of the Sn₄₈In₅₂ (wt%) solder was 119.2℃, and that of the Sn₄₈In₅₂Ag₁ (wt%) solder decreased to 114.0℃.

• 마이크로전자및패키징학회지
• /
• 제19권1호
• /
• pp.17-24
• /
• 2012

Recently, flip chip interconnection has been increasingly used in microelectronic assemblies. The common Flip chip interconnection is formed by reflow of the solder bumps. Lead-Tin solders and Tin-based solders are most widely used for the solder bump materials. However, the flip chip interconnection using these solder materials cannot be applied to temperature-sensitive components since solder reflow is performed at relatively high temperature. Therefore the development of low temperature bonding technologies is required in these applications. A few bonding techniques at low temperature of $150^{\circ}C$ or below have been reported. They include the reflow soldering using low melting point solder bumps, the transient liquid phase bonding by inter-diffusion between two solders, and the bonding using low temperature curable adhesive. This paper reviews various low temperature bonding methods.

• 한국식생활문화학회지
• /
• 제23권4호
• /
• pp.499-506
• /
• 2008

This study was conducted to determine the quality characteristics of grape jellies for the elderly. The jellies contained sugar (control) or sugar derivative sweeteners (erythritol, isomaltooligosaccharide, sorbitol, and xylitol). Agar (0.31%) and $\kappa$-carrageenan (0.27%) were the gelling agents. The average age of the subjects participating in the acceptance test was 79. The lightness (L), redness (a), and yellowness (b) values of the agar gel with erythritol mostly decreased, indicating a darker and pale red color. The L and b values of the carrageenan gel with sugar derivative sweeteners increased, indicating brighter and yellowish color. The agar and carrageenan gels with sorbitol showed higher gelling and melting temperature, indicating that gelation occurred easily and did not easily melt. The agar and carrageenan gels with xylitol showed a low-melting temperature, indicating low stability with temperature change. The break-down rate of the agar and carrageenan gels with erythritol was low, whereas that of agar gel with sorbitol was relatively high despite its high melting temperature. Hardness, cohesiveness, gumminess, and chewiness of the gels with sugar derivative sweeteners decreased, and this tendency was most distinct with isomaltooligosaccharide in the agar gel and with sorbitol in the carrageenan gel. The rupture properties of the gel were the same as the hardness of the gel. Sensory acceptance of the agar gels with erythritol, sorbitol, isomaltooligosaccharide, and the carrageenan gel with erythritol was fairly high, whereas that of the agar gel with xylitol and the carrageenan gel with isomaltooligosaccharide and xylitol was low. The results show that sorbitol and erythritol are appropriate as sugar substitutes in grape jellies for the elderly about the acceptability and stability of the gels.