• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.6
• /
• pp.454-464
• /
• 2023

This paper proposes a low-power 8-bit asynchronous SAR ADC with a sampling rate of 1 MS/s for sensor node applications. The ADC uses bootstrapped switches to improve linearity and applies a VCM-based CDAC switching technique to reduce the power consumption and area of the DAC. Conventional synchronous SAR ADCs that operate in synchronization with an external clock suffer from high power consumption due to the use of a clock faster than the sampling rate, which can be overcome by using an asynchronous SAR ADC structure that handles internal comparisons in an asynchronous manner. In addition, the SAR logic is designed using dynamic logic circuits to reduce the large digital power consumption that occurs in low resolution ADC designs. The proposed ADC was simulated in a 180-nm CMOS process, and at a 1.8 V supply voltage and a sampling rate of 1 MS/s, it consumed 46.06 𝜇W of power, achieved an SNDR of 49.76 dB and an ENOB of 7.9738 bits, and obtained a FoM of 183.2 fJ/conv-step. The simulated DNL and INL are +0.186/-0.157 LSB and +0.111/-0.169 LSB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4C
• /
• pp.283-289
• /
• 2005

In this paper, we propose two efficient symbol detection algorithms for space-frequency OFDM (SF-OFDM) transmit diversity scheme. When the number of sub-carriers in SF-OFBM scheme is small, the interference between adjacent sub-carriers may be generated. The proposed algorithms eliminate this interference in a parallel or sequential manlier and achieve a considerable performance improvement over the conventional detection algorithm. The bit error rate (BER) performance of the proposed detection algorithms is evaluated by the simulation. In the case of 2 transmit and 2 receive antennas, at $BER=10^{-4}$ the proposed algorithms achieve the gain improvement of about 3 dB. The symbol detectors with the proposed algorithms are designed in a hardware description language and synthesized to gate-level circuits with the $0.18{\mu}m$ 1.8V CMOS standard cell library. With the division-free architecture, the proposed SF-OFDM-PIC and SF-OFDM-SIC symbol detectors can be implemented using 140k and 129k logic gates, respectively.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.3
• /
• pp.27-33
• /
• 1993

This paper presents the &tal controller for driving high frequency voltage fed PWM inverter that carrier frequency is over 2OkHz.We analyzed the conventional PWM to select a proper PWM pattern. as the result, obtained PWM pattern of the controller in which asynchronus staircase sinusoidal waveform is used as reference signal, and variable carrier ratio method was used for PWM control. The PWM controller is designed by fully digital method. Especially, Thk proposed controller is consisted of 8 bit one-chip microprocessor and digital logic. the former is for arithmetic and data processing, and the latter is for PWM pattern synthesis. Therefore, The responsibility and controllability is improved. Also, Data processing capability is improved using proper program to output modulation index with 9 bits. Circuits configuration of digital controller are made up of one chip 8051 and EPLD, and its controllability is tested by operating voltage fed inverter. Harmonics and current waveform is evaluated and analyzed for the voltage fed inverter system.

• Journal of IKEEE
• /
• v.8 no.2 s.15
• /
• pp.172-180
• /
• 2004

In this paper, a parallel Input/Output modulo multiplier, which is applied to AOTP(All One or Two Polynomials) multiplicative algorithm over $GF(3^m)$, has been proposed using neuron-MOS Down-literal circuit on voltage mode. The three-valued input of the proposed multiplier is modulated by using neuron-MOS Down-literal circuit and the multiplication and Addition gates are implemented by the selecting of the three-valued input signals transformed by the module. The proposed circuits are simulated with the electrical parameter of a standard $0.35{\mu}m$CMOS N-well doubly-poly four-metal technology and a single +3V supply voltage. In the simulation result, the multiplier shows 4 uW power consumption and 3 MHzsampling rate and maintains output voltage level in ${\pm}0.1V$.

• Transactions of the KSME C: Technology and Education
• /
• v.4 no.1
• /
• pp.63-71
• /
• 2016

Although mechatronics education in a mechanical engineering curriculum is recently recognized as important, its experimental education has been done generally in the laboratory equipped with all the apparatus and could not be done at home by students. This paper introduces experimental educations on mechatronics, e.g., digital logic circuits, 7-segment LED drive, square wave generation, microcontroller programming using assembly and C languages, timer interrupt, and step motor drive using a small 5 V power supply, a breadboard, various electronic and electric components, a microcontroller and its programmer, a step motor, and a student's PC. In the developed mechatronics course, experimental educations are scheduled in parallel with content's lectures together, and cheap and economic experimental environment is prepared for students in which students can easily practice experimental works in advance or later at home by themselves.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.11
• /
• pp.2541-2547
• /
• 2010

In this paper, we propose a design technique which replaces logic transistors of 1.2V with medium-voltage transistors of 3.3V having small off-leakage current in repetitive block circuits where speed is not an issue, to implement a low-power eFuse OTP memory IP in the stand-by state. In addition, we use dual-port eFuse cells reducing operational current dissipation by reducing capacitances parasitic to RWL (Read word-line) and BL (Bit-line) in the read mode. Furthermore, we propose an equivalent circuit for simulating program power injected to an eFuse from a program voltage. The layout size of the designed 512-bit eFuse OTP memory IP with a 90nm CMOS image sensor process is $342{\mu}m{\times}236{\mu}m$. It is confirmed by measurement experiments on 42 samples with a program voltage of 5V that we get a good result having 97.6 percent of program yield. Also, the minimal operational supply voltage is measured well to be 0.9V.

• Journal of the Korea Computer Industry Society
• /
• v.2 no.2
• /
• pp.219-228
• /
• 2001

This paper presents the implementation of comparator which are Fail-Safe with respect to faults caused by any single physical defect likely to occur in NMOS and CMOS integrated circuit. The goal is to use it at the Fail-Safe system. First, a new fault model for PLA(Programmable Logic Array) is presented. This model reflects several physical defects in VLSI circuits. It focuses on designs based on PLA because VLSI chips are far too complex to allow detailed analysis of all the possible physical defects that can occur and of the effects on the operation of the circuit. Second, this paper show that these design, which was implemented with 2 level AND_ORor NOR-NOR circuit, are optimal in term of size. And it also present a formal proof that a comparator implemented as NOR-NOR PLA, based on these design, is self-testing with respect to most single faults in the presented fault model. Finally, it discuss the application of the self-testing comparator as a building block for implementing Fail-Safe Adder.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.499-503
• /
• 2000

The use of Multiple-Valued FFT(Fast fourier Transform) is extended from binary to multiple-valued logic(MVL) circuits. A multiple-valued FFT circuit can be implemented using current-mode CMOS techniques, reducing the transitor, wires count between devices to half compared to that of a binary implementation. For adder processing in FFT, We give the number representation using such redundant digit sets are called redundant positive-digit number representation and a Redundant set uses the carry-propagation-free addition method. As the designed Multiple-valued FFT internally using PD(positive digit) adder with the digit set 0,1,2,3 has attractive features on speed, regularity of the structure and reduced complexities of active elements and interconnections. for the mutiplier processing, we give Multiple-valued LUT(Look up table)to facilitate simple mathmatical operations on the stored digits. Finally, Multiple-valued 8point FFT operation is used as an example in this paper to illuatrates how a multiple-valued FFT can be beneficial.

• Journal of Korea Multimedia Society
• /
• v.13 no.7
• /
• pp.943-949
• /
• 2010

This paper presents some improvements on VLSI implementation of lifting-based 9/7 wavelet transform by optimization hardware multiplication. The proposed solution requires less logic area and power consumption without performance loss compared to previous wavelet filter structure based on lifting scheme. This paper proposes a better approach to the hardware implementation using Lefevre algorithm based on extensions of Pattern search methods. To compare the proposed structure to the previous solutions on full multiplier blocks, we implemented them using Verilog HDL. For a hardware implementation of the two solutions, the logical synthesis on 0.18 um standard cells technology show that area, maximum delay and power consumption of the proposed architecture can be reduced up to 51%, 43% and 30%, respectively, compared to previous solutions for a 200 MHz target clock frequency. Our evaluation show that when design VLSI chip of lifting-based 9/7 wavelet filter, our solution is better suited for standard-cell application-specific integrated circuits than prior works on complete multiplier blocks.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.500-509
• /
• 2007

In this paper, we propose a novel pc-based 8-channel USB interface digital multi-controller (DMC) has capacity to be able to adjust ultrasonic motor's (USM's) the parameters-frequency, amplitude, phase difference using FPGA. The proposed DMC can control parameters directly by digital logic through a FPGA. Since it has counter circuit for rotary encoder to measure position and velocity of USM, the other separate circuits are unnecessary. Therefore, it could reduce the size of controller and the production cost. Finally, to verify the performance of proposed DMC, we tested the speed characteristic of two types USM with no-load as adjusting the parameters.