분무철포립자(噴霧撤布粒子)의 연구(硏究)에 있어서 공기중(空氣中)에 표류하고 있는 분무립자(噴霧粒子)의 직경(直徑)을 직접(直接) 측정(測定)하기 어려우므로 입자(粒子)자국의 직경(直徑)과의 비(比)인 확산비(擴散比)(Spread factor)를 이용(利用)함이 일반적(一般的)이다. 물에 Geigy Red Herbicide 물감을 0.5%로부터 2%까지의 중량비(重量比)로 혼합하여 분무액(噴霧液)을 준비하고 균일(均一)한 크기의 입자발생장치(粒子發生裝置)로 발생(發生)한 공기중(空氣中)의 표류 입자(粒子)의 직경(直徑)을 측정(測定)하고 이들 입자(粒子)들을 바로 표본기지(標本期紙) 또는 Eucalypt 잎위에 받아서 입자(粒子)자국의 직경(直徑)들을 측정(測定)하여 입자(粒子)자국의 직경(直徑) 대(對) 공기중(空氣中)의 표류입자(粒子)의 직경(直徑)의 비(比)인 확산비(擴散比)를 구(求)한 결과(結果) 다음과 같은 결론(結論)을 얻었다. 공기중(空氣中)의 표류입자(粒子)의 직경(直徑)과 Kromekote 용지(用紙) 또는 Eucalypt 잎위에 살포(撒布)된 입자(粒子)자국직경(直徑)의 상관성(相關性)의 방정식(方程式)의 일반형(一般形)은 지수방정식(指數方程式)인 $Y=aX^b$로서 log-log 그라프용지(用紙) 상(上)에 직선관계식(直線關係式)으로 나타났다. 엷은 농도 용액의 확산비가 진한 농도 용액의 확산비 보다 일반적(一般的)으로 크게 나타났다. Eucalypt 잎 상(上)에서의 확산비는 용액이 잎속으로 침투하고 엽면(葉面)의 오목한 기공(氣孔)을 가진 표면(表面)으로 인(因)하여 Kromekote 용지(用紙) 상(上)의 확산비보다 상당히 작게 나타났다. Eucalypt 잎 상(上)에 낙하된 입자(粒子)의 평균(平均)두께 추정식(推定式)은 $Y=aX^b$로서 확산비의 상관식(相關式)과 같은 형(形)이었고 이 식(式)은 병충해방제(病蟲害防除) 최소직경(最小直徑)의 입자(粒子)를 기준(基準)할 때 이기준치(基準値)보다 큰 입자(粒子)를 살포(撒布)하는 경우에 있어서 입자(粒子)가 클수록 과잉살포결과를 초래하고 있음을 의미(意味)하고 있다.
본 연구에서는 벌도작업에서의 현실성 있는 품셈 적용기준을 마련하기 위해 잣나무 간벌 작업지에서의 간벌 단계별 벌도작업 공정을 분석하고자 하였다. 이를 위해 4개 잣나무 간벌 작업지에서 체인톱을 이용한 벌도작업 공정조사를 실시하였다. 벌도작업의 작업공정을 예측하기 위해 평균 벌도작업시간 예측 추정식을 개발하였으며, 이를 이용하여 간벌단계별 작업공정을 분석하였다. 연구대상지에서의 잣나무 1본의 평균 벌도작업시간은 약 463초/cycle인 것으로 나타났으며, 시간당 작업공정은 약 $2.26m^3/hr$으로 분석되었다. 잣나무의 간벌단계는 생산목표를 소경재, 중경재, 그리고 대경재로 구분하고, 각 생산목표에 따라 간벌횟수와 시기를 설정하여 작업공정을 분석하였다. 소경재 생산에서는 1회의 간벌을 실시하며, 이때 평균 흉고직경이 16 cm로 작업공정은 약 $8.94m^3$/인${\cdot}$일로 분석되었다. 중경재와 대경재 생산에서는 각각 2회와 3회의 간벌을 실시하며, 1차, 2차 간벌시기는 동일하며, 이때 평균 흉고직경이 16 cm와 21 cm이고, 1일 작업공정은 $9.06m^3$/인${\cdot}$일과 $10.86m^3$/인${\cdot}$일이다. 대경재 생산의 3차 간벌에서는 평균 흉고직경이 30 cm, 1일 작업공정이 $15.12m^3$/인${\cdot}$일로 예측되었다. 이와 같이 간벌단계에 따라 작업공정에서 차이가 나타나고 있으며, 향후 숲가꾸기 품셈적용 기준에 새롭게 반영하기 위한 수종별 벌도작업 공정조사가 요구되고 있다.
A comparison between the productivity of the evergreen needle pine(Pinus densiflora) and of the deciduous broad leaved oak(Quercus mongolica) stands, which is located near Choon-Chun city, Kangwon dist. have been established. The pine stand had a stand density of 938 trees per ha and oak stand had of 638 trees per ha. The diameter at breast height (D) and the height of tree (H) of each tree were measured in sample plot of 800$m^2$. Twelve standard sample trees chose from the sample area felled down, and then weighed the stem, branches and leaves separately, according to both the stratified clip technique and the stem analysis. The vertical distribution of photosynthetic system was arranged effectively for high productivity in the productive structure of both trees. The allometric relation between D2H and dry weight of stem (Ws), branches (Wb) and leaves (Wl) of pine were approximated by log Ws=0.6212 log D2H-0.5383 log Wb=0.4681 log D2H-0.7236 log Wl=0.2582 log D2H-5.1567 and those of oak were approximated by log Ws=0.5125 log D2H+0.0231 log Wb=0.5125 log D2H-0.3755 log Wl=0.8721 log D2H-2.9710 From the above, the standing crops of pine and oak in the sample area were estimated to be as much as 38.83ton and 48.11 ton of dry matter, above ground, per ha, respectively. Annual net production as the sum of the biomass newly formed during one year was appraised at 12.66ton/ha.yr in pine stand and at 8.74 ton/ha.yr in oak. The reason of high productivity of pine stand compared with oak might be resulted from much more about 4 times of the amount of the photosynthetic system, but less non-photosynthetic one of pine than those of oak. To increase the productivity of the forest stands investigated it was necessary to make densly a stand density, to be abundant in the inorganic nutrients and to preserve much water in soil to conserve the litters.
Self-thinning was measured in Salix communities on Bam Island in Seoul at various age stages. $D^2H$ was used to estimate tree biomass, where D is stem diameter at breast height or 10 cm height for plants with height <1.5 m, and H is height. A log-log plot of density versus $D^2H$ and correlation analysis indicated a significant relationship between density and biomass with equation 'log $D^2H$ = -1.27 log N + 7.06'. This indicates that self-thinning affects biomass in the Salix community with -1.27 as the thinning coefficient. If we assume a thinning exponent -3/2, then the allometric coefficient of the equation, log w = a log $D^2H$ + b, is 1.18. This is much higher than that for any other species studied in Korea. There were statistically significant relationships between age and density and between age and basal area and these relationships suggest guidelines for transplantation of willows and for the assessment of Salix community restoration projects in riverine wetlands based on standard density, basal area, and age. The results of this study may also increase understanding of succession processes in Salix community restoration in riverine wetlands.
This study was carried out to figure out the number of logs for sawtimber by DBH and height class and to compare merchantable volume ratio by categorizing into sawtimber, lagging board and pulpwood, and others for Pinus densiflora, Pinus koraiensis, and Larix kaempferi. Logs for sawtimber were hardly produced in small DBH class of three species, but produced evidently from medium DBH class. In large DBH class, the number of logs for sawtimber were noticeably different among species: 4.3 logs for L. kaempferi, 2.6 logs for P. densiflora, and 1.0 logs for P. koraiensis on average. Similarly, merchantable volume ratio for sawtimber were largely different among species in large DBH class with higher than 15 m: 82% logs for L. kaempferi, 60% logs for P. densiflora, and 44% logs for P. koraiensis. When compared to the upper diameter and upper height by species with regard to the last log of a tree produced for sawtimber, upper diameter was smallest with 14.1 cm and upper height was highest with 12.2 m in L. kaempferi. Overall, L. kaempferi was considered as the more commercial species for sawtimber production than P. densiflora and P. koraiensis.
본 연구는 우리나라에서 가장 널리 분포하는 활엽수종인 신갈나무에 대해 흉고직경과 수고 인자를 이용하여 신갈나무의 지상부 및 지하부 바이오매스 상대생장식을 유도하였고, 임분의 바이오매스와 에너지량을 추정하였다. 20-60년생 신갈나무림에서 총 18본의 표본목을 선정하여 벌채하였고, 흉고직경, 수고, 연령, 각 부위(수간, 변재, 심재, 수피, 가지, 잎, 뿌리)별 바이오매스를 측정하였다. 지상부의 각 측정인자들과 지하부 바이오매스 사이에는 높은 상관관계가 나타났다. 지상부 바이오매스의 상대생장식은 $log\;W_A\;=\;1.469\;+\;0.992\;log\;D^2H\;(R^2 =0.99)$, 지하부 바이오매스의 상대생장식은 $log\;W_R\;=\;1.527\;+\;0.808\;log\;D^2H\;(R^2\;=\;0.97)$로 추정되었다. 변재, 심재, 수피, 잎, 뿌리의 평균 에너지량(건중량 기준)은 각각 19,594J/g, 19,571J/g, 19,999J/g, 20,664J/g, 19,273J/g으로 측정되었다. 본 연구 결과는 흉고직경과 수고 인자를 가지고 20년생부터 60년생 신갈나무 임분의 바이오매스와 에너지량을 추정하는데 이용될 수 있다.
This study was carried out to investigate the strength and technical feasibility of glulam from small diameter Pinus densiflora and Larix kaempferi. Small diameter logs are currently not used in structural laminated beam construction, but it is suggested that its properties may be feasible for this purpose. The glulam combinations were designed with high grade laminae located at outer laminations (face) and low grade laminae located at center laminations. Important problems of finger jointed glulam as a structural beam are the small modulus of rupture (MOR). One solution for this problem Mi to use veneer and solid wood as the face laminae. The MOE values were predicted for each beam from laminae. The results showed that actual beam MOE values exceeded slightly the predicted values. Based on the evaluation and analysis of Pinus and Larix glulam, the maximum load of Larix kaempferi glulam indicated large values. The bending properties of A and E types glulam were superior to others. It is suggested that this small diameter log can be a candidate for structural glulam construction, providing the proper combinations of face laminae.
직경 20~30 cm의 원목을 마이크로파 건조하여, 건조속도와 건조 후 목재의 결함이나 문제점 등 원목의 건조 특성을 파악함으로써 마이크로파에 의한 원목건조조건을 최적화하고자 하였다. 출력 20 kw의 마이크로파 건조기는 건조 중 원목 내부온도에 기준하여 제어하였다. 소나무 원목의 경우 원목 내부온도가 $120^{\circ}C$를 초과하지 않도록 제어한 결과 48시간 이내에 함수율 20% 미만까지 안전한 건조가 가능하였다. 건조곤란 수종의 하나인 참죽나무의 원목 경우 표면할렬이 심각하게 발생하여 원목상태로의 건조가 불가능하였다. 원목의 건조속도는 원목의 초기함수율이 높을수록 빨라짐을 보였다.
Jeong, Gi Young;Lee, Jun-Jae;Yeo, Hwanmyeong;Lee, So Sun
Journal of the Korean Wood Science and Technology
/
제44권6호
/
pp.809-820
/
2016
The goal of this study was to predict lamina yield from logs of different diameter for production of cross laminated timber. Log characteristics of red pine (Pinus densiflora) and Japanese cedar (Cryptomeria japonica), including diameter, length, volume, and defects were used for statistical and geometrical analyses, along with the lamina characteristics, including width, thickness, and defects. Based on the data obtained, the strong factors influencing the yield and grade of lamina from the two species were statistically evaluated. A geometrical approach was used for analysis of the yield from logs of given diameters. Statistical analysis showed that lamina yield was dependent on target lamina size but the grade of lamina was not related to any of the log characteristics. The suggested yield equations from the geometrical approach indicated an accuracy of less than 20% difference.
본 논문에서는 위상 배열안테나 급전부를 포함한 반사판 안테나의 빔포밍 특성을 연구하였다. 제안된 안테나의 반사판의 직경, F/D, 급전부의 배열 소자수가 변함에 따라 반사판에 의해 형성되는 빔의 조향각을 계산함으로써 안테나의 빔포밍 특성을 확인하였다. 또한 실제 측정을 통해 제안된 안테나의 빔포밍 특성을 확인하기 위해 직경 1.5 m의 반사판, LPDA(Log Periodic Dipole Array) 4소자로 구성된 급전부를 이용하여 빔포밍 성능을 확인하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.