• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.353-356
• /
• 2002

Planar laser induced fluorescence(PLIF) has been widely used to obtain two dimensional fuel distribution. Preliminary investigation was performed to measure quantitative air excess ratio distribution in an engine fueled with LPG. It is known that fluorescence signal from acetone as a fluorescent tracer is less sensitive to oxygen quenching than other dopants. Acetone was excited by KrF excimer laser (248nm) and its fluorescence image was acquired by ICCD camera with a cut-of filter to suppress Mie scattering from the laser light. For the purpose of quantifying PLIF signal, an image processing method including the correction of laser sheet beam profile was suggested. Raw images were divided by each intensity of laser energy and profile of laser sheet beam. Inhomogeneous fluorescence images scaled with the reference data, which was taken by a calibration process, were converted to air excess ratio distribution. This investigation showed instantaneous quantitative measurement of planar air excess ratio distribution for gaseous fuel.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.3 no.1
• /
• pp.1-9
• /
• 1979

Methanol was examined as supplemental fuel for open chamber type and pre-combustion chamber type diesel engine. Pre-determined quantities of diesel oil were injected as ordinary diesel engines and methanol was added at inlet pipe using venturi, nozzel and and float chamber for the rest of the charge. In this mode of operation, addition of methanol reduced inlet and exhaust temperature. Inlet air quantities were essentially unchanged in spite of lower inlet temperature. Exhaust smoke was significantly reduced At light load when both diesel oil and methanol were introduced with small quantities, specific heat consumption was considerably increased. However, with the increase of the quantity of methanol or diesel oil, specific heat consumption was improved. With sufficient quantities of diesel oil enough to produce the power above 3/4 load, addition of methanol showed better thermal economy.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.1
• /
• pp.84-89
• /
• 2013

Titanium used in industry has been widely applied for aerospace engine, structures and spacecraft exterior, etc. because the titanium is higher in strength compared to the steel and light in weight compared to the steel. This study is to investigate the effect of cutting depth and cutting time on the spindle speed and feed rate of vertical machining center as a parameter to find the rough cutting time and cutting depth in the medium speed cutting machining of the titanium alloy. It is found that the cutting machining heat are increased as the cutting depth, feed rate, cutting time and spindle speed are raised.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.17 no.1
• /
• pp.29-38
• /
• 2009

This paper surveys the historical perspective and design considerations for developing the human powered aircraft(HPA). Especially the weight and materials, aerodynamics, flight controls, and power trains are focused. The average power a human can produce and sustain is approximately 200${\sim}$250 W which is a critical design constraint of HPA. The survey shows that the empty weight of HPA was in the 30${\sim}$40 kg range(90${\sim}$110 kg include pilot). Thus, in order to design a successful HPA, the value of power to weight ratio should be 2.0 W/kg or above. The HPA design technique could be applied directly to the development of an unmanned high altitude airplanes used for atmospheric research, where light structures, low Reynolds number aerodynamics and high efficiency propeller design are required as well.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.202-209
• /
• 2001

As a part of stringent emission regulations, OBD on a converter is requested by EU and CARB. It demands that MIL is light-on to inform the failure to the driver when the converter is failed in its function. Usually dual oxygen sensor method is used for converter OBD. For this, detail methods, like amplitude ratio, time delay and frequency ratio methods are adapted for vehicle application. Actually, the cars produced later than MY94 for US market are using one of these methods. In this study, OSCs of converters are investigated with an absolute measuring method. The converters are aged with a furnace aging, an engine bench aging and vehicle aging method to represent various aging condition in field applications. An OBD index that is used for TLEVs regulation is also investigated to find a relation between two parameters. The relations of these parameters with THC emission on vehicle are evaluated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.111-118
• /
• 2003

Recently, environmental damage to urban area becomes serious problem due to the exhaust emissions by increasing the number of vehicle. Especially, exhaust emission from diesel vehicles are blown to be harmful to human health and environment. Photoacoustic Spectroscopy system is very useful technology for simultaneous and continuous measurement of the various components of the automotive exhaust gas. In this study, in order to reduce emission gases from automobile, we tried to develop the measurement system of Photoacoustic Spectroscopy. To improve performance of high sensitive Photoacoustic Spectroscopy system for automotive exhaust emissions, the shape of Photoacoustic Spectroscopy cell was optimized to use the flow analysis. And Exhaust emission data of the 1,500cc gasoline engine was fixed the working fluid. The characteristics of fluid flow for cell were analyzed by various conditions in detail.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.5
• /
• pp.30-40
• /
• 1994

The direct-injection stratified-charge engine has the advantages of higher thermal efficiency and less CO and $NO_x$ emission levels than conventional spark ignition engines. However, its actual utilization is prevented by high unburned hydrocarbon emission levels during light-load operations. In this paper, fundamental studies were carried out using a pancake type constant volume bomb. The effects of intensification of local premixing by tangential and radial fuel injection were examined experimentally. Unburned hydrocarbon emission levels with radial fuel injection were shown to be lower than those of tangential fuel injection cases. The stratification and mixing process of fuel jet and combustion process were observed by schlieren photography.

• Publications of The Korean Astronomical Society
• /
• v.24 no.1
• /
• pp.83-91
• /
• 2009

We have designed data processing server system to include data archiving, photometric processing and light curve analysis for KMTNet (Korea Microlensing Telescope Network). Outputs of each process are reported to the main photometric database, which manages the whole processing steps and archives the photometric results. The database is developed using ORACLE 11g Release 2 engine. It allows to select objects applying any set of criteria such as RA/DEC coordinate and Star ID, etc. We tested the performance of the database using the OGLE photometric data. The searching time for querying 70,000,000 records was under 1 second. The database is fully accessed using query forms via web page.

• Journal of The Korean Astronomical Society
• /
• v.23 no.1
• /
• pp.63-70
• /
• 1990

The original axisymmetric, stationary electrodynamic model of the central engine in an active galactic nucleus proposed by Macdonald and Thorne consists of a supermassive black hole with magnetic field lines that pass through the region just outside the event horizon of the black hole. Each magnetic field line rotates with a constant angular velocity which will exceed the speed of light at large radii. Even though the field lines are purely mathematical entities this condition sets a stringent physical constraint on the motion of the magnetic field lines and the particles on them. In this paper we will show that we can remove this auxiliary constraint in our model by allowing nonstationary processes. As a result the magnetic field lines can be twisted and wound up in a region lying outside of the quasi-stationary magnetosphere of the black hole. We conclude that astrophysical jets are formed in that region due to the twisted and wound magnetic field lines powered by the Blandford-Znajek process and the other driving forces.

• Publications of The Korean Astronomical Society
• /
• v.26 no.1
• /
• pp.37-44
• /
• 2011

We constructed a photometric database system which is optimally designed for microlensing events from KMTNet (Korea Microlensing Telescope Network) observation. We developed a framework software for the convenience of archiving, uploading, searching, and downloading of processed photometric data. From various tests for optimal data archiving engines, we found that the MyISAM storage engine shows the best performance. For the high performance of database system, data types of each field are carefully suggested from various combinations of tests especially to correct round-off errors. The developed framework provides the convenience of access to the database server using query forms via web pages, and displays the light curve of selected target for a quick view.