• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.1
• /
• pp.82-95
• /
• 1992

There is the high interest for sensing of tool wear with the aim of controlling machine tools productivity from the point of view of qualitity. Difficulties in this measurement are also known. This study is on the development of measurement setup for crater wear by CCD image inturning. In this study, the crater wear measurement system consists of the He-Ne gas laser, diffraction grating. CCD camera, noise filter, slit, microcomputer, diverging lens, converging lens and so on. He-Ne laser beam passes through a diverging lens and a diffraction grating is positioned properly. A converging lens focuses so that the interference fringes can be obtained on the crater wear. Performance test revealed that the developed image technique provides precise, absolute tool-wear quantification and reduces human measurement errors. The results obtained are as follows 1. The digitizing of one image requires less than 2ses. 2. It can give detailed information on crater wear with limited times and errors 3. All parameters required by specification are easily obtained for several points of the cutting edge.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.89-92
• /
• 1998

Amorphous chalcogenide thin films, especially a-(Se, S) based films, exhibit a number of photoinduced phenomena not observed in other types of amorphous thin films. The polarization holographic grating has been formed in amorphous As-Ge-Se-S thin films using two linearly polarized He-Ne laser light. In addition, dffraction efficiency has been measured by the same laser of a relative lower intensity at the same time.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.107-107
• /
• 2010

In this study, we have investigated the holographic grating formation on Ag-doped amorphous chalcogenide AsGeSeS thin films with Ag thickness. Ag/AsGeSeS thin films with the incident laser beam wavelength for the improvement of the polarization diffraction grating efficiency. Holographic gratings have been formed using Diode Pumped Solid State laser (DPSS, 532.0nm) under [P:P] polarized the intensity polarization holography. The diffraction efficiency was obtained by +1st order intensity. The result is shown that the diffraction efficiency of Ag/AsGeSeS double layer thin film for the Ag thickness, the maximum grating diffraction efficiency using 60nm Ag layer is 0.96%.

• Korean Journal of Optics and Photonics
• /
• v.10 no.3
• /
• pp.233-236
• /
• 1999

We have constructed a narrow-linewidth single-longitudinal-mode unidirectional $Er^{3+}$ -doped fiber laser using a fiber Bragg grating incorporated by a three port optical circulator with a compact configuration. Using a conventional delayed self-heterodyne detection technique with Mach-Zehnder interferometer a linewidth of 5 kHz was measured. In a single-longitudinal-mode operation, output power of up to 2.7 mW at 1548 nm were obtained for a launched pump power of 43 mW at 980 nm.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.246-246
• /
• 2010

In this paper, we investigated the diffraction grating efficiency on AsSeS and Ag-doped amorphous chalcogenide Ag/AsSeS thin film for used to volume hologram. The Chalcogenide film thickness was 0.5um and Ag thin film was varied from 10nm and 20nm. Diffraction efficiency was obtained from (P:P) polarized Diode Pumped Solid State laser(DPSS, 532.0nm: 200mW) beam on AsSeS and Ag/AsSeS thin films. As a results, diffraction grating was not formed at AsSeS thin film but at Ag-doped AsSeS thin film, diffraction grating was formed well compare with the former.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.3
• /
• pp.463-468
• /
• 2021

In this paper, when a refractive index grating and a gain grating were simultaneously present in a DFB laser having a wavelength of 1.55 ㎛, a dielectric film coating was applied so that reflection did not occur on the right mirror surface, so that 𝜌_r=0. In case of 𝛿L>0, the characteristics of the oscillation frequency and oscillation gain were analyzed. When the grating phase of the left mirror surface continues to decrease from 𝜋, the graph lines of each mode gradually shift to the left. In case of 𝜅L=10, the threshold gain of the oscillation mode is the lowest. In this case, the mode selectivity is relatively low. From 𝜅L=0.5 to 𝜅L=6, the mode selectivity and the frequency stability are excellent. In the case of DFB lasers with an anti-reflection coated mirror, the threshold gain of the oscillation mode increases but the mode selectivity is about twice as excellent, compared with DFB lasers of having two cleaved facets.

• Journal of Software Assessment and Valuation
• /
• v.15 no.2
• /
• pp.101-109
• /
• 2019

Lasers for optical broadband communication systems should have excellent frequency selectivity and modal stability. DFB(Distributed Feedback) lasers have low lasing frequency shift during high speed current modulation. In this paper, I have developed a simulation software and analysed threshold gain and lasing frequency of a lasing mode in longitudinal direction of an 1.55um DFB laser with two mirrors and without anti-reflection coatings, that have both an index- and gain-gratings. The grating phase on a left mirror face is fixed as π/2 and the grating phase on a right mirror face is varied. As the phases of the index and gain gratings on the right mirror facet are π and 0, κL should be in the range of 2~6 in order to enhance the frequency stability. In order to reduce the threshold current of a lasing mode, κL should be greater than 8, regardless of the grating phases on the mirror faces.

• Korean Journal of Optics and Photonics
• /
• v.6 no.3
• /
• pp.222-227
• /
• 1995

A single mode, 100-mW diode laser was injection-locked by the master laser which was spectrally narrowed with Littman-type grating feedback. In the incomplete-injection-locking, we observed that two frequencies were simultaneously generated from the slave laser. The power ratio and frequency shift of two frequency components were proportional to the square of injected laser intensity. When the ratio of the injection intensity to the slave laser intensity was about $10^{-3}$, the injection-locking bandwidth was to be about 1.4 GHz. The bandwidth proportionally increased to the square root of the injection intensity, which was in good agreement with the theoretical predictions. The Iinewidth of the locked-laser was about 2.5 MHz, which was five times as narrow as that of free-running operation. ation.

• Korean Journal of Optics and Photonics
• /
• v.2 no.3
• /
• pp.153-157
• /
• 1991

We report an analysis on the stability properties of external cavity semiconductor lasers exposed to strong feedback from an external grating. The frequency range of stable single mode oscillation is found to depend on the offset between the resonance frequency of the solitary laser and the frequency of maximum reflection from the grating.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1257-1262
• /
• 2008

A long-distance remote sensing of temperature and current based on a fiber Bragg grating (FBG) is proposed and demonstrated. The thermal expanding effect of the epoxy and the Er-doped fiber ring laser (EFRL) are applied to the sensor system to enhance the temperature and current sensitivity. An EFRL with a 5 km-single-mode fiber and a FBG shows a high extinction ratio of more than 60 dB and a low power fluctuation of less than 1 dB. The metal wires are used to supply the current to the sensors. When the NOA65 puts on the FBG as a thermal expanding material, the temperature and current sensitivity of the lasing wavelength shift are about $30\;pm/^{\circ}C$ and 3pm/mA, respectively. The proposed sensing scheme is useful for measurement of current or temperature at a distant object of more than several km.