• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.1-15
• /
• 1997

Titanium oxide films were prepared by ion beam enhanced deposition where the films were synthesized by deposition titianium atoms and simultaneously bombarding with xenon ion beam at an energy of 40 keV in an $O_2$ environ,ent. Structure and composition of titanium oxide films were investigated by X-ray Doffractopm (XRD) Ritjerfprd Backscattering Spectroscopy (RBS) and X-ray Diffraction(XRD) Rutherford Backscattering Spectroscopy (RBS) and X-ray photoelectron spectroscopy (XPS) The results show that thestructure of the prepared films exhibit a rutile phase structure wit high(200) orientation and the O/Ti ratio of the titanium oxide films was about 2:1 XPS anlysis shows that $Ti^{2+},Ti^{3+}\;and\;Ti^{4+}$ chemical states exist on the titanium oxide films. the blood compatibility of the titanium oxide films was studied by measurements of blood clotting time and platelet adhesion. The results show that the anticoagulation property of titanium oxide films improved significantly and better than that of LTI-carbon which was widely used to fabricate artificial heart valve.

• Proceedings of the KIEE Conference
• /
• 2004.11d
• /
• pp.14-17
• /
• 2004

낙뢰는 본적으로 "완벽한 보호"가 불가능하며 단지 낙뢰 피해의 가능성을 최대한으로 낮추는데 그 의미가 있다. 기술 선진국의 경우 보호반경이나 보호범위는 이 범주 안에서 완벽한 보호가 됨을 명시하는 것이 아니며 어떤 보호확률을 설정하고 그 설정된 보호확률(보호효율)을 보장하는 범위가 어떻게 되는가를 나타내는 것이 보호범위(보호반경)이며 보호확률(보호효율)이 되는 개념인 것이다. 미국의 경우 NFPA에 의거하여, 보호개념의 뇌격거리를 30,45m로 명시하는 것이며 프랑스 및 유럽의 다수 국가에서는 NF C에 의거한 20,45,60m의 피격거리에 의한 보호반경(보호범위)를 명시한 것이다. 어느 것이 더 우수하고 나쁘고의 차원이 아니며 낙뢰보호의 설계시 건축물의 중요도, 낙뢰빈도수, 낙뢰전류의 크기 등 다양한 변수를 고려한 보호확률을 선정하여 보호범위를 설계하여야 할 것이다. 본 논문에서는 자체 개발된 ESE피뢰침을 통해 얻은 기술의 기본적 개념과 기술의 배경을 고찰하였으며 이를 통해 건축물의 적용시 보다 안정되고 효율 높은 낙뢰 보호를 위한 설계, 감리의 초석이 되고자 한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.9
• /
• pp.1710-1718
• /
• 1994

In this paper, a broadband tunable YIG(Yittrium Iron Garnet) oscillator is designed and fabricated. To design an YTO(YIG Tuned Oscillator), a suitable YIG resonator is selected according to the design oscillation range and its equivalent R, L, C resonant circuit parameters are obtained through the measurement of its resonance characteristic. Using the equivalent circuit, the wideband topology which suppresses the parasitic oscillation is selected and implemented. The designed circuit is simulated by HBT(Harmoic Balance Technique) using EEsof's jOMEGA. The YTO thus fabricated has the wide oscillation range from 1.4 GHz to 4 GHz, and its linearity is 0.5% in the oscillation range. The phase noise is below 105dBc at 100kHz offset.

• 제어로봇시스템학회:학술대회논문집
• /
• 1998.10a
• /
• pp.135-140
• /
• 1998

The concept of dissipativity and passivity are of interest to us from a theoretical as well as a practical point of view. It is well known that the Riccati equation is derived from the dissipation inequality which expresses the fact that the system is dissipative; the energy stored inside the system doesn't exceed the amount of supply which flows into the system. The pencil model is regarded as a representation based on behavioral approach introduced by J.C. Willems. It has first order in the internal variable and zeroth order in the external variable. In general, any matrix pencil is transformed into a canonical form which is consist of several kind of sub-pencils, One of them has row full rank for $^\forall S\;\in\;\mathds{C}\;\bigcup{\infty}$, we call it under-determined mode of the model. In our opinion, most important properties of dynamical system lay in the mode. According to the properties of canonical form for pencil, it is shown that the storage function which characterizes the dissipativity of the system can be written as a LMI for the under-determined mode, if the system doesn't include impulse mode.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.1
• /
• pp.20-23
• /
• 2006

This paper presents a new approach to the problem of designing a cascaded three-parameters controller for a given linear time invariant (LTI) plant in unity feedback system. We consider a proportional-integral-derivative (PID) and a first-order controller with the specified overshoot and settling time. This problem is difficult to solve because there may be no analytical solution due to the use of low-order controller. Furthermore, the zeros of controller just appear in the zeros of feedback system. The key idea of our method is to impose a constraint on the controller parameters so that the zeros of resulting controller are distant from the dominant pole of closed-loop system to the left as far as the given interval. Two methods realizing the idea are suggested. We have employed the characteristic ratio assignment (CRA) in order to deal with the time response specifications. It is noted that the proposed methods are accomplished only in parameter space. Several illustrative examples are given.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.685-688
• /
• 2003

In this paper, a performance comparison between two blind signal estimation algorithms in a LTI channel is considered. The two algorithms, Iterative Least-Squares with Projection (ILSP) and a modified ILSP, are based on the finite-alphabet property of input symbols. This case typically arises in a multiple access system with a sensor array antenna at the receiving end. We start with the formulation of a maximum-likelihood (ML) estimation problem under an additive white Gaussian noise assumption. A blind ML estimator is derived with its iterative algorithm for calculation. Then we narrow down the consideration of this problem to QPSK case so that a modified algorithm is proposed for $\pi$/4-QPSK case. The modified version is compared with the original ILSP algorithm in terms of the rate of the convergence to global minima. A computer simulation shows that the modified algorithm gives a better performance. This result implies that the performance of the blind separation algorithms may be greatly improved by adopting a smart coding scheme with rich structure.

• Steel and Composite Structures
• /
• v.26 no.2
• /
• pp.227-239
• /
• 2018

Integral abutment bridges (IABs) have no joint across the length of bridge and are therefore also known as jointless bridges. IABs have many advantages, such as structural integrity, efficiency, and stability. More importantly, IABs have proven to be have both low maintenance and construction costs. However, due to the restraints at both ends of the girder due to the absence of a gap (joint), special design considerations are required. For example, while replacing the deck slabs to extend the service life of the IAB, the buckling strength of the steel girder without a deck slab could be much smaller than the case with deck slab in place. With no deck slab, the addition of thermal expansion in the steel girders generates passive earth pressure from the abutment and if the applied axial force is greater than the buckling strength of the steel girders, buckling failure can occur. In this study, numerical simulations were performed to estimate the buckling strength of typical steel girders in IABs. The effects of girder length, the width of flange and thickness of flange, imperfection due to fabrication and construction errors on the buckling strengths of multiple and single girders in IABs are studied. The effect of girder spacing, span length ratio (for a three span girder) and self-weight effects on the buckling strength are also studied. For estimation of the reaction force of the abutment generated by the passive earth pressure of the soil, BA 42/96 (2003), PennDOT DM4 (2015) and the LTI proposed equations (2009) were used and the results obtained are compared with the buckling strength of the steel girders. Using the selected design equations and the results obtained from the numerical analysis, equations for preventing the buckling failure of steel girders during deck replacement for maintenance are presented.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.1
• /
• pp.1-6
• /
• 2015

This paper investigates the longitudinal flight dynamics and stability of flapping-wing micro air vehicles. Periodic external forces and moments due to the flapping motion characterize the dynamics of this system as NLTP (Non Linear Time Periodic). However, the averaging theorem can be applied to an NLTP system to obtain an NLTI (Non Linear Time Invariant) system which allows us to use a standard eigen value analysis to assess the stability of the system with linearization around a reference point. In this paper, we investigate the dynamics and stability of a hawkmoth-scale flapping-wing air vehicle by establishing an LTI (Linear Time Invariant) system model around a hovering condition. Also, a direct time integration of full nonlinear equations of motion of the flapping-wing micro air vehicle is conducted to see how the longitudinal flight dynamics appear in the time domain beyond the reference point, i.e. hovering condition. In the study, the flapping-wing air vehicle exhibited three distinct dynamic modes of motion in the longitudinal plane of motion: two stable subsidence modes and one unstable oscillatory mode. The unstable oscillatory mode is found to be a combination of a pitching velocity state and a forward/backward velocity state.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.17 no.3
• /
• pp.285-290
• /
• 2007

In this paper, we presents robust digital redesign (DR) method for observer-based linear time-invariant (LTI) system. The term of DR involves converting an analog controller into an equivalent digital one by considering two condition: state-matching and stability. The design problems viewed as a convex optimization problem that we minimize the error of the norm bounds between interpolated linear operators to be matched. Also, by using the bilinear and inverse bilinear approximation method, we analyzed the uncertain parts of given observer-based system more precisely, When a sampling period is sufficiently small, the conversion of a analog structured uncertain system to an equivalent discrete-time system have proper reason. Sufficiently conditions for the state-matching of the digitally controlled system are formulated in terms of linear matrix inequalities (LMIs).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.6
• /
• pp.515-518
• /
• 2011

In this work, we designed and fabricated a multilayer thin film Pb(Zr,Ti)$O_3$ cantilever with a Si proof mass for low frequency vibration energy harvesting applications. A mathematical model of a mu lti-layer composite beam was derived and applied in a parametric analysis of the piezoelectric cantilever. Finally, the dimensions of the cantilever were determined for the resonant frequency of the cantilever. W e fabricated a device with beam dimensions of about 4,930 ${\mu}M$ ${\times}$ 450 ${\mu}M$ ${\times}$ 12 ${\mu}M$, and an integrated Si proof mass with dimensions of about 1,410 ${\mu}M$ ${\times}$ 450 ${\mu}M$ ${\times}$ 450 ${\mu}M$. The resonant frequency, maximum peak voltage, and highest average power of the cantilever device were 84.5 Hz, 88 mV, and 0.166 ${\mu}Wat$ 1.0 g and 23.7 ${\Omega}$, respectively. The dimensions of the cantilever were determined for the resonance frequency of the cantilever.