• 한국가스학회지
• /
• 제3권2호
• /
• pp.43-52
• /
• 1999

지하에 매설된 도시가스 배관에서의 누출 가스에 대한 확산 거동을 관찰하기 위하여 지중 확산실험조를 제작하여 실험하였다. 실험조는 도시가스 공급위치와 농도의 측정위치를 변화시킬 수 있도록 acryl로 제작하였으며, MOS 센서를 이용하여 도시가스 농도를 측정하였다. 가스의 지하 확산을 측정하기 위한 토질로서 주문진 표준사와 화강풍화토를 이용하였으며, 가스누출 속도 변화에 따른 도시가스 농도 변화를 시간에 따라 측정하였다. 누출점으로부터 센서의 측정위치가 가까울수록 또는 누출 속도가 증가할수록 가스의 감지시간이 감소하였으며, 누출가스 농도의 빠른 증가로 인하여 정상상태시 높은 농도를 나타내었다. 또한, 주문진 표준사보다 다짐에 의해 밀도가 증가한 화강풍화토에서 초기에 농도가 낮게 측정되었으나, 시간이 지남에 따라 농도가 높게 나타났다.

• 산업기술연구
• /
• 제24권A호
• /
• pp.227-238
• /
• 2004

This paper is results of experimental and nunerical works on the behavior of the cut-and-cover tunnel. Centrifuge model tests were performed to simulate the behavior of the cut-and-cover tunnels having cross sections of national road and subway tunnels. Model experiments were carried out with changing the cut slope and the slope of filling ground surface. Displacements of tunnel lining resulted from artificially accelerated gravitational force up to 40g of covered material used in model tests, were measured during centrifuge model tests. In model tests, Jumunjin Standard Sand with the relative density of 80 % and the zinc plates were used for the covered material and the flexible tunnel lining, respectively. Basic soil property tests were performed to obtain it's the property of Jumumjin Standard Sand. Shear strength parameters of Jumunjin Standard Sand were obtained by performing the triaxial compression tests. Direct shear tests were also carried out to find the mechanical properties of the interface between the lining and the covered material. Numerical analysis with the commercially available program of FLAC were performed to compare with results of centrifuge model experiment In numerical modelling. Mohr-Coulomb elasto-plastic constitutive model was used to simulaye the behavoor of Jumunjin Standard Sand and the interface element between the lining and the covered material was implemented to simulate the interaction between them. Compared results between model tests and numerical estimation with respect to displacement of the lining showed in good agreements.

• 산업기술연구
• /
• 제24권B호
• /
• pp.107-116
• /
• 2004

This thesis is results of experimental works on the behavior of the cut-and-cover tunnel. Centrifuge model tests were performed to simulate the behavior of the cut-and-cover tunnels having cross sections of national road and subway tunnels. Model experiments were carried out with changing the cut slope and the slope of filling ground surface. Displacements of tunnel lining resulted from artificially accelerated gravitational force up to 40g of covered material used in model tests, were measured during centrifuge model tests. In model tests, Jumunjin Standard Sand with the relative density of 80 % and the zinc plates were used for the covered material and the flexible tunnel lining, respectively. Basic soil property tests were performed to obtain it's the property of Jumumjin Standard Sand. Shear strength parameters of Jumunjin Standard Sand were obtained by performing the triaxial compression tests. Direct shear tests were also carried out to find the mechanical properties of the interface between the lining and the covered material. Compared results model tests estimation with respect to displacements of the lining.

• 산업기술연구
• /
• 제23권A호
• /
• pp.119-130
• /
• 2003

This thesis is results of experimental works on the behavior of the cut-and-cover tunnel. Centrifuge model tests were performed to simulate the behavior of the cut-and-cover tunnels having cross sections of national road and subway tunnels. Model experiments were carried out with changing the cut slope and the slope of filling ground surface. Displacements of tunnel lining resulted from artificially accelerated gravitational force up to 40g of covered material used in model tests, were measured during centrifuge model tests. In model tests, Jumunjin Standard Sand with the relative density of 80 % and the zinc plates were used for the covered material and the flexible tunnel lining, respectively. Basic soil property tests were performed to obtain it's the property of Jumumjin Standard Sand Shear strength parameters of Jumunjin Standard Sand were obtained by performing the triaxial compression tests. Direct shear tests were also carried out to find the mechanical properties of the interface between the lining and the covered material. Compared results model tests estimation with respect to displacements of the lining.

• 한국농공학회지
• /
• 제33권3호
• /
• pp.51-62
• /
• 1991

A comprehensive laboratory investigation of the liquefaction characteristics of Jumunjin standard sand. Seoul sand and Hongsung sand was peformed by the undrained cyclic triaxial compression test under different relative densities, confining pressures and cyclic deviator stresses. The results obtained are as follows ; 1. Liquefaction potential was dominated by the stress ratio at a given number of cycle. That is, the number of cycle required to cause initial liquefaction became samller as the stress ratio increased. 2. Liquefaction potential of a sand was infliuenced by initial relative density or void ratio. Under a given relative density. liquefaction potential of Jumunjin standard sand and Seoul sand was smaller than that of Hongsung sand. 3. The pore pressure ratio of Hongsung sand was the smallest three under a given relative density and stress ratio, and it showed higher value when the cyclic stress and the shear strain were high. 4. An excessive pore pressure ratio not found when initial shear was smaller than 0.01%, and the pore pressure ratio started to increase when initial shear became greater than 0.01%. 5. Soil texture is an important factor to cause liquefaction, and liquefaction potential decreased a the mean grain size decreased. however the sand having fine grain such as Hongsung sand showed somewhat higher liquefaction potential. 6. Based on the analysis of the specimens whose number of the cycles to cause liquefaction was 8~12, it was found that the relationship between density and stress ratio was linear. The curves for Hongsung sand was steeper than the other. 7. From the above results and the method suggested by Seed-Idriss, it may be considered that the damages by Hongsung earthquake was not directly caused by liquefaction.

• 산업기술연구
• /
• 제24권A호
• /
• pp.251-261
• /
• 2004

A series of column test with a silty marine soil mixed with Jumunjin Standard Sand were performed to investigate the characteristics of settling and consolidation of non-plastic dredged soils. Column tests were carried out by using the separable column to measure the grain size distribution of consolidated layer. Column tests were performed with changing the mixing ratio of Jumunjin Standard Sand to the silty marine soil, initial water content of slurry and initial height of slurry. Height of interface of slurry was monitored during tests and grain size distribution tests were carried out after finishing tests. Influencing factors on the particle segregation, eventually to the characteristics of settling and consolidation of non-plastic soil, were analyzed on the thesis of test results. As results of column tests, the mixing ratio of sand to the silty marine soil and the initial water content of slurry were known to affect the characteristics of settling and consolidation resulted in significant particle segregation of slurry. Initial height of slurry was found not to affect seriously to particle segregation.

• 산업기술연구
• /
• 제25권A호
• /
• pp.67-73
• /
• 2005

In this research, centrifuge model experiments and numerical approach of finite element method to analyze experimental results were performed to investigate the behavior of improved ground with sand compaction piles. One of typical clay minerals, kaolinite powder, were prepared for soft ground in model tests. Jumunjin standard sand was used to sand compaction pile installed in the soft soil. In order to investigate the characteristics of mechanical behavior of sand compaction piles with low replacement ratios, centrifuge model experiments with the replacement ratio of 40%, changing the width of improved area with respect to testing results the width of surcharge loads, were carried out to obtain of bearing capacity, characteristics of load-settlement, vertical stresses acting on the sand pile and the soft soil failure mechanism in improved ground.

• 지구물리와물리탐사
• /
• 제16권2호
• /
• pp.79-90
• /
• 2013

지반조사에서 비파괴 조사 기술은 시추조사보다 경제적으로 비용이 덜 들고 광역에 걸친 지반정보를 제공하는 장점이 있다. 하지만 지반설계정수로서 적용하기에는 어려운 한정된 정보만을 제공하게 된다. 이를 극복하기 위해, 비파괴 조사 방법 중 하나인 전기비저항 탐사를 모형토조실험에 적용하여, 토질상태에 따른 비저항 반응과 함수비에 따른 비저항 반응을 분석하여 비저항 거동 양상에 대한 연구를 수행하였다. 실험에 사용한 토질은 주문진 표준사, 마사토이며 각 토질의 입도 분포, 균등계수를 구하여 실험에 있어 실험재료의 균질한 상태를 유지하였다. 실험에 사용한 모형의 제원은 $160{\times}100{\times}50$ (cm)의 아크릴 재질 토조이며, 각 토질의 높이는 30 cm를 유지하였다. 5TE(함수비측정센서)센서를 7 ~ 8cm 간격으로 수직하게 꽂아 층별 함수비를 측정하였다. 모형실험 결과 주문진 표준사는 비저항 거동 양상이 함수비에 민감하게 반응하는 것을 알 수 있었으며, 마사토는 함수비에 따라 비저항이 낮아진 후에도 시간경과에 따른 거동 양상에 큰 변화가 없는 것을 관찰하였다. 또한 토조 실험에 사용된 토양과 유사한 테스트 베드를 선정하여 그 반응을 비교 분석하였다. 이러한 실험을 통해 토질 상태와 함수비에 따른 다양한 비저항 거동 양상 자료를 수집하고, 비파괴 조사기술의 정확도를 향상 시켜 나간다면 지반설계정수를 산정하는데 있어 기초적인 연구가 될 수 있음을 확인하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1994년도 가을 학술발표회 논문집
• /
• pp.265-272
• /
• 1994

The relative density seems to be important as a factor of controlling the physical properties in the case of cohesionless soil ground as sand. Therefore, the study is more important about the method for reappearing the same relative density when the specimen of shearing test is to be produced or the model test of ground is to be made. In this study, the apparatus making use of the multiple sieving pluviation method - one of the reappearance of relative density - could be made. Using this apparatus, tests were practiced varying the factors such as the size of sieve mesh and the number of sieve, the amount of falling discharge, the falling height etc. about the standard sand in Jumunjin and Hadong sand. When laboratory test is performed by the cohensionless soil , it presents the method for reappearing of the relative density in field.

• 한국지반공학회논문집
• /
• 제15권4호
• /
• pp.207-220
• /
• 1999

성토지지말뚝으로 지지된 연약지반상 성토지반의 파괴형태를 조사하기 위하여 실내모형실험이 실시되었다. 성토지지말뚝은 성토하중의 지지효과를 증대시키기 위하여 줄말뚝의 형태로 설치하였으며 줄말뚝의 두부는 지중보 형태의 말뚝캡보로 서로 연결시켰다. 이 말뚝캡보는 성토지반의 장축방향에 직각이 되도록 연결시켰다. 사용모래로는 주문진 표준사를 사용하였으며 성토지반의 변형거동을 관찰하기 위하여 흑연가루로 채색한 모래층과 원래의 모래층을 서로 3mm두께로 번갈아 성토하여 줄무늬를 만들었다. 실험중 촬영한 사진분석으로 부터 성토지반의 파괴형태는 지반아칭파괴와 펀칭전단파괴의 두가지임을 알 수 있다. 성토지반내 어떤 파괴형태가 발생될 것인가는 성토고와 말뚝캡보 사이의 간격에 의존함을 알 수 있다. 즉 성토고가 말뚝캡보사이 간격에 비하여 충분히 높으면 지반아칭파괴가 발생되며 그 반대의 경우는 펀칭전단파괴가 발생된다. 지반아칭파괴는 말뚝캡보 폭과 같은 두께를 가지는 반원통형 아치형태로 성토지반내에 발생한다. 그리고, 말뚝캡보 위에는 쐐기영역이 발생하며 이 쐐기영역은 지반아칭파괴나 펀칭전단파괴가 발달하는 동안에도 변형되지 않은 상태로 남아있다. 펀칭전단파괴시 변형토괴의 경계형상도 실험중 촬영한 사진분석에 근거하여 밝혀질 수 있다.