• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.445-448
• /
• 2006

Bias stress effect in pentacene organic thin-flim transistors with cross-linked PVA gate dielectric is analyzed. For negative gate bias stress, positive threshold voltage shift is observed. The injected charges from the gate electrode to the defect states of gate dielectric are regarded as the main origin of $V_T$ shift. The reduced bias stress effect using $SiO_2$ blocking layer confirms the assumed mechanism. It is also demonstrated that the inverter with $SiO_2$ blocking layer shows the negligible hysteresis owing to the reduced bias stress effect.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.4
• /
• pp.131-134
• /
• 2011

Back-end-of-line using ultra low-k (ULK; k < 2.5) has been required to reduce resistive capacitance beyond 45 nmtechnologies, because micro-processing units need higher speed and density. There are two strategies to manufacture ULK inter-layer dielectric (ILD) materials using an air-gap (k = 1). The former ULK and calcinations of ILD degrade the mechanical strength and induce a high cost due to the complication of following process, such as chemical mechanical polishing and deposition of the barrier metal. In contrast, the air-gap based low-k ILD with a relatively higher density has been researched on the trench-type with activity, but it has limited application to high density devices due to its high air-gap into the next metal layer. The height of air-gap into the next metal layer was reduced by changing to the via-typed air-gap, up to about 50% compared to that of the trench-typed air-gap. The controllable ULK was easily fabricated using the via-typed air-gap. It is thought that the via-type air-gap made the better design margin like via-patterning in the area with the dense and narrow lines.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.15-18
• /
• 2003

Pentacene OTFTs of $Al_2O_3$ insulator treated with a diluted PMMA were fabricated for the application of the low voltage operation and large area displays. The operation voltage of 15 V and the mobility of 0.35 $cm^2/Vsec$ are obtained even adopting the thick dielectric of 100 nm which was deposited by atomic layer deposition at the temperature of $150^{\circ}C$. The current on-off ratio was $4.1{\times}10^4$ for the OTFTs treated with 9:1 PMMA and good saturation characteristics were obtained as drain voltage increases.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.134-136
• /
• 2002

유리기판 위에서 제작된 다결정 실리콘 TFT(Thin Film Transistor) 에서는 열전도율이 낮은 실리콘 산화막 같은 물질이 사용되기 때문에 열에 대해서 낮은 임계점을 갖는다. 이로 인하여. 게이트와 드레인에 높은 전압이 걸리는 조건에서 동작시킬 경우에는 다결정 실리콘 TFT에서의 열화 현상이 두드러지게 나타나게 된다. 그러나, 열전도율이 실리콘 산화막(SiO2) 보다 열배 이상 높은 실리콘 질화막(SiNx)을 ILD(inter-layer dielectric) 재료로 사용했을 때 같은 스트레스 조건에서 다결정 실리콘의 신뢰성이 개선되는 것을 확인할 수 있었다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.614-615
• /
• 2016

I studied electrical coupling of monolithic 3D inverter(M3D-INV) consisting of Junctionless FET(JLFET). If the thickness of Inter Layer Dielectric (ILD) between top JLFET and bottom JLFET is less than 50nm, current-voltage characteristic of top JLFET is rapidly changed by the gate voltage of bottom JLFET. Therefore, you have to consider about the electrical interaction according to the thickness between top JLFET and bottom JLFET in M3D-INV.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.81-81
• /
• 2007

Chemical mechanical polishing (CMP) 공정은 deep 서브마이크론 집적회로의 다층배선구조률 실현하기 위해 inter-metal dielectric (IMD), inter-layer dielectric layers (ILD), pre-metal dielectric (PMD) 층과 같은 절연막 외에도 W, Al, Cu와 같은 금속층을 평탄화 하는데 효과적으로 사용되고 있으며, 다양한 소자 제작 및 새로운 물질 등에도 광범위하게 응용되고 있다. 하지만 Cu damascene 구조 제작으로 인한 CMP 응용 과정에서, 기계적으로 깨지기 쉬운 65 nm의 소자 이하의 구조에서 새로운 저유전상수인 low-k 물질의 도입으로 인해 낮은 하력의 기계적 연마가 필요하게 되었다. 본 논문에서는 전기화학적 기계적 연마 적용을 위해, I-V 특성 곡선을 이용하여 active, passive, transient, trans-passive 영역의 전기화학적 특성을 알아보았으며, Cu 막의 표면 형상을 알아보기 위해 scanning electron microscopy (SEM) 측정과 energy dispersive spectroscopy (EDS) 분석을 통해 금속 화학적 조성을 조사하였다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.10
• /
• pp.9-16
• /
• 1999

When the conventional IPD (inter-poly-dielctrics) layer with ONO(oxide-nitride-oxide) structure was used in the Flash EEPROM cell, its data retention characteristics were significanfly degraded because the top oxide of the ONO layer was etched off due to the cleaning process used in the gate oxidation process for the peripheral MOSFETs. When the IPD layer with the ONON(oxide-nitride-oxide-nitride) was used there, however, its data retention characteristics were much improved because the top nitride of the ONON layer protected the top oxide from being etched in the cleaning process. For the modelling of the data retention characteristics of the Flash EEPROM cell with the ONON IPD layer, the decrease of the threshold voltage cue to the charge loss during the bake was here given by the empirical relation ${\Delta}V_t\; = \;{\beta}t^me^{-ea/kT}$ and the values of the ${\beta}$=184.7, m=0.224, Ea=0.31 eV were obtained with the experimental measurements. The activation energy of 0.31eV implies that the decrease of the threshold voltage by the back was dur to the movement of the trapped electrons inside the inter-oxide nitride layer. On the other hand, the results of the computer simulation using the model were found to be well consistent with the results of the electrical measurements when the thermal budget of the bake was not high. However, the latter was larger then the former in the case of the high thermal budger, This seems to be due to the leakage current generated by the extraction of the electrons with the bake which were injected into the inter-oxide niride later and were trapped there during the programming, and played the role to prevent the leakage current. To prevent the generation of the leakage current, it is required that the inter-oxide nitride layer and the top oxide layer be made as thin and as thick as possible, respectively.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.5
• /
• pp.191-195
• /
• 2002

Chemical mechanical Polishing (CMP) process is widely used for the global planarization of inter-metal dielectric (IMD) layer and inter-layer dielectric (ILD) for deep sub-micron technology. However, as the IMD and ILD layer gets thinner, defects such as micro-scratch lead to severe circuit failure, which affect yield. In this paper, for the improvement of CMP process, deionized water (DIW) pressure, purified $N_2$ ($PN_2$) gas, point of use (POU) slurry filler and high spray bar (HSB) were installed. Our experimental results show that DW pressure and P$N_2$ gas factors were not related with removal rate, but edge hot-spot of patterned wafer had a serious relation. Also, the filter installation in CMP polisher could reduce defects after CMP process, it is shown that slurry filter plays an important role in determining consumable pad lifetime. The filter lifetime is dominated by the defects. However, the slurry filter is impossible to prevent defect-causing particles perfectly. Thus, we suggest that it is necessary to install the high spray bar of de-ionized water (DIW) with high pressure, to overcome the weak-point of slurry filter Finally, we could expect the improvements of throughput, yield and stability in the ULSI fabrication process.

• Macromolecular Research
• /
• v.15 no.2
• /
• pp.114-128
• /
• 2007

Polyimides are one of the most important classes of polymers used in the microelectronics and photoelectronics industries. Because of their high thermal stability, chemical resistance, and good mechanical and electric properties, polyimides are often applied in photoresists, passivation and dielectric films, soft print circuit boards, and alignment films within displays. Recently, fully aliphatic and alicyclic polyimides have found applications as optoelectronics and inter layer dielectric materials, due to their good transparencies and low dielectric constants $(\varepsilon)$. The low molecular density, polarity and rare probability of forming inter- or intra-molecular charge transfers, resulting in lowering of the dielectric constant and high transparency, are the most striking characteristics of aliphatic polyimide. However, the ultimate end use of polyimides derived from aliphatic monomers is in their targeted applications that need less stringent thermal requirements. Much research effort has been exerted in the development of aliphatic polyimide with increased thermal and mechanical stabilities, while maintaining their transparencies and low dielectric constants, by the incorporation of rigid moieties. In this article, the recent research process in synthesizing fully aliphatic polyimides, with improved dimensional stability, high transparency and low $\delta$values, as well as the characterizations and future scope for their application in micro electric and photo-electronic industries, is reviewed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.34-37
• /
• 2001

As the integrated circuit device shrinks to smaller dimensions, chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric (IMD) layer with free-defect. However, as the inter-metal dielectrics (IMD) layer gets thinner, micro-scratches are becoming as major defects. Micro-scratches are generated by agglomerated slurry, solidified and attached slurry in pipe line of slurry supply system. To prevent agglomerated slurry particle from inflow, we installed 0.5${\mu}m$ POU (point of use) filter, which is depth-type filter and has 80% filtering efficiency for the $1.0{\mu}m$ size particle. In this paper, we studied the relationship between defect generation and pad count to understand the exact efficiency of the slurry filtration, and to find out the appropriate pad usage. Our preliminary results showed that it is impossible to prevent defect-causing particles perfectly through the depth-type filter. Thus, we suggest that it is necessary to optimize the flow rate of slurry to overcome depth type filters weak-point, and to install the high spray of de-ionized Water (DIW) with high pressure.