• Journal of Digital Contents Society
• /
• v.16 no.3
• /
• pp.463-470
• /
• 2015

The angular dependence of active dosimeters, EPD, is analysed and compared with that of passive dosimeters, OSLD, after evaluating their relative response and uncertainty of measurement, where it is known that the personal use of them has been increased recently. There appeared a minor variation for average relative response of OSLD in the horizontal and vertical directions within the range $0^{\circ}{\sim}{\pm}90^{\circ}$, which are 0.97 and 0.95 respectively. The variations of angular dependence in the same situations with OSLD are 0.65 and 0.62, respectively, which also reveals a negligible effect on the overall uncertainty. EPDs within the interval $0^{\circ}{\sim}{\pm}60^{\circ}$ for horizontal and vertical directions are 0.94 and 0.97, respectively. These satisfy the requirements of IEC 61526. Uncertainties about the dependence of direction from horizontal and vertical directions are 0.44, 0.40, respectively. The impact of these uncertainties on the overall uncertainty was negligible. However, we observed a significant change in reactivity: the relative reactivities for $+90^{\circ}$ and $-90^{\circ}$ from the horizontal direction are 0.60, 0.37, while that form vertical direction is 0.06. The direction dependence of OSLD was superior to EPD in the range of $0^{\circ}{\sim}{\pm}90^{\circ}$. There appeared a rapidly changing structural features in EPD response for a certain direction. Therefore, we conclude that concurrent use of passive dosimeters and auxiliary dosimeter provides accurate data for personal dose measurements.

• The Journal of the Korea Contents Association
• /
• v.15 no.10
• /
• pp.362-373
• /
• 2015

This study analysed the effectiveness of aluminium(Al) filter in the added compound filtration for the removal of characteristic radiation from high atomic number material by DQE and image evaluation. 1mm Al was applied to each 0.1, 0.2, 0.3 mm copper and befere and after use were evaluated. Beam quality and DQE were tested by IEC regulations and image quality was evaluated by PSNR, MAE, MSE, CNR, SNR and qualitative analysis was performed by 7 items for resolution and contrast from chest x-ray criteria of national cancer checkup. MTF 10 and 50% were the same by 4.6, 2.54 cycle/mm and NPS, DQE, PSNR MAE, MSE, CNR, SNR and qualitative analysis were all the same or slightly better when Al was not used. PSNR is over 30dB and all significant and at the qualitative analysis, the p-value of t-test was over 0.05. The DQE and image quality evaluation have little difference between before and after use of Al filter and it is effective to use the Al filter for the reduction of skin dose by removal of characteristic radiation.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.3 no.2 s.5
• /
• pp.119-128
• /
• 2004

Recently, the accidents on the sea have arisen due to the increase of the nautical traffic and the digitization of equipments for marine. Therefore, IMO(International Maritime Organization) have provided the recommendation of EMI and EMS for radio communication and equipments of marine from SOLAS convention at July 1st 2002. In this paper, we measured EMC environment on the Hanbada, which is Korea Maritime University training ship, for basic EMC environment of ship. The measuring point was Bridge and Engine Control Room of the ship, we measured at the test point that was set at random. Measured Band is from 30 MHz to 2 GHz, polarization measurement is processed both vertical and horizontal polarization. We analysed the results in consideration of permissible criteria.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.133-143
• /
• 2001

This paper describes the correlation of the transient impedance and its parameters with the stationary resistance of a grounding system to a square pulse current and a lightning impulse current. In the experiment, the grounding system consists of a single grounding rod$(\Psi10[mm], 1[m])$and/or a triple-grounding rods of equilateral triangles with 5[m] spacing for operation. To analyze the transient impedance characteristics of the grounding system, a pulse generator which can produce square wave of a 30[ns] rise-time and a $20[\mus] $pulse duration is designed and fabricated. The injected content in the grounding system and the developed potential were recorded, and the time variation of the transient impedance were calculated as the ratio of the potential rising to the injected current at each time. The transient impedance and the effective surge impedance Z3 which defines economic protection level in power system were quite higher than the stationary resistance. The grounding impedance is decreased by the application of the triple-rods grounding system, and its effect is decreased as the frequency of the current is increased due to the inductance of the grounding leads.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.29 no.1
• /
• pp.141-146
• /
• 2005

Recently, the accidents on the sea have arisen due to the increase of the nautical traffic and the digitization of equipments for marine. Therefore, IMO(International Maritime Organization) have provided the recommendation of EMI and EMS for radio communication and equipments of marine from SOLAS cobvention at July 1st 2002. In this paper, we measured EMC environment on the HANBADA, which is Korea Maritime University training ship, for basic EMC environment of a ship. The measuring point was Bridge and Engine Control Room of the ship, we measured the test point that was set at random. Measured Band is from 30 MHz to 2 GHz, polarization measurement is processed both vertical and horizontal polarizaion. We analysed the results in consideration of permissible criteria.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.248-253
• /
• 2020

This paper proposed PTP(Precision Time Protocol) management node-based time synchronization error detection and recovery system. The proposed system is to maintain the preciseness of time synchronization under time synchronization error situations on IEEE 1588-based network environment. To demonstrate the proposed time synchronization error detection and recovery system, PTP implemented EVM(Evaluation Module)-based experiments were performed. As a results of the experiments, it is shown that the proposed system effectively maintains the preciseness of time synchronization under time synchronization error situations.

• Journal of Digital Convergence
• /
• v.19 no.10
• /
• pp.75-86
• /
• 2021

Recently, the domestic BIPV market is expected to revitalize with the introduction of the "zero-energy building certification system(2020~)", but it is somewhat stagnant due to the rigidity of definitions in the current domestic BIPV construction standards. Also, since there is delaying revision on definition and standardization of BIPV, the system is so weak that there are cases where it has been approved as BIPV simply by installing a structure on the wall and fixing the module roughly. The damage caused by this can be passed on to consumers, and it can only create a negative perception of BIPV and jeopardize the entire market. The BIPV definition was prepared through a Delphi survey of related experts about market stagnant cause, unreasonable regulation, etc, and a revised plan was derived accordingly.

• Journal of Broadcast Engineering
• /
• v.13 no.2
• /
• pp.200-213
• /
• 2008

H.264| MPEG-4 AVC is a new video codingstandard defined by JVT (Joint Video Team) which consists of ITU-T and ISO/IEC. Many techniques are adopted fur the compression efficiency: Especially, an intra prediction in an inter frame is one example but it leads to excessive amount of encoding time due to the decision of a candidate mode and a RDcost calculation. For this reason, a fast determination of the best intra prediction mode is the main issue for saving the encoding time. In this paper, by using the result of statistical relation between intra $16{\times}16$ and $4{\times}4$ intra predictions, the number of candidate modes for $4{\times}4$ intra prediction is reduced. Firstly, utilizing motion vector obtained after inter prediction, prediction of a block mode for each macroblock is made. If an intra prediction is needed, the correlation table between $16{\times}16$ and $4{\times}4$ intra predicted modes is created using the probability during each I frame-coding process. Secondly, using this result, the candidate modes for a $4{\times}4$ intra prediction that reaches a predefined specific probability value are only considered in the same GOP For the experiments, JM11.0, the reference software of H.264|MPEG-4 AVC is used and the experimental results show that the encoding time could be reduced by 51.24% in maximum with negligible amounts of PSNR drop and bitrate increase.

• Progress in Medical Physics
• /
• v.20 no.4
• /
• pp.253-259
• /
• 2009

We have developed standards based on international criterions for the quality control of dose tested by the measurement institutions of individual exposure doses through improving the reliability of data on the exposure dose of individuals working in radioactive environment and securing the accuracy and reliability of individual dose measurements. Laws related to radiation dose applied to domestic institutions refer to ANSI N13.11.1993, but currently, in U.S. and some other countries the measurement of radiation doses is based on ANSI N13.11.2001 that reduced test categories and tightened the standards. We made efforts to simplify the standards and to reduce the number of dosimeters required in experiment, and avoided preventing or hindering the use of future technologies not approved under the current law such as glass dosimeter and optical stimulation dosimeter. The Quality Management Manual of Radiation Dosimetry Service, Assessment Manual of Radiation Dosimetry Service Accreditation Program, and the Personnel Dosimetry Performance. Criteria for Testing are documents applicable in supervising laboratories.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.5 no.4
• /
• pp.83-93
• /
• 1994

1886년 고트리브 다이믈러와 칼 벤즈가 가솔린 자동차를 개발한 이후 100여년이 지난 지금 자동차는 비약적으로 진보, 발전하여 현대 산업사회와 개인의 생활에 있어 산업운송수단과 이동수단으 로서 필요불가결하게 되어 밀접한 관계를 갖고 있다. 우리나라 자동차 공업의 역사는 자동차가 사회적, 경제적 효용에 따라 그 생산과 보유대수가 날이 갈수록 증가 일로에 있으며, 자동차의 생산대수는 전세 계에서 년간 약 50,606천대('94년)로서 중요한 국가 기간 산업으로 자리하고 있다. 한편 전기, 전자공업의 발전에 따른 자동차의 Car Electronics가 많이 채용되게 됨에 따라 현재의 자 동차에는 대부분이 전자제어 System으로 구성되어 있다. 최근에는 Micro Processor를 이용한 전자부품이 많이 사용되어 전자파에 대한 문제가 다양하게 발생 하고 있다. 예를 들면 미국 캘리포니아주에서 전자점화제어장치와 연료분사 장치를 설치한 구미의 자동 차가 주행중 28MHz, 28W의 아마추어 무선을 탑제한 자동차가 통과할 때 엔진이 고르지 못한 보고가 있 었고, 화학섬유로된 옷을 착용한 전자부품이 다른 부품에 영향을 주는 사례가 맣아지고 있다. 따라서 자동차에는 여러가지의 전장품, 전자기기를 탑재하기 때문에 자동차 자체에서 발생하는 것과 외부로 부터 받는 전자장해 EMI(Electromagnetic Interference), EMS(Electromagnetic Susceptibility) 가 문제로 되어 자동차 및 부품 maker에 의한 EMC(Electromagnetic Compatibility) 평가의 중요성이 고조되고 있다. 차제무전기, 차제무전기, Car-Radio는잡음방해를 많이 받기도 하지만, 잡음원이 되기 도 한다. 또한 Engine 제어, 차속제어, Brake 제어등에 이용되는 전자제품은 방해에 의한 오동작 또는 파괴가 발생하여 주행기능, 안전성에 문제가 야기되지 않도록 해야 한다. 이러한 전자기 환경은 모두 RF(Radio Frequence)와 자동차에서의 전자파 장해 문제의 원이 될 수 있다. 자동차 및 그 부품의 전자기 방해에 관한 규격화는 1987년부터 괄목할 만하게 진행되어 이에 따른 규제 움직임이 IEC(International Electrotechnical Commission: 국제전기기술위원회) 산하의 하부기 구인 CISPR(International Special Committeeon Radio Interference: 국제 무선 장해 특별위원회)가 전자기 방해파에 대한 측정법 통일안을 제안 하였고, ISO(International Standardization Organiza- tion: 국제표준화 기구) 가운데 TC 22/SC3가 자동차의 전장품에 대한 장해를 논의히고 있다. 특히, 자동차의 EMC에 관한 국가 규격은 국제 규격에서 저술한 바와 같이 특별히 규정된 것이 없고 VDE(Verband Deutscher Elektrotechniker: 서독전기기술 협회)와 SAE(Society of Automotive Engi- neers: 자동차 기술자 협회)에서 비교적 활발하고 Jaso(Japanese Automobile Standards Organization: 일본 자동차 표준협회)에서 많이 진행중에 있다. 본 고에서는 자동차의 전자제어에 따른 잡음 발생 요인과 전자파 간섭 관련 자동차 규격과 시험평가 방법에 대해 간단히 소개 하였다.