• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1120-1122
• /
• 2000

Switched Reluctance Motors(SRM) attract much attention in motor because they are reliable and inexpensive. With advance in power electronics and high-speed processors, the performance of SRM has been enhanced greatly But because of its geometric and magnetic structure, the switched reluctance motor naturally creates torque ripples during the commutations of the currents from a supplied phase to an other one. This paper presents the torque ripple reduction using hysteresis current control among of current control techniques.

• Journal of KIEE
• /
• 제11권1호
• /
• pp.62-68
• /
• 2001

In this paper it is proposed an advanced modified sliding mode control of a rotor field oriented control of induction motor. The application of this unconventional control has very good results, such as disturbance rejection and nice dynamic properties. Stability can be guaranteed even in the worst situation. A conventional "sliding mode" controller is characterised by fast switching control signal, which causes the chattering of the drive system. To overcome this problem, a modified law is used, by introducing a hysteresis band and a continuous control, which modifies the conventional law. The control is accomplished with dual TMS320C44 floating-point digital signal processor. The validity of the proposed method was verified by experiment on the propulsion system simulator, used for the development of Korean High-Speed Railway Train(KHSRT).in(KHSRT).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1135-1137
• /
• 2003

The conventional DTC strategy provides a fast torque response even though it has very simple scheme consisted with only two hysteresis band comparators and a switching table for torque and flux control. Drawbacks of the conventional BTC are relatively high torque ripple at low speed and variation of the switching frequency according to motor speed. In this paper, the new direct torque control(BTC) schemes are proposed. Those schemes are based on the torque slope and and flux to reduce the torque ripple.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.397-400
• /
• 2001

This paper presents a implementation of digital sensorless position control system of surface permanent-magnet synchronous motor (SPMSM) drive with a direct torque control (DTC). The system are stator flux and torque observer of stator flux feedback control model that inputs are current and voltage sensing of motor terminal with estimated rotor angle for a low speed operating area, two hysteresis band controllers, an optimal switching look-up table, rotor speed estimator, and IGBT voltage source inverter by using fully integrated control software. The developed sensorless control system are shown a good motion control response characteristic results and high performance features using 1.0 (kW) purposed servo drive SPMSM.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.899-907
• /
• 2014

This paper deals with fault-tolerant control of five-phase induction motor (IM) drives under single-phase open. By exploiting a decoupled model for five-phase IM under fault, the indirect field-oriented control ensures that electromagnetic torque oscillations are reduced by particular magnitude ratio currents. The control techniques are developed by the third harmonic current injection, in order to improve electromagnetic torque density. Furthermore, Proportional Resonant (PR) regulator is adopted to realize excellent current tracking performance in the phase frame, compared with Proportional Integral (PI) and hysteresis regulators. The analysis and experimental results confirm the validity of fault-tolerant control under single-phase open.

• 한국자동차공학회논문집
• /
• 제22권6호
• /
• pp.23-30
• /
• 2014

This paper proposes a dead time compensation method for an AC motor drive using phase current polarity information which is detected based on a digital programmable low-pass filter (PLPF). The polarity detection using the PLPF is an alternative solution of a conventional method which uses a general low-pass filter (LPF) and hysteresis bands in order to avoid jittering due to noises. The PLPF not only adjusts its cutoff frequency according to the synchronous frequency of AC motors but also eliminates a gain attenuation and phase delay which are main problems of the general LPF. Through the PLPF, a fundamental component signal without gain and phase distortions is extracted from the measured raw current signal with noise. By use of the fundamental component, the polarity of current is effectively detected by reducing the hysteresis band. Finally, the proposed method compensates the dead time effects by adding or subtracting average voltage value to voltage references of the controller according to the detected current polarity information. The proposed compensation method is experimentally verified by compared with the conventional method.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권8호
• /
• pp.1261-1267
• /
• 2009

직접토크제어는 일정한 히스테리시스 범위 내에서 전동기의 자속과 토크를 제어하는 방법으로서 최적 스위칭 테이블을 사용한 고정자 전압 공간 벡터에 의해 전동기의 자속과 토크를 제어하게 된다. 그리고 본 논문에서 사용한 센서리스 제어법은 실제 전동기와 수식 모델의 전류가 수렴하도록 고정자 전압을 인가하면 실제 전동기 회전자 속도가 속도 지령치인 수식 모델의 회전자 속도에 접근하는 제어방식이다. 이 방식들을 접목하면 PI 제어기가 필요하지 않는 간단하면서도 강인한 제어를 구현할 수 있는데 본 논문에서는 컴퓨터 모의실험을 통해 이의 유효성을 입증한다.

• Journal of Power Electronics
• /
• 제12권1호
• /
• pp.75-82
• /
• 2012

Elimination of rotor position sensors mechanically coupled with the rotor shaft is attractive to variable speed drives primarily due to increased system reliability and cost reduction. In this regard, search for a simple and robust position sensorless control has been intensified in past few years specifically for low-cost, high-volume applications such as home appliances. This paper describes a new parameter insensitive position sensorless control for switched reluctance motor (SRM) drives satisfying such a need in this market segment. Two consecutive switch-on times of the controllable switch in hysteresis current control are compared to estimate the rotor position and speed. The proposed sensorless control algorithm is very simple to implement since it does not depend on extensive computation or any additional hardware. In addition, the proposed method is robust in that its dynamic performance is least affected by system parameter variations. The proposed approach is demonstrated on a single-controllable-switch-converter-driven SRM with two-phases that lends itself to a system with low cost and compact packaging which comes close to the intended applications. Analysis and simulation results followed by experimental verification are presented to demonstrate the feasibility of the proposed sensorless control method.

• 전기학회논문지
• /
• 제56권1호
• /
• pp.57-65
• /
• 2007

Along with the development of power electronics and magnetic materials, permanent magnet (PM) brushless direct current (BLDC) motors are now widely used in many fields of modern industry BLDC motors have many advantages such as high efficiency, large peak torque, easy control of speed, and reliable working characteristics. However, Compared with the other electric motors without a PM, BLDC motors with a PM have inherent cogging torque. It is often a principle source of vibration, noise and difficulty of control in BLDC motors. Cogging torque which is produced by the interaction of the rotor magnetic flux and angular variation in the stator magnetic reluctance can be reduced by sinusoidal air-gap flux density waveform due to reduction of variation of magnetic reluctance. Therefore, this paper will present a design method of magnetizing system for reduction of cogging torque and low manufacturing cost of BLDC motor with isotropic bonded neodynium-iron-boron (Nd-Fe-B) magnets in ring type by sinusoidal air-gap flux density distribution. An analytical technique of magnetization makes use of two-dimensional finite element method (2-D FEM) and Preisach model that expresses the hysteresis phenomenon of magnetic materials in order for accurate calculation. In addition, For optimum design of magnetizing fixture, Factorial design which is one of the design of experiments (DOE) is used.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권3호
• /
• pp.150-157
• /
• 2002

This paper presents preliminarily an implementation of digital high-performance motion control system of Reluctance Synchronous Motor (RSM) drives with direct torque control (DTC). The system consist of stator flux observer, torque estimator, two hysteresis band controllers, an optimal switching look-up table, IGBT voltage source inverter, and TMS320F240 DSP controller made by Texas Instruments. The stator fluff observer is based on the combined voltage and current model with stator flux feedback adaptive control, and the input of the observer are the stator voltage and current of motor terminal for wide speed range. The rotor position and speed sensor used 6000 pulse/rev encoder. In order to prove rightness of the suggested control algorithm, we have some simulation and actual experimental system at $\pm$20 and $\pm$2000 rpm. The developed digitally high-performance motion control system+ are shown a good response characteristic of control results and high performance features using 1.0kW RSM which has 2.57 Ld/Lq salient ratio.