• Current Optics and Photonics
• /
• v.7 no.1
• /
• pp.21-27
• /
• 2023

A highly sensitive optical-fiber humidity sensor is demonstrated in this paper. By using Nafion-PVA sol-gel and single-mode optical fibers, the Fabry-Perot humidity sensor is easily fabricated. In the humidity range of 29%-72%, humidity-response experiments are carried out with a cycle of rising and falling humidity to investigate humidity-response characteristics. The experimental results show 2.25 nm/%RH sensitivity and a 0.9997 linear correlation coefficient, with good consistency. The changes in optical-path difference (OPD) and free spectral range (FSR) with humidity are also discussed. The humidity sensitivities of a typical sensor are 80.3 nm/%RH (OPD) and 0.03 nm/%RH (FSR). Furthermore, many humidity sensors with different Nafion-PVA sol-gel concentration and initial cavity length are experimentally investigated for humidity response. The results show that the sensitivity increases with higher Nafion ratio of the Nafion-PVA sol-gel. The influence of changing cavity length on sensitivity is not obvious. These results are helpful to research on optical-fiber humidity sensors with good performance, easy fabrication, and low cost.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.521-525
• /
• 2004

Crystalline carbon nitride films were attempted for an application of humidity sensors. The films were deposited on $Al_2$O$_3$substrate having intermigrated electrodes by reactive rf magnetron sputtering system. The film revealed a good humidity-resistance characteristics as well as humidity-capacitance ones in the humidity range of 10∼95 RH(%). Temperature dependence was also investigated. These results suggest that the carbon nitride film has a possibility for new humidity-sensitive material.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.88-91
• /
• 2003

Crystalline carbon nitride films have been attempted for an application of humidity sensors. The films were deposited on $Al_2O_3$ substrate having interdigitated electrodes by reactive RF magnetron sputtering system. The film revealed a good humidity-resistance characteristics as well as humidity-capacitance ones in the humidity range of $10\;{\sim}\;95\;RH(%)$. Temperature dependence was also investigated. These results suggest that carbon nitride film have a possibility for a new humidity-sensitive materials.

• Journal of Sensor Science and Technology
• /
• v.7 no.2
• /
• pp.83-89
• /
• 1998

$TiO_{2-x}$ thin film humidity sensors have been fabricated by sputtering method and their physical and hygroscopic characteristics have been investigated. The sputtering conditions and sintering conditions affect the sensor's sensitivity toward humidity. AES and SEM micrographs were taken for the analysis of crystal structures, surface morphology caused by adsorbed water vapour. $TiO_{2-x}$ humidity sensors showed negative impedance-humidity characteristics and the sensor which was fabricated by experimental condition 2(rf power of 200W) showed higher sensitivity and linearity than others. Then the slope of the sensor was about $0.794\;K{\Omega}/%RH$ and the response time of $TiO_{2-x}$ humidity sensors was about 2 min. for adsorption and about 3 min. for desorption at the operating temperature of $30^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.1014-1016
• /
• 1998

A capacitance-type humidity sensor using porous silicon layer is developed. The unique property of this sensor is a structure which has electrodes on the surface of the wafer like a general IC device. To do this. the sensor was fabricated using process such as localized formation of porous silicon, oxidation of porous silicon layer, and etching of oxidized porous silicon layer. The measurement of humidity-sensing ability was done for two type of sensors using porous silicon layer formed in 25 and 35% HF solutions, respectively. As the result, the former sensors showed larger value and variation of capacitance for the relative humidity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.05a
• /
• pp.129-133
• /
• 1993

$TiO_2-V_2O_5-Nb_2O_5$ humidity sensors have been fabricated in the ceramic type and their physical and hygroscopic characteristics have been investigated. The additives and sintering conditions affect the humidity sensitivity. XRD patterns, SEM photographs were used for the analysis of crystal structures and surface morphology. $TiO_2-V_2O_5-Nb_2O_5$ humidity sensors had good linearity in the range from 20%RH to 90%RH and the sensitivity of sensor sintered at $1,000^{\circ}C$ for 1hr was 73% at operating temperature $60^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1422-1424
• /
• 1994

This paper deals with piezoresistive humidity sensor using polycrystalline silicon (Poly-Si ) with membrane in sensors of semiconductor. Poly-Si piezoresistors which have no temperature dependancy are deposited on silicon wafer, membrane is formed with micromachining technology, then polyimide is formed as a hygroscopic layer. Whereas the principle of conventional humidify sensors are based on the change in electrical properties of the material, the humidity induced volume change of a polyimide layer leads to a deformation of a silicon membrane in this case. This deformation is transformed into an output voltage by Poly-Si piezoresistive. Wheatstone bridge. Fabricated piezoresistive humidity sensors showed good linearity, response time, and long term stability.

• Journal of Sensor Science and Technology
• /
• v.26 no.3
• /
• pp.179-185
• /
• 2017

This article describes the characteristics of nondispersive infrared carbon dioxide gas sensor according to the temperatures and humidifies. In this researches, a thermopile sensor that included application-specific integrated circuit (ASIC) was used and the White-cell structure was implemented as an optical waveguide. The developed sensor modules were installed in gas chamber and then the temperature of gas chamber has been increased from 283 K to 313 K with 10K temperature step. In order to analyze the effects of humidity levels, the relative humidity levels were changed from 30 to 80%R.H. with small humidifier. Then, the characteristics of sensor modules were acquired with the increment of carbon dioxide concentrations from 0 to 2,000 ppm. When the initial voltages of sensors were compared before and after humidifying the chamber at constant temperature, the decrements of the output voltages of sensors are like these: 9mV (reference infrared sensor), 41 mV (carbon dioxide sensor), 2 mV (temperature sensor). With the increment of ambient temperature, the averaged output voltage of carbon dioxide sensor was increased 19 mV, however, when the humidity level was increased, it was decreased 14mV. Based upon the experimental results, the humidity effect could be alleviated by the increment of temperature, so the effects of humidity and temperature could be only compensated by the ambient temperature itself. The estimated carbon dioxide concentrations showed 10% large errors below 200 ppm, however, the errors of the estimations of carbon dioxide concentrations were less than ${\pm}5%$ from 400 to 2,000 ppm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.347-348
• /
• 2007

On-chip micro humidity sensor, using $CN_x$ films for the sensing material, was designed, simulated, and fabricated with Op amp based readout circuit and diode temperature sensors. To compensate the temperature and other gases, two methods were applied. One is wheatstone-bridge with reference FET that eliminates other undesirable chemical species, and the other is a diode temperature sensor to compensate the temperature effect. $CN_x$ film can be a new humidity sensing material, and has a strong potential to adapt to smart sensors or multi-sensors using MEMS or nano-technology. A particular design technology for integration of sensors and systems together was proposed that whole fabrication process could be achieved by a standard CMOS process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.5
• /
• pp.314-320
• /
• 2021

Controlling ambient humid condition through high performance humidity sensors has become important for various fields, including industrial process, food storage, and the preservation of historic remains. Although aerosol deposited humidity sensors using ceramic BaTiO₃ (BT) material have been widely studied because of their longtime stability, there remain critical disadvantages, such as low sensitivity, low linearity, and slow response/recovery time in case of the sensors fabricated at room temperature. To achieve superior humidity sensing properties even at room temperature condition, BT-Cu composite films utilizing aerosol deposition (AD) process have been proposed based on the percolation theory. The BT-Cu composite films showed gradually improved sensing properties until the Cu concentration reached 15 wt% in the composite film. However, the excessive Cu (above 30 wt%) containing BT-Cu composite films showed a rapid decrease of the sensing properties. The results of observed surface morphology of the AD fabricated composite films, to figure out the metal filler effect, showed correlation between surface topography as well as size and the amount of open pores according to the metal filler content. Overall, it is very important not only dielectric constant of the humidity sensing films but also microstructures, because they affect either the variation range of capacitance by ambient humidity or adsorption/desorption of ambient humidity onto/from the humidity sensing films.