• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.339-346
• /
• 1999

A RF receiver section for INMARSAT-C external mounting unit was designed, fabricated and evaluated. Using a INA-03184, the high gain amplifier consists of matched amplifier type. Active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilization resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver section implemented here show 60 dB in gain, 44.83 dBc in a spurious level. The voltage standing wave ratios(VSWR)of input output port are less than 1.8:1, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.4A
• /
• pp.214-218
• /
• 2012

In this paper, we reported on a high performance waveguide VCO(voltage controlled oscillator) for FMCW applications. The waveguide VCO consists of a GaAs Gunn diode, a varactor diode, and two bias posts with low pass filter(LPF). The cavity is designed for fundamental mode at 47 GHz and operated at second harmonic of 94 GHz center frequency. The developed waveguide VCO has 1.095 GHz bandwidth, 590 MHz linearity with 1.69% and output power from 14.86 to 15.93 dBm. The phase noise is under -95 dBc/Hz at 1 MHz offset.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2311-2317
• /
• 2011

In this paper, we study the temperature change of a ${\mu}$-bolometer focal plane array with a capacitive transimpedance amplifier bias cancellation circuit. Thermal analysis is essential to understand the performance of a ${\mu}$-bolometer focal plane array, and to improve the temperature stability of a focal plane array characteristics. In this study, the thermal analyses of a ${\mu}$-bolometer and its two reference detectors are carried out as a function of time. The analyses are done with the $30{\mu}m$ pitch $320{\times}240$ focal plane array operating of 60 Hz frame rate and having a columnwise readout. From the results, the temperature increase of a ${\mu}$-bolometer in FPA by an incident IR is estimated as $0.689^{\circ}C$, while the temperature increase by a pulsed bias as $7.1^{\circ}C$, which is about 10 times larger than by IR. The temperature increase of a reference detector by a train of bias pulses may be increased much higher than that of an active ${\mu}$-bolometer. The suppression of temperature increase in a reference bolometer can be done by increasing the thermal conductivity of the reference bolometer, in which the selection of thermal conductivity also determines the range of CTIA output voltage.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.302.1-302.1
• /
• 2016

Solution-processed amorphous metal-oxide thin-film transistors (TFTs) are considered as promising candidates for the upcoming transparent and flexible electronics due to their transparent property, good performance uniformity and possibility to fabricate at a low-temperature. In addition, solution processing metal oxide TFTs may allow non-vacuum fabrication of flexible electronic which can be more utilizable for easy and low-cost fabrication. Recently, for high-mobility oxide TFTs, multi-layered oxide channel devices have been introduced such as superlattice channel structure and heterojunction structure. However, only a few studies have been mentioned on the bias illumination stress in the multi- layered oxide TFTs. Therefore, in this research, we investigated the effects of bias illumination stress in solution-processed bilayer oxide TFTs which are fabricated by the deep ultraviolet photochemical activation process. For studying the electrical and stability characteristics, we implemented positive bias stress (PBS) and negative bias illumination stress (NBIS). Also, we studied the electrical properties such as field-effect mobility, threshold voltage ($V_T$) and subthreshold slop (SS) to understand effects of the bilayer channel structure.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.2
• /
• pp.235-245
• /
• 2014

This paper presents an envelope tracking power amplifier using a standard CMOS process for the 3GPP long-term evolution transmitters. An efficiency of the CMOS power amplifier for the modulated signals can be improved using a highly efficient and wideband CMOS bias modulator. The CMOS PA is based on a two-stage differential common-source structure for high gain and large voltage swing. The bias modulator is based on a hybrid buck converter which consists of a linear stage and a switching stage. The dynamic load condition according to the envelope signal level is taken into account for the bias modulator design. By applying the bias modulator to the power amplifier, an overall efficiency of 41.7 % was achieved at an output power of 24 dBm using the 16-QAM uplink LTE signal. It is 5.3 % points higher than that of the power amplifier alone at the same output power and linearity.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.707-712
• /
• 2006

In this paper, dual bias control circuit and PBG(Photonic BandGap) structure have been employed to improve PAE(Power Added Effciency) of the Doherty amplifier on Input power level. The gate and drain bias voltage has been controlled with the envelope of the input RF signal and PBG structure has been employed on the output port of Doherty amplifier. The proposed Doherty amplifier using dual bias controlled circuit and PBG has been improved the average PAE by 8%, $IMD_3$ by -5 dBc. And proposed Doherty amplifier has a high efficiency more than 30% on overall input power level, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.27-30
• /
• 2002

Photoconductor for direct detection flat-panel imager present a great materials challenge, since their requirements include high X -ray absorption, ionization and charge collection, low leakage current and large area deposition. Selenium is practical material. But it needs high thickness and high voltage in selenium for high ionization rate. We report comparative studies of detector sensitivity. One is an a-Se with $70{\mu}m$ thickness on glass. The other has hybrid layer of depositting ZnS phosphor with $100{\mu}m$ on a-Se. The leakage current of hybrid is similar to it of a-Se, but photocurrent is lager than a-Se. Both of them have high spatial resolution, but hybrid has higher sensitivity than a-Se at comparable bias voltage.

• Electrical & Electronic Materials
• /
• v.9 no.8
• /
• pp.813-818
• /
• 1996

Amorphous As$_{10}$Ge$_{15}$ Te$_{75}$ device shows the memory switching characteristics under d.c. bias. In bulk material, a-As$_{10}$Ge$_{15}$ Te$_{75}$ switching threshold voltage (V$_{th}$) is very high (above 100 volts), but in the case of thin film, V$_{th}$ decreases to a few or ten a few volts. The characteristics of V$_{th}$ depends on the physical dimensions such as the thickness of thin film and the separation between d.c. electrodes, and the annealing conditions. The switching threshold voltage decreases exponentially with increasing annealing temperature and annealing time, but increases linearly with the thickness of thin film and exponentially with increasing the separation between d.c. electrodes. The desirable low switching threshold voltage, therefore, can be obtained by the stabilization through annealing and changing physical dimensions.imensions.sions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1301-1304
• /
• 2007

We have investigated degradation of short channel n-type poly-Si TFTs with LDD under high gate and drain voltage stress due to self-heating. We have found that the threshold voltage of short channel TFT is shifted to negative direction on the selfheating stress, whereas the threshold voltage of long channel is moved to positive direction.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.256-258
• /
• 2010

MPM(Microwave Power Module)은 진공 전력증폭기인 진행파관(TWT,Traveling Wave Tube)과 반도체 전력증폭기(SSA, Solid State Amplifier)를 결합한 구조로서, 미세한 RF신호를 입력 받아 고출력의 RF 신호로 증폭하는 장치이다. 본 논문은 MPM을 구동하기 위해, 필요한 수 kV이상의 높은 전압을 TWT에 공급해주는 고전압 전원공급기(HVPS, High Voltage Power Supply)에 관한 것이다. Main Topology는 Resonant Phase Shift Full Bridge Converter이며, 승압의 효과를 높이기 위해 2차 측에는 Voltage Multiplier를 사용하였다. MPM을 구동하는데 필요한 전압인Cathode(-4kV), FE_Bias(-5.25kV), Collector(-2kV)를 생성하며, FE_ON, OFF신호에 따라 고전압 스위칭 동작을 하여, RF 증폭을 제어 할 수 있다. 최종적으로 Prototype을 제작하고, 고찰된 실험결과를 제시하여 개발된 HVPS의 우수성을 검증한다.