• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.30-33
• /
• 1997

In this paper, we studied the variation in optical constants of Te-doped G $e_{15}$ /$Sb_{85}$ thin films with 7800$\AA$ diode-laser exposing time and power. The reflectances were increased with the increase of laser exposure time and the laser power in all films. Also, the refractive indices of the films after exposing were higher than those of the as-deposited films. Thus, the fast crystallization was caused by addition to the more Te content at the lower lacer power. It was observed that the surface morphologies of the exposed films are higher than those of the as-deposited films by SEM analysis. Therefore, it is considered that the T $e_{0.5}$(G $e_{15}$ /$Sb_{85}$)$_{99.5}$ thin films will show the high contrast ratio and high SNR and have fast erasing time due to crystallization when these films is applied to optical recording materials.terials.s.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.177-180
• /
• 2007

The laser welding process was effective way to join the metals, because of the high productivity, the low distortion and the good weld quality. The fiber laser used the double-clad fiber architecture, the single element diode laser and the fully-spliced side pumping. It has the advantages in the views of the energy conversion efficiency, the beam quality, the robustness and the mobility. Recently, the thick material was welded with the high power laser in ship building or construction industry owing to the super bright fiber laser. In this study, we introduced the characteristics of high power fiber laser and its welding performance of thick gauge materials.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.5
• /
• pp.746-750
• /
• 2015

In this paper, we propose a simulator to evaluate the performance of the semi-active laser guidance or the quadrant photodetector and to simulate the laser power reflected from a target. The laser pulse repetition frequency was generated and synchronized with the laser pulse repetition(PRF) code. To evaluate the performances of the proposed methods, we implemented a prototype system and performed experiments. As a result, the generated high voltage was variable in the range of DC 3V to 340V and has the rate of change of 2000 V/s. PRF code can be generated within 50ms ∼ 100ms and the error is implemented within 0.3ns. The laser output is synchronized with the PRF code and has a dynamic range of 23.6dB.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.5
• /
• pp.600-607
• /
• 2011

Recently, high carbon steel has become essential not only for shipbuilding parts, but also mass production. Its surface has been treated by carburizing, nitriding and induction hardening, but these existing treatments cause considerable deformation and increase the expense of postprocessing after treatment; furthermore, these treatments cannot be easily applied to parts that requiring the hardening of only a certain section. This is because the treatment cannot heat the material homogeneously, nor can it heat all of it. Laser surface treatment was developed to overcome these disadvantages, and when the laser beam is irradiated on the surface and laser speed is appropriate, the laser focal position is rapidly heated and the thermal energy of surface penetrates the material after irradiation, finally imbuing it with a new mechanical characteristic by the process of self-quenching. This research estimates the material characteristic after efficient and functional surface treatment using HPDL, which is more efficient than the existing CW Nd:YAG laser heat source. To estimate, microstructural changes and hardness characteristics of two parts (the surface treatment part, and parental material) are observed with the change of laser beam speed and surface temperature.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.583-589
• /
• 2019

We report experimental results on 940-nm 350-mW AlGaAs/InGaAs transverse single-mode laser diodes (LDs) adopting graded-index separate confinement heterostructures (GRIN-SCH) and p,n-clad asymmetric structures, with improved temperature and small-divergence beam characteristics under high-output-power operation, for a three-dimensional (3D) motion-recognition sensor. The GRIN-SCH design provides good carrier confinement and prevents current leakage by adding a grading layer between cladding and waveguide layers. The asymmetric design, which differs in refractive-index distribution of p-n cladding layers, reduces the divergence angle at high-power operation and widens the transverse mode distribution to decrease the power density around emission facets. At an optical power of 350 mW under continuous-wave (CW) operation, Gaussian narrow far-field patterns (FFP) are measured with the full width at half maximum vertical divergence angle to be 18 degrees. A threshold current (I_th) of 65 mA, slope efficiency (SE) of 0.98 mW/mA, and operating current (I_op) of 400 mA are obtained at room temperature. Also, we could achieve catastrophic optical damage (COD) of 850 mW and long-term reliability of 60℃ with a TO-56 package.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.16-20
• /
• 2004

We present the fabrication and performance of wavelength tunable butt coupled (BT) sampled-grating (SG) distributed bragg reflector (DBR) - planar buried heterostructure (PBH) laser diodes (LD). The fabricated LD showed the high optical output power due to the high coupling efficiency between active and passive components by the BT coupling methods. The series resistance and diode ideality factor of LD were measured to be 3.7 $\Omega$ and 1.35, respectively. The average threshold current was 25 ㎃. The output powers of BT-SG DBR-PBH-LD were obtained to be as high as 12.3 and 24.56 ㎽ at 100 and 200 ㎃, respectively. The maximum wavelength tuning range was about 31 nm and the side mode suppression ratio was about 37 dB.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.14 no.6
• /
• pp.321-327
• /
• 2019

Spectral Beam Combining (SBC) is used for a high-power fiber laser in order to overcome the power limitation of single fiber laser. In SBC, several laser bwams with different wavelengths are combined to obtain a single-aperture beam by diffraction grating. The combining efficiency is dependent on a linewidth, beam quality and specific wavelength of each beam among others. In this paper, we consider the method of a wavelength monitoring and a feedback control of laser diodes used as seeds of laser beams to obtain optimum combining conditions. In order to measure the wavelengths of multi-beam, we use the high resolution camera and diffraction grating with 1,800l/mm. The experiment results show the possibility of feedback control of a current and temperature of multi-seed laser diodes to obtain optimum wavelengths for SBC.

• Korean Journal of Optics and Photonics
• /
• v.6 no.3
• /
• pp.222-227
• /
• 1995

A single mode, 100-mW diode laser was injection-locked by the master laser which was spectrally narrowed with Littman-type grating feedback. In the incomplete-injection-locking, we observed that two frequencies were simultaneously generated from the slave laser. The power ratio and frequency shift of two frequency components were proportional to the square of injected laser intensity. When the ratio of the injection intensity to the slave laser intensity was about $10^{-3}$, the injection-locking bandwidth was to be about 1.4 GHz. The bandwidth proportionally increased to the square root of the injection intensity, which was in good agreement with the theoretical predictions. The Iinewidth of the locked-laser was about 2.5 MHz, which was five times as narrow as that of free-running operation. ation.

• Korean Journal of Optics and Photonics
• /
• v.20 no.5
• /
• pp.276-280
• /
• 2009

A Cr:YAG crystal was used as a saturable absorber for passive Q-switching of a Nd:$YVO_4$ laser which was pumped by a 1-W continuous wave laser diode. The first surface of the Cr:YAG was high-reflection coated for the pump wavelength. The high-reflection coating improved the absorption efficiency of the pump beam in the Nd:$YVO_4$ through double pass absorption. It also prevented pump beam induced partial bleaching of the Cr:YAG. The peak-to-peak pulse fluctuation of passively Q-switched laser output was approximately 4 %. The minimum pulse-width was measured to be 7.11 ns. Also, the average pulse repetition rate was 9 kHz and the maximum output power was 16.27 mW.

• Korean Journal of Optics and Photonics
• /
• v.11 no.6
• /
• pp.434-440
• /
• 2000

We fabricated a high power Nd:YAG laser pumped by a 1 kW diode laser with a Lambertian-type diffusive reflector. Maximum cw power of 500 W with a slope efficiency of 49%, which corresponds to an optical efficiency of 46.7%, was obtained from a short linear resonator when a 5 mm rod was used. The efficiencies decreased when a 6 mm rod was used, due to the poor quality of the absorption distribution in the rod. The measured beam quality factor of 70, which is slightly smaller than the value calculated from the measured thermal focal lengths, shows that the absorption distribution in the rod is fairly uniform. iform.