• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.1
• /
• pp.119-127
• /
• 2012

This paper describes development and performance test of signal processor for the millimeter wave seeker. A ground to air guidance missile is required various beam patterns in order to counteract different kind of target. Therefore, we designed the hardware and software architecture considering flexibility. This signal processor consists of ADC, FPGA, DSP and etc. FPGA provides peripheral interface to DSP and convert digital IF signal to baseband signal. DSP performs signal processing, calculates target's information and controls devices. Each parts' hardware are connected in series and signal processing algorithms for various beam patterns are built in parallel.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.7
• /
• pp.648-655
• /
• 2002

This paper describes implementation of a multi-channel G.723.1 Annex A (G.723.1A) focused on code optimization using a high performance general purpose Digital Signal Processor (DSP), To implement a multi-channel G.723.1A functional complexities of the ITU-T G.723.1A fixed-point C-code are measures an analyzed. Then we sort and optimize C functions in complexity order. In parallel with optimization, we verify the bit-exactness of the optimized code using the ITU-T test vectors. Using only internal memory, the optimized code can perform full-duplex 17 channel processing. In addition, we further increase the number of available channels per DSP into 22 using fast codebook search algorithms, referred to as bit -compatible optimization.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.3
• /
• pp.323-328
• /
• 2008

This paper presents a Digital Signal Processor achieving high through-put for both decision intensive and computation intensive tasks. The proposed processor employees a multiplier, two ALU and load/store. Unit as operational units. Those four units are controlled and works parallel by superscalar control scheme, which is different from prior DSP architecture. The performance evaluation was done by implementing AC-3 decoding algorithm and 37.8% improvement was achieved. This study is valuable especially for the consumer electronics applications, which require very low cost.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.661-664
• /
• 2000

This paper presents a digital instrument for the power quality analysis in three phase power system where current waveform is non-sinusoidal. It is based on C31 DSP and on a special high-speed data acquisition system. Voltage and current waveforms are acquired and processed by using a simple average power algorithm, The paper also goes on to discuss the performance of an instrument prototype both in terms of accuracy and speed of measurement.

• International journal of advanced smart convergence
• /
• v.2 no.1
• /
• pp.32-35
• /
• 2013

In this paper we proposed a PTZ camera system which automatically detect and track moving objects in the image. Once a moving object is detected the PTZ camera traces it in real-time. We proposed the control system which does not depend on camera focusing functionality but uses the object's center, moving direction, distance and speed. We implemented the system with the TI DM6446 DSP chip. The experimental result shows that the system has excellent performance for high speed vehicles.

• Journal of Power Electronics
• /
• v.11 no.2
• /
• pp.113-119
• /
• 2011

This paper presents a DSP based direct digital control design and implementation for a high power boost converter. A single loop and dual loop voltage control are digitally implemented and compared. The real time workshop (RTW) is used for automatic real-time code generation. Experimental results of a 20 kW boost converter based on the TMS320F2808 DSP during reference voltage changes, input voltage changes, and load disturbances are presented. The results show that the dual loop control achieves better steady state and transient performance than the single loop control. In addition, the experimental results validate the effectiveness of using the RTW for automatic code generation to speed up the system implementation.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.155-160
• /
• 2002

In this paper, a controller design for brushless linear motor is implemented. The designed controller is mainly composed of current, speed and position controller, which are carried out by the high-speed digital signal processor (DSP). In addition the PWM inverter is controlled by space voltage PWM method. This system is implemented by using 32-bit DSP (TMS320C31), a high-integrated logic device (EPM7192), and IPM (Intelligent Power Module) for compact and powerful system design. The experimental results show the effective performance of controller for the brushless linear motor.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.342-344
• /
• 1997

Owing to technical advances in very large-scale integrated circuits (VLSI), high-speed digital signal processing (DSP) chips become fast enough to allow for real-time implementation of hearing aid algorithms in units small enough to be wearable. In this paper, we present a digital hearing aid processor (DHAP) chip built around a general-purpose 16-bit DSP core. The designed DHAP performs a nonlinear loudness correction of 8 octave frequency bands based on audiometric measurements. By employing a programmable DSP, the DHAP provides all the flexibility needed to implement audiological algorithms. In addition, the has a low power feature and $5.410\times5.720mm^2$ dimensions that fit for wearable devices.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.923-928
• /
• 1990

This paper describes the design and implementation of a real-time, high-precision vision system and its application to SMT(surface mounting technology) automation. The vision system employs a 32 bit MC68030 as a main processor, and consists of image acquisition unit. DSP56001 DSP based vision processor, and several algorithmically dedicated hardware modules. The image acquisition unit provides 512*480*8 bit image for high-precision vision tasks. The DSP vision processor and hardware modules, such as histogram extractor and feature extractor, are designed for a real-time excution of vision algorithms. Especially, the implementation of multi-processing architecture based on DSP vision processors allows us to employ more sophisticated and flexible vision algorithms for real-time operation. The developed vision system is combined with an Adept Robot system to form a complete SMD system. It has been found that the vision guided SMD assembly system is able to provide a satisfactory performance for SND automation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.82-92
• /
• 2008

Recently, many digital signal processing(DSP) applications such as H.264, CDMA and MP3 are predominant tasks for modern high-performance portable devices. These applications are generally computation-intensive, and therefore, require quite complicated accelerator units to improve performance. Designing such specialized, yet fixed DSP accelerators takes lots of effort. Therefore, DSPs with multiple accelerators often have a very poor time-to-market and an unacceptable area overhead. To avoid such long time-to-market and high-area overhead, dynamically reconfigurable DSP architectures have attracted a lot of attention lately. Dynamically reconfigurable DSPs typically employ a multi-functional DSP accelerator which executes similar, yet different multiple kinds of computations for DSP applications. With this type of dynamically reconfigurable DSP accelerators, the time to market reduces significantly. However, integrating multiple functionalities into a single IP often results in excessive control and area overhead. Therefore, delay and power consumption often turn out to be quite excessive. In this thesis, to reduce power consumption of dynamically reconfigurable IPs, we propose a novel fine-grained clock gating scheme, and to reduce size of dynamically reconfigurable IPs, we propose a compact multiplier-less multiplication unit where shifters and adders carry out constant multiplications.