• Korean journal of food and cookery science
• /
• v.12 no.1
• /
• pp.54-59
• /
• 1996

Immunoglobulins (IgY) were isolated from egg yolk of hens immunized with bovine serum albumin(BSA). The stability of anti-BSA IgY against heat and pH was investigated. Antibody activity was measured by enzyme linked immunosorbent assay. IgY was relatively heat-stable and most of the antibody activity remained after heating up 65$^{\circ}C$ for 30 minutes. IgY was stable at pH 5-11. However, inactivation of IgY was observed below pH 4, or above pH 12. Inactivation of IgY proceeded rapidly at low pHs(pH 2-3). Most of the antigen binding activity was lost at low pHs probably because of some conformational changes.

• Journal of Ginseng Research
• /
• v.6 no.1
• /
• pp.25-29
• /
• 1982

This investigation was carried out to study the influence of pH and heat treatment on the ginsenosides in the white ginseng extract. Changes in ginsenosides (Rb1, Rb2, ,Rc, Rd) and free sugar were measured by the peak area variation of HPLC chromatogram during 25 hours heat treatment at the various level of pH. It was found that :(1) The peak areas of Rb1. Rb2, Rc and Rd on the HPLC chromatogram were decreased remarkably below pH 4.0 and more decrease was found as the temperature and heating time increased. (2) Those of glucose and arabinose were increased remarkably. It is considrered that the increase of glucose and the formation of arabinose result from the hydrolysis of ginsenoside( Rb1, Rb2, Rc, Rd) linked with sugars.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.5
• /
• pp.680-686
• /
• 1998

In the adoption of a desalination system the most important factor is the cost of fresh water pro-duction. In general LNG is stored in a tank as a liquid state below $-162^{\circ}C$ When it is serviced however the LNG absorbs energy from a heat source and it is transformed to a high pressure gaseous state. During this process a huge amount of cold energy accumulated in cooling LNG is wasted. This wasted cold energycan be utilized to produce fresh water by using a sea water freez-ing desalination system. in order to develop a sea water freezing desalination system and to estab-lish its design technique qualitative and quantitative data regarding the freezing behavior of sea water is required in advance. The goals of this study are to reveal the freezing mechanisms of sea water in a cooled circular tube to measure the freezing rate and to investigate the freezing heat-transfer characteristics. The experimental results provide a general understanding of sea water freezing behavior in a cooled circular tube.

• Korea-Australia Rheology Journal
• /
• v.17 no.2
• /
• pp.35-40
• /
• 2005

Nanofluid is a novel heat transfer fluid prepared by dispersing nanometer-sized solid particles in traditional heat transfer fluid to increase thermal conductivity and heat transfer performance. In this research we have considered the rheological properties of nanofluids made of CuO particles of 10-30nm in length and ethylene glycol in conjunction with the thermal conductivity enhancement. When examined using TEM, individual CuO particles have the shape of prolate spheroid of the aspect ratio of 3 and most of the particles are under aggregated states even after sonication for a prolonged period. From the rheological property it has been found that the volume fraction at the dilute limit is 0.002, which is much smaller than the value based on the shape and size of individual particles due to aggregation of particles. At the semi-dilute regime, the zero shear viscosity follows the Doi-Edwards theory on rodlike particles. The thermal conductivity measurement shows that substantial enhancement in thermal conductivity with respect to particle concentration is attainable only when particle concentration is below the dilute limit.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.2
• /
• pp.187-194
• /
• 2017

This study examined the validity and reliability of the thermal safety design, in order to maintain the heat generated from integrated circuit (IC) chips in the converter, condenser, resistor, and transistor (which are considered as heat sources for thermoelectric devices with a printed circuit board) below target levels during the process of developing a control board and a main power board. The study analyzed the heat generation and dissipation characteristics of the entire printed circuit board (PCB) model to examine its thermal safety.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.05a
• /
• pp.57-60
• /
• 2008

This study investigated the results of insulation heat curing method using double layer bubble sheet in slab concrete and mass concrete in cold weather environment. First of all, when double bubble sheets are applied, it was shown that slab concrete was protected from early freezing by remaining between 6 and 15℃ even in case outside temperature drops -9℃ below zero until the 2nd day from piling, and in the case of mass concrete, with the maximum temperature difference between the center and surface less than 4℃, crack occurrence index was close to 2 and no hydration heat crack occurred by internal constraint. The insulation heat preservation curing method using the double bubble sheet applied in this field prevented early freezing owing to stable curing temperature management, deterring concrete strength development delay at low temperature, and obtained the needed strength. Also, it was proven that the method is highly effective and economic for cold weather concrete quality maintenance through curing cost reduction like construction period shortening and labor cost reduction, etc by reducing the process of temporary equipment installation and disassembling.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.270-275
• /
• 2003

The heat transfer analysis was conducted for the conceptual design of high level waste canisters. The temperature distribution due to the heat generation from four PWR spent fuel bundles which were contained in a canister located in a borehole 500 m below the surface was obtained. NISA computer program based upon FEM was used for the numerical solution. The temperature distribution in the composite system of $\ulcorner$canister ＋ buffer ＋ tunnel ＋ rock$\lrcorner$ due to heat generation from the spent fuel was obtained. In the case of 40m tunnel spacing and 6m borehole spacing the temperature showed the maximum value of $87.5^{\circ}C$around 15-16 years after disposal and decreased.

• Journal of the Korean institute of surface engineering
• /
• v.19 no.2
• /
• pp.31-43
• /
• 1986

The properties of the electroless nickel deposit mainly depends on the pH of the bath, the plating temperature, and the molar ratio of nickel to hypophosphite but they are also affected by its formulation and concentration of complexing and buffering agents. According to changeing the concentration of triethanolamine and boric acid, phosphorous contents, microsturcture, crystalline, hardness and wear resistance of deposits obtained from ammoniacal alkaline bath were investigated by EPMA, differential thermal analyser, X-ray diffractometer and wear tester. The results are as follows; (1) Increasing concentration of triethanolamine in the bath, the deposits is slightly inclined to increase its phosphorous content(3.7% P). (2) In the as-plated state, the deposits are not crystallized state but they are thermally unstable phase, and they are crystallized with precipitating $Ni_3P$ at 400$^{\circ}C$. (3) The deposit containing 2.3% P has higher hardness value in the as plated and heat treated state at below 300$^{\circ}C$ than those of 3.7% phosphorous deposit (1090Hk). But in the case of heat treating at 400$^{\circ}C$, the former has lower hardness value (1000Hk) than the latter and has remarkably Ni(III) orientation by heat treatment. (4) The 3.7% phosphorous deposit heat treated at 400$^{\circ}C$ has better wear resistance than hard chromium plating.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.11
• /
• pp.719-726
• /
• 2017

An experimental study was performed to investigate the combined effects of the pitch and heat flux of nearby tubes on boiling in a pool as well as the heat transfer from a horizontally-installed tube bundle. For this test, two smooth stainless steel tubes (19 mm outside diameter) were used, and the water was at atmospheric pressure. The pitch of these tubes was varied between 28.5 mm and 95 mm, and the heat flux of the nearby tube altered between 0 and $90kW/m^2$. Enhancements in heat transfer were clearly observed when the heat flux of the nearby tube increased while the heat flux of the test section remained below $40kW/m^2$. The tube pitch was found to have a negligible effect on heat transfer when the pitch was greater than four times larger than the tube diameter. The circulating flow, convective flow, and liquid agitation were all seen to enhance heat transfer; however, the interaction between the flow and coalescence of bubbles was detrimental to heat transfer.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1731-1740
• /
• 1995

Experimental investigations have been made to study the double-diffusive nature of convection of an initially stratified salt-water solution due to heating from below in a rotating cylindrical cavity. The objective is to examine the flow phenomena and the heat transfer characteristics according to the changes in temperature gradient, concentration gradient and rotating velocity of cavity. Thermal and solutal boundary conditions at side wall are adiabatic and impermeable, respectively. The top and bottom plate are maintained each at constant temperature and concentration. The cavity is put into a state of solid body rotation. Like the stationary case, the types of initially-formed flow pattern are classified into three regimes depending on the effective Rayleigh number and Taylor number; stagnant flow regime, single mixed-layer flow regime and successively formed multi-mixed layer flow regime. At the same effective Rayleigh number, the number of initially-formed mixed layer and its growth rate decrease as the effect of rotation increases. The temperature and concentration profiles are both uniform in each layer due to convective mixing in the layered-flow regime, but look both liner in stagnant flow regime and single mixed-layer flow regime. At the interface between adjacent layers, the temperature changes smoothly but the concentration changes rapidly.