• Journal of the Korean Magnetics Society
• /
• v.13 no.6
• /
• pp.221-225
• /
• 2003

Effects of annealing temperature on the crystalline and magnetic properties of YIG films grown by solid phase epitaxy. The eptiaxy films were made by annealing Fe-Y-O amorphous films in the air at 550-1050 $^{\circ}C$ which were sputtered on GGG (111) substrates in a conventional rf sputtering system. Crystallization temperature of Fe-Y-O amorphous films on GGG (111) substrate was between 600 and 650 $^{\circ}C$ which is much lower than that Fe-Y-O powder prepared by sol-gel method. Excellent epitaxial growth of YIG films could be conformed by the facts that the diffraction intensity of YIG (888) plane was comparable with that of GGG (888) plane and full width at half maximum of YIG (888) rocking curve was smaller than 0.14$^{\circ}$ when films were annealed at 1050 $^{\circ}C$. It could be seen that it is necessary to anneal the films at higher temperature for an excellent epitaxy because lattice parameter of YIG films were smaller and the peak of YIG (888) plane is higher and narrower with increasing annealing temperature. Films annealed at higher temperature shows M-H loop with perpendicular anisotropy which was due to 0.15％ lattice mismatch between YIG and GGG.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.173-178
• /
• 2020

A multi-ray model has been used to interpret radio transmission losses in half-canyon structures with slope and to formulate a multi-ray propagation model depending on the angle of slopes. The cut-off angles for the third and fourth paths, which are the slope-sided reflection paths of the transmission and reception radio waves determined by the inclined angles of the slope, were calculated with the height and location of the transmitter and receiver. To predict transmission losses in an inclined plane environment, the embankment environment where the actual slope exists was modeled and simulated to calculate the loss of propagation transmission, and the radio wave transmission loss was confirmed by the measurement for the frequency band 1 to 6 GHz. Simulation results and measurement results showed similar trends in radio transmission loss, and radio transmission loss predictions and measurement results for various terrain information can be used in the design of radio propagation service.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.641-652
• /
• 2007

In this paper, a half-scaled substructure test was performed to evaluate the buckling and structural safety of an existing transmission tower subjected to wind load. A loading scheme was devised to reproduce the dead and wind loads of a prototype transmission tower, which uses a triangular jig that is mounted on the reduced model to which the similarity law of a half length was applied. As a result of the preliminary numerical analysis carried out to evaluate the stability of a specimen for the design load, is was confirmed that the calculated axial forces of tower leg members were distributed to $80{\sim}90%$ of an admissible buckling load. When the substructured transmission tower was loaded by 270% of its maximum admissible buckling load, it was failed due to the local buckling that is occurred in joints with weak constraints for out-of-plane behavior of leg members. By inspection of load-displacement curves, displacements and strains of members, it is considered that this local buckling was due to additional eccentric force by unbalanced deformation because the time that is reached to yielding stress due to the bending moment is different at each point of a same section.

• Composites Research
• /
• v.29 no.5
• /
• pp.236-242
• /
• 2016

In this work, tensile and in-plane shear tests for thermoplastic glass fiber/polypropylene composites were performed at a thermo-forming temperature and their properties were characterized and mathematically expressed by using the non-orthogonal constitutive model. As for the thermo-forming test, half-dome experiments were carried out by varying the usage of a releasing agent and the weight of holders. As results, the optimum final shape having well-aligned symmetry and no wrinkle formation was obtained when the releasing agent was used, and it was found that the careful control of a holding force is crucial to manufacture the healthy product. Furthermore, FEM simulations based on the non-orthogonal model showed similar final shapes and tendency of wrinkle formation with experimental results, and confirmed that wrinkles increase with less holding force and higher punch force is required under high frictional condition.

• Journal of the Korean Society of Costume
• /
• v.33
• /
• pp.5-25
• /
• 1997

The purpose of this study was to analyze the characteristics of the Junk Art represented in the second half 20the century fashion. The highly developed material civilization resulted in human alienations environmental distruption. By this fact human being of the 20the century was to overcome social com-plexity. In this respect this research was focused that how the characteristics of the junk Art was expressed in the second half 20th century fashion. The concepts of the Junk Art lied in the creation of art work in the 2-dimentional plane of 3-dimentional space through the application of all junks (wood pieces industrial debris trash ready-made goods etc) cast by the mod-ern industrial society and the mass production system. Juck Art had been further envigorated in the footstep of the development of the collage method based on the creation of object aes-thetics. And junk artists have untitled social environments with art by assembling junks as a way of exploring the material world of cur-rent society and provided infinite possibilities of expressional medium and technique. Above all junk Art has been reflected in the fashion as well as other art. Especially a lot of the fashion design by the use of junks and the expressive image of junks is produced in the 20th century. That is many of fashion designers have always been aware of what is happening in the arts and have always been able to use the dis-coveries and ideas of the artist to help them solve design problems and creat fashion which are new inventive and reflective of their time. The fashion designers of the junk fashion design could be said to have presented much more possibilities and new development for-mulas to modern fashion design and provided a new order of other formative arts. Unlike the negative and destructive punk cyberpunk fashion junk fashion was a positive and optimistic aesthetics. junk fashion that keeps pace with science and the development of technology is devoted to trying to grasp the real form of ultimate re-ality.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.1 no.4
• /
• pp.59-68
• /
• 1997

In analysis of underground structures, the effects of artificial boundary conditions are considered as one of the major reasons for differences from experimental results. These phenomena can be overcome by using the boundary elements which satisfy the multi-layered half space conditions. The fundamental solutions of multi-layered half-space for boundary element method is formulated satisfying the transmission and reflection of waves at each layer interface and radiation conditions at bottom layer. The governing equations can be obtained from the displacements at each layer which are expressed in terms of harmonic functions. All types of waves can be included using the complete response from semi-infinite integrals with respect to horizontal wavenumbers using expansion of Fourier series and Hankel transformation. Two dimensional Green's functions are derived from cylindrical Navier equations and potentials performing infinite integration in y-direction. In this case, it is effective to transform into two dimensional problem using semi-analytical integration and sinusoidal Bessel function. Some verifications are given to show the accuracy and efficiency of the developed method, and numerical examples to demonstrate the dynamic behavior of underground with various properties.

• Journal of Oral Medicine and Pain
• /
• v.25 no.2
• /
• pp.205-214
• /
• 2000

This study was performed to investigate the relationship between mandibular midline shift and anteroposterior first molar occlusal relation, and their effects on the mandibular height and the occlusal plane angle. For this study, 49 patients with temporomandibular disorders were selected. They did not show facial asymmetry and their facial midline coincide with maxillary dental midline. Upper and lower mandibular impression were taken and the casts were fabricated. Amount and direction of the mandibular midline shift and the anteroposterior shift between the two occluding first molars were measured on the casts. Several items related to height such as mandibular height from top of the articular surface of the condyle to curve changing point between antegonial notch and mandibular angle, condylar height which was the vertical distance from the articular surface to retroepicondyle of the condyle, and sigmoid height from the deepest point of sigmoid notch to the curve changing point and the occlusal plane angle were also measured on the panoramic and on the transcranial radiographs. Correlation between midline shift and anteroposterior first molar relation and comparison between right and left mandibular height by the midline shift and the first molar relation were analysed by SPSS windows program. The results of this study were as follows : 1. Mean amount of midline shift in the subjects with midline shift were 2.0mm for both side, respectively. The first molar relation of the ipsilateral side of midline shift showed Angle class II tendency and the contralateral side showed Angle class III tendency, which meant drift of the dentition to the side of the midline shift. 2. The occlusal plane angle on the panoramic radiograph were $13.0^{\circ}$ in right, and $12.5^{\circ}$ in left side, and their were no correlation between occlusal plane angle and mandibular midline shift and the first molar occlusal relation. 3. Angle's classification for both sides of the first molar relation were same in about half of all the subjects. Amount of deviation from class I first molar relation, however, were decreased in the contralateral side of observed side. 4. Mandibular height of the ipsilateral side to which mandibular midline shift showed tendency of lower than that of the contralateral side, and there was a tendency that the height was higher in class III subjects, then class II subjects, and lower in class I subjects. However, condylar height did not show any difference in the subjects with midline shift and also show no difference by the first molar occlusal relation.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.04a
• /
• pp.451-457
• /
• 2000

In many dynamic problems such as foundation vibrations ultrasonic nondestructive evaluation and blasting analysts are confronted with the problem of wave propagation in an infinite or semi-infinite media. In order to simulate this situation by a finite analytical model provisions must be made to absorb the stress waves arriving at the boundary. Absorbing boundaries are mathematical artifacts used to prevent wave reflections at the boundaries of discrete models for infinite media under dynamic loads. An analytical study is carried out to examine the effectiveness of Lysmer-Kuhlemeyer model one of the most widely used absorbing boundaries. Validity of the absorbing boundary conditions suggested by Lymer-Kuhlemeyer is examined by adopting the solution of Ewing et al. to the problem of plane waves from a harmonic normal force on the surface of an elastic half-space. The Ewing's problem is than numerically simulated using the finite element method on a semi-circular mesh with and without absorbing boundaries which are represented by viscous dashpots. The absorption ratios are calculated by comparing the displacements at the absorbing boundaries to those at the free field without absorbing boudaries.

• Journal of the Korean Mathematical Society
• /
• v.44 no.1
• /
• pp.55-107
• /
• 2007

Let k be an imaginary quadratic field, h the complex upper half plane, and let $\tau{\in}h{\cap}k,\;q=e^{{\pi}i\tau}$. In this article, we obtain algebraic numbers from the 130 identities of Rogers-Ramanujan continued fractions investigated in [28] and [29] by using Berndt's idea ([3]). Using this, we get special transcendental numbers. For example, $\frac{q^{1/8}}{1}+\frac{-q}{1+q}+\frac{-q^2}{1+q^2}+\cdots$ ([1]) is transcendental.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.508-513
• /
• 2003

This paper is concerned with a mixed control with aerodynamic fin and side thrusters applied to an agile missile using two-time scale dynamic inversion and linear time-varying control technique. The nonlinear dynamic inversion method with the weighting function allocates the desired control inputs (aerodynamic fin and side thrusters) to track a reference trajectory, and the time-varying control technique guarantees the robustness for the uncertainties. Closed-loop stability is achieved by the assignment of the extended-mean of these linear time-varying eigenvalues to the left half complex plane. The proposed schemes are validated by nonlinear simulations.