• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.8
• /
• pp.95-103
• /
• 2006

The compositions, the gas properties in motor chamber and the aluminum oxide (Al2O3) particle size for two kinds of solid propellants with approximately 20% aluminum powder have been investigated. The SEM photographs of $Al_2O_3$ taken from nozzle entrance liner show that the aluminized PCP propellant with 47% volumetric fraction AP/HNIW and bimodal oxidizer 200-5 ${\mu}m$ can offer greater possibility for increasing aluminum agglomeration than the aluminized HTPB propellant with 64% volumetric fraction AP and trimodal oxidizer 400-200-6 ${\mu}m$. The nozzle entrance liner of solid rocket motor with the PCP propellant shows greater erosion at 4 circumferential sections in line with grain slots due to the impingement of large particles, but that with the HTPB propellant shows uniform erosion with circumferential angle.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.8
• /
• pp.774-779
• /
• 2009

A numerical modelling was performed to predict unsteady combustion processes for the AP/HTPB/Al propellant in a solid rocket motor. Its results were compared with the experimental data. Temporal pressure development was found to match quite well with measured data. A change in propellant surface was traced using the moving grid. The propellant thickness change was also observed to confirm the erosive burning effect.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.356-359
• /
• 2011

In this study, applicable to Sounding Rocket about the development of high-performance propellant was studied. Sounding Rocket requires generally multistage rocket system for atmospheric research. This study describes the development of two types solid propellant compositions which are based on HTPB/AP for the two-stage rocket. CEA code of NASA and internal ballistic analysis were used for confirming the theoretical performance of designed propellants. The strand burner and JANNAF tensile test was used to measure ballistic and mechanical properties of designed propellants. Finally, static fired test of standard motors was performed to prove the possibility of development.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.91-94
• /
• 2007

The fabrication and firing test of the ignition system for a micro solid propellant thruster are described in the present paper. Pt igniter coil was patterned on the glass membrane that was fabricated by the wet etching process. The thickness of Pt layer was $2000{\AA}$ and the width of igniter pattern was $40{\mu}m$. The thickness and diameter of glass membrane were $15{\mu}m$ and 1 mm, respectively. Ignition test was performed. Successful ignition of HTPB/AP propellant was obtained with an ignition delay of 1.6 s at an input voltage of 12 V. The ignition energy was estimated to be 1.4 J.

• Journal of the Korean Society of Combustion
• /
• v.22 no.3
• /
• pp.47-52
• /
• 2017

The propellant tile and crack which account for the greatest proportion of solid rockets are profoundly affected by viscosity and mechanical properties of solid propellant. In this paper HTPB/AP/Al system propellant has been researched for the viscosity, mechanical properties and burning properties with type and contents of bonding agents. The viscosity of propellant was changed significantly depending on the type and contents of bonding agents, and mechanical properties of HTPB/AP/Al system propellant were also varied. Considering both lower viscosity and stable mechanical properties, the optimum type and contents of bonding agents can be identified as the main factors to the HTPB/AP/Al system propellant.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.39-45
• /
• 2013

Basically, in order to apply solid propellant as ignition source to high energy metal particle combustion system, we analyzed combustion characteristics of the HTPB/AP/Al, HTPE/AP/Al propellants by using a strand burner. The propellants were tested in a high-pressure windowed strand burner, which was pressurized up to 300 psia with pure argon gas. Strand burner was visualized with two quartz windows and ignition was accomplished by a 10 W $CO_2$ laser. The burning rate of propellant was measured with high-speed camera method for frame analysis and photodiode method for combustion time analysis. Emission spectrum was measured with spectrometer at 300 nm ~ 800 nm and 1500 nm ~ 5000 nm and then we analyzed species during propellant combustion.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.215-218
• /
• 2007

Internal Ballistic modeling and performance prediction for solid propellant micro thruster was performed with heat loss to the chamber wall as an important factor of miniaturization. Simple l-D end-burner type thruster and general HTPB-AP type composite propellant were selected for computation model. The results showed that the performance loss with the heat loss to the surroundings becomes larger as the surface-to-volume ratio is increased. In this case, the total impulse was reduced about 3% of the case in adiabatic condition.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.2
• /
• pp.16-26
• /
• 2014

T-Burner tests of an Al/HTPB propellant in conjunction with a Pulsed DB/AB Method were conducted to find an acoustic amplification factor. Aluminum-free and aluminum-heavy propellants were examined. Instant surface ignition was successfully made by the use of a supplementary propellant of fractionally higher reaction rate. With the presence of higher aluminum concentration in the propellants, the pressure perturbations were promptly damped down and the pressure fluctuations were no longer dispersive. Addition of aluminum particles into the propellant was advantageous for stabilizing pressure-coupled unstable waves.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.175-178
• /
• 2008

A Numerical Simulation which uses preconditioning algorithm to examine unsteady combustion processes for the AP/HTPB propellant with a converging-diverging nozzle has been compared with experimental data for solid rocket motor. To analysis reacting flow of solid rocket motor, unsteady pressure, temperature contour was simulated by grid moving of propellant.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.18-25
• /
• 2017

The study for the combustion characteristics of propellants for nozzleless boosters was carried out. The metal fuels of Al and Zr were introduced into solid propellant formulations in order to enhance the density-specific impulse and the high burning rate with low pressure exponent was investigated as the major combustion characteristic of propellant to design nozzleless boosters. The burning rate of Zr-containing propellant was higher than Al-containing propellant and, $13{\mu}m$ Zr-containing propellant exhibited the burning rate of 35 mm/s (at 1000 psi)and pressure exponent of 0.3282. The benefit of using Al and Zr-containing propellant into nozzleless boosters was demonstrated in these results.