• Environmental Analysis Health and Toxicology
• /
• 제20권1호
• /
• pp.57-65
• /
• 2005

Effects of five polycyclic aromatic hydrocarbon (PAHs) constituents (naphthalene, fluorine, fluoranthene, benzo(a)pyrene, pyrene) on fertilization and early development of sea urchin egg, sperm and fertilized egg were investigated. The eggs, sperm and fertilized eggs were exposed to several concentrations of PAHs (1, 10, 100, 1000 and 10000㎍/L). The rate of fertilization and hatching decreased when the eggs and sperm were exposed to aqueous solution of PAHs. Also, Exposure of fertilized eggs with each PAHs did decrease survival and hatching rate. Concentration-dependent toxic effects on the rate of fertilization, hatching, survival and abnormality in A. crassispina were observed following exposure to PAHs (1, 10, 100, 1000 and 10000㎍/L). These data show that PAHs exposure decreased in fertilization success of sea urchin egg and sperm and producted abnormal embryo. It is plausible to suggest that PAHs had the potential to significantly reduce coastal recruitment of sea urchin.

• Restorative Dentistry and Endodontics
• /
• 제16권1호
• /
• pp.87-105
• /
• 1991

The purpose of this experiment was to measure the leaking and solubility of commonly used dental restorative materials - Silux plus (CS), Hi-pol (CH), Clearfil F-II, Fissureseal (FS), Glass-Ionomer cement Fuji Type II (GI), Amalgam Cavex 68 (AM), Zinc Phosphate Cement (ZP) and gutta-percha (GP) and investigate the relation between the solubility and marginal leakage. Disc-shape specimens were fabricated with each material and dipped into deionized water, 0.01M lactic acid and 0.005M KOH solution, thus the total ionic concentrations in each solution was measured with ion chromatograph after 1, 3, and 7 days, respectively. For the solubility test, each specimen was immersed in 0.001M and 0.01M lactic acid for 24 hours, respectively and total weight loss was calculated. Also, Zn leaking through the margin of restorations was measured. The obtained results were as follows: 1. The amounts of eluted ion from the eight materials were most in 0.01M lactic acid and least in deionized water. 2. Of the eight materials, the fluoride release was greatest for glass ionomer cement (GI) in 0.01 M lactic acid after 7 days. 3. In analysis of the divalent cation, Mg was eluted most for zinc phosphate cement (ZP) and Ca for Clearfil F-II (CF) in 0.01M lactic acid after 7 days. 4. In analysis of transition metals, Cu and Zn were detected only. 5. The solubility rate of eight materials was greater in 0.01M lactic acid than in 0.001M for 24 hours, for zinc phosphate cement (ZP) the rate was greatest (5.4%) in 0.001M lactic acid, and amalgam least (0.01%). 6. The Zn concentration of restorative material with Z.P.C base was greater in 0.01M lactic acid than in 0.001M lactic acid.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권1호
• /
• pp.40-47
• /
• 2014

In this paper, $Al_2O_3$ film deposited by thermal atomic layer deposition (ALD) with diluted $NH_4OH$ instead of $H_2O$ was suggested for passivation layer and anti-reflection (AR) coating of the p-type crystalline Si (c-Si) solar cell application. It was confirmed that the deposition rate and refractive index of $Al_2O_3$ film was proportional to the $NH_4OH$ concentration. $Al_2O_3$ film deposited with 5 % $NH_4OH$ has the greatest negative fixed oxide charge density ($Q_f$), which can be explained by aluminum vacancies ($V_{Al}$) or oxygen interstitials ($O_i$) under O-rich condition. $Al_2O_3$ film deposited with $NH_4OH$ 5 % condition also shows lower interface trap density ($D_{it}$) distribution than those of other conditions. At $NH_4OH$ 5 % condition, moreover, $Al_2O_3$ film shows the highest excess carrier lifetime (${\tau}_{PCD}$) and the lowest surface recombination velocity ($S_{eff}$), which are linked with its passivation properties. The proposed $Al_2O_3$ film deposited with diluted $NH_4OH$ is very promising for passivation layer and AR coating of the p-type c-Si solar cell.

• 한국환경과학회지
• /
• 제7권2호
• /
• pp.177-184
• /
• 1998

1981년부터 1990년까지 10년간 발생한 274개의 호우사례를 분류하여,한반도에서 호우시에 나타나는 강수량의 공간분포를 여섯 종류로 나누고 각각의 정관적 특성을 분석하였다. 첫때, 강하게 발달한 지표 저기압에 연관되어 발생하는 호우보다 상, 하층 제트를 동반한 채 발달중인 저기압에 연관되어 발생하는 호우가 많다. 둘째, 재부분의 호우역은 하층 제트의 위치와 방향 그리고 지표 온나전선의 위치에 연관되어 있다. 셋째, 500hPa 면의 저기압 중심이나 기압골의 위치가 서쪽으로 멀어질수록 한반도에어 호우는 고위도에서 발생하는 경향이 있다. 넷째, 한반도에 호우를 초래하는 500hPa의 저기압 중심은 하계몬순의 발달을 따라 서쪽으로 자리잡는 경향이 있으나 해마다 차이가 있다.차이가 있다.

• 한국작물학회지
• /
• 제10권
• /
• pp.57-60
• /
• 1971

한국산 소맥 5품종과 미국산소맥 3품종을 밀과 밀가루의 성분ㆍ회분ㆍ조단백질함량 및 제분율을 조사하였는데 그 성적을 요약하면 다음과 같다. 1. 수분은 한국산밀이 미국산밀보다 품종과 시료에 따른 차가 컸다. 2. 밀의 회분함량이 미국산 밀에서는 경질과 연질에 따라 차가 현저했는데 한국산밀에서는 그렇지 않았다. 3. 제분율은 한국밀중에서는 육성 003 한 품종만이 비교적 높고 기타는 미국밀에 비하여 현저히 낮았다. 4. 밀가루의 회분함량은 품종간의 차를 인정할수 없었다. 5. 밀가루의 조단백질함량은 한국밀보다 미국밀중에 현저히 높은 것이 있었다. 6. 밀의 조단백질함량과 밀가루의 조단백질함량과의 상관은 한국밀에서 보다 미국밀에서 현저하게 높았다.

• 한국전기전자재료학회논문지
• /
• 제31권1호
• /
• pp.6-10
• /
• 2018

Ni germanide (NiGe) is a promising alloy material with small contact resistance at the source/drain (S/D) of Ge MOSFETs. However, it is necessary to reduce the specific contact resistance between NiGe and the doped Ge S/D region in high-performance MOSFETs. In this study, a novel method is proposed to reduce the specific contact resistance between NiGe and p-type Ge (p-Ge) using a Tb interlayer. The specific contact resistance between NiGe and p-Ge was successfully decreased with the introduction of the Tb interlayer. To investigate the mechanism behind the reduction in the specific contact resistance, the elemental distribution and crystalline structure of NiGe were analyzed using secondary ion mass spectroscopy and X-ray diffraction. It is likely that the reduction in specific contact resistance was caused by an increase in the concentration of boron in the space between NiGe and p-Ge due to the influence of the Tb interlayer.

• 한국전기전자재료학회논문지
• /
• 제24권6호
• /
• pp.491-496
• /
• 2011

Al-doped ZnO film on glass substrate is deposited by ALD in low temperature, using 4-step process (DEZ-$H_2O$-TMA-$H_2O$). To find out the optimal film condition for TCO material, we fabricate Al-doped ZnO films by increasing Al doping concentration at $100^{\circ}C$, so that the Al-doped film of 5 at% shows the lowest resistivity ($1.057{\times}10^{-2}{\Omega}{\cdot}cm$) and the largest grain size (38.047 nm). Afterwards, the electrical and physical characteristics in Al-doped films of 5 at% are also compared in accordance with increasing deposition temperature. All the films show the optical transmittance over 80% and the film deposited at $250^{\circ}C$ demonstrates the superior resistivity ($1.237{\times}10^{-4}{\Omega}{\cdot}cm$).

• Journal of Nutrition and Health
• /
• 제38권7호
• /
• pp.512-520
• /
• 2005

Phytoestrogens, especially Yak-kong or soybean-derived isoflavones have been traditionally used as a supplement of estrogen for preventing postmenopausal osteoporosis in oriental folk medicine. In a previous study, we demonstrated that as Yak-kong and soybean increased MG-63 human osteoblastic cell proliferation, the expression of estrogen receptor $\alpha\;and\;beta\;(ER\;\alpha:\;ER\;\beta$) both were increased. However, the increased level of ER $\alpha$ is much higher than that of ER$\beta$. To determine whether the altered level of ER $\alpha$ expression affects Yak-kong or soybean induced MG-63 cell proliferation, we established cell lines stably expressing either ER $\alpha$ or antisense ER $\alpha$ RNAs. Increased expression of ER a in MG- 63 cells (ER $\alpha$-MG63) enhanced Yak-kong or soybean induced proliferation which paralleled with the enhanced expression of IGF-I. Inhibition of ER $\alpha$ expression by antisense $ER\;\alpha\;RNAs\;(As-ER\;\alpha-MG63$) caused these cells to insensitize Yak- kong or soybean induced proliferation and IGF-I expression. Furthermore, the comparable effects between Yak-kong and the combined treatment of genistein and daidzein at $0.5\;{\times}\;10^{-8}M$, which is a concentration of these two isoflavones similar to Yak-kong at 0.001 mg/ml, on cell proliferation and IGF-I expression in $ER\;\alpha-MG63\;or\;As-ER\;\alpha-MG63$ cells demonstrate that ER $\alpha$ plays an important, active role in MG-63 cell proliferation induced by phytoestrogens, especially Yak-kong or soybean derived isoflavones.

• 한국응용과학기술학회지
• /
• 제8권2호
• /
• pp.115-122
• /
• 1991

Four novel amphoteric surfactants of N-(2-alkylamidoethyl)-N, N-dimethyl ammonioacetates were synthesized. The each reaction between four saturated fatty acids containing 10, 12, 14 and 16 carbon atoms and N, N-dimethylethylene diamine permitted to give the intermediate products, N-(2-alkylamidoethyl)-N, N-dimethylamines. Quaterinzation of these intermediates was permitted to form N-(2-alkylamidoethyl)-N, N-dimethyl, ammonioacetates, whose sturctures were identified by CC, TLC, elemental analysis, IR pectrophotometry and $^1$HNMR spectrometry. The products yielded from 48% to 58%. The isoelectric points were shown in the range of $4.30{\sim}6.64$. It showed a tendency to learn to the acidic site and its range was broadened as increase of the hydrophobic group length. Surface tensions of the aqueous solution in the $10^{-6}{\sim}10^{-1}$mol/l of amidobetaines were measured. and the critical micell concentration(cmc) were shown in the range of $8.37{\times}10^{-6}{\sim}8.96{\times}10^{-2}$mol/l, and ${\Gamma}_{cmc}$ were reduced to 32.3~38.2 dyne/cm. A linear relationship between log cmc and the number of carbon in the hydrophobic alkyl chain was presented by the formula of log cmc=2.38-0.5n, and the contribution-rate of n on the standard free energy change in micellization ${\partial}({\Delta}G^0$$_m)/{\partial}n$, was calulated as -0.5RT.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.1-1
• /
• 2000

The results of the modification of metal materials treated by high temperature pulst:d plasma fluxes (HTlPPF) with a specific power of incident flux changing in the $(3...100)10^5{]\;}W/cm^2$ range and a pulse duration lying from 15 to $50{\;}\mu\textrm{s}$ have been presented. The results of HTPPF action were studied on the stainless steels of 18Cr-l0Ni, 16Cr- 15Ni, 13Cr-2Mo types; on the structural carbon steels of (13...35)Cr, St. 3, St. 20, St. 45 types; on the tool steels of U8, 65G, ShHI5 types, and others; on nickel and high nickel alloy of 20Cr-45Ni type; on zirconium- and vanadium-base alloys and other materials. The microstructure and properties (mechanical, tribological, erosion, and other properties) of modified materials and surface alloying of metals exposed to HTPPF action have been investigated. It was found that the modification of materials by HTPPF resulted in a simultaneous increase of several properties of the treated articles: microhardness of the surface and layers of 40...60 $\mu\textrm{m}$ in depth, tribological characteristics (friction coefficient, wear resistance), mechanical properties ({\sigma_y}, {\;}{\sigma_{0.2}}.{\;}{\sigma_r}) on retention of the initial plasticity ($\delta$), corrosion resistance, radistanation erosion under ion irradiation, and others. The determining factor of the changes observed is the structural-phase modification of the near-surface layers, in particular, the formation of the fine cellular structure in the near-surface layers at a depth of $20{\;}{\mu\textrm{m}}$ with dimension of cells changing in the range from 0.1 to $1., 5{\;}\mu\textrm{m}$, depending on the kind of material, its preliminary treatment, and the parameters of plasma fluxes. The remits obtained have shown the possibility of purposeful surface alloying of metals exposed to HTPPF action over a depth up to 20...45 $\mu\textrm{m}$ and the concentration of alloying element (Ni, Cr, V) up to 20 wt.%. Possible industrial brunches for using the treatment have been also considered, as well as some results on modifying the serial industrial articles by HTPPF.