• 소성∙가공
• /
• 제18권4호
• /
• pp.317-322
• /
• 2009

Superplastic deformation behavior of a Zn-0.3 wt.% Al was investigated. Grain sizes of $1{\mu}m$ and $10{\mu}m$ were obtained by a thermomechanical treatment. A series of load relaxation and tensile tests were conducted at various temperatures ranging from RT ($24^{\circ}C$) to $200^{\circ}C$. A large elongation of 1400% was obtained at room temperature in the specimens with the grain size of $1{\mu}m$. In the case of specimens with the grain size of $10{\mu}m$, relatively lower elongation at room temperature was obtained and, as the temperature increases above $100^{\circ}C$, a high elongation of about 400 % has been obtained at $200^{\circ}C$ under the strain rate of $2{\times}10^{-4}/s$. Dynamic materials model (DMM) has been employed to explain the contribution from GBS of Zn-Al alloy. Power dissipation efficiency for GBS was evaluated as above 0.4 and found to be very close to the unity as strain rate decreased and temperature increased, suggesting that GBS could be regarded as Newtonian viscous flow.

• 한국전기전자재료학회논문지
• /
• 제21권9호
• /
• pp.848-852
• /
• 2008

Characteristics of microcrystalline-silicon thin-films deposited by plasma-enhanced chemical-vapor deposition (PECVD) method were studied. There were optimum values of RF power density and $H_2$ dilution ratio $(H_2/(SiH_4+H_2))$; maximum grain size of about 35 nm was obtained at substrate temperature of 250 $^{\circ}C$ with RF power density of 1.1 W/$cm^2$ and $H_2$ dilution ratio of 0.91. Larger grain was obtained with higher substrate temperature up to 350 $^{\circ}C$. Grain size dependence on RF power density and $H_2$ dilution ratio could be explained by etching effects of hydrogen ions and changes of species of reactive precursors on growing surface. Surface-mobility activation of reactive precursors by temperature could be a reason of grain-size dependence on the substrate temperature. Microcrystalline-silicon thin-films that could be used for flat-panel electronics such as active-matrix organic-light-emitting-diodes are expected to be fabricated successfully using these results.

• 한국자기학회지
• /
• 제2권3호
• /
• pp.228-232
• /
• 1992

고온초전도체 $Y_1Ba_2Cu_3O_{7-y}$의 grain을 높은 자기장에서 정렬시켜 여러가지 자기적 특성을 조사하였다. Grain이 정렬된 초전도체는 단결정과 같이 Cu-O layer에 수직, 수평 방향에 대해 자기이방성을 가진다. 2~77 K의 온도영역에서 측정한 lower critical field$(H_{c1})$은 온도가 증가하면서 선형적으로 감소하였는데, Cu-O layer에 대하여 외부 자기장이 수직인 경우가 더욱 급격히 감소하였다. 온도변화에 따른 자율화$(4{\pi}\;X)$의 측정으로부터 극저온의 자화율이 -1에 가까운 값을 가진다는 것을 알 수 있었다. 또한 이 자화 곡선을 London의 공식과 two-fluid model을 이용해 최소자승법으로 fitting하여 절대 영도에서 침투깊이$({\lambda}_0)$를 구하였다. 또한 2 K에서 외부 자기장에 따른 자화곡선을 측정하였으며, Bean의 critical state model을 이용한 임계전류밀도$(J_c)$의 계산으로부터 grain내부는 단결정 수준의 높은 $(J_c)$를 가지고 있음을 알 수 있었다.

• 한국환경과학회지
• /
• 제2권4호
• /
• pp.311-316
• /
• 1993

3리터의 실험실 크기의 플러그 흐름의 혐기성 소화기를 사용하여 grain dust로부터 메탄가스를 생산하였다. 이 실험에서 사용한 소화기는 온도(35, 45, 55$^{\circ}C$), 체류 시간(6, 12일), 초기농도(7.8, 9.0% Total Solids)의 함수로 10가지 조건에서 실험이 행하여 졌는데, 실험 결과 55$^{\circ}C$, 6일 HRT, 7.8%TS 에서 가장 높은 메탄가스를 생산하였으며, 실험결과를 토대로 메탄가스생산 관계식을 제시하였다. 또한, 위의 실험의 조건에서는 thermophilic 의 경우가 mesophilic 경우보다 메탄가스 생성이 좋은 것으로 나타났다.

• Progress in Superconductivity
• /
• 제14권1호
• /
• pp.39-44
• /
• 2012

The fabrications condition and superconducting properties of top-seeded melt growth (TSMG) processed $GdBa_2Cu_3O_{7-y}$ (Gd123) bulk superconductors were studied. Processing parameters (a maximum temperature ($T_{max}$), a temperature for crystal growth ($T_G$) and a cooling rate ($R_G$) through a peritectic temperature ($T_P$) for the fabrication of single grain Gd123 superconductors were optimized. The magnetic levitation forces, trapped magnetic fields, superconducting transition temperature ($T_c$) and critical current density ($J_c$) of the Gd123 bulks superconductors were estimated. Single grain Gd123 bulk superconductors were successfully fabricated at the optimized processing condition. The $T_c$ of a TSMG processed Gd123 sample was 92.5 K and the $J_c$ at 77 K and 0 T was approximately $50kA/cm^2$. The trapped magnetic field contour and magnetic levitation forces were dependent on the top surface morphology of TSMG processed Gd123 samples. The single grain Gd123 samples, field-cooled at 77 K using a Nd-B-Fe permanent magnet with 5.27 kG and 30 mm dia., showed the trapped magnetic field contour of a single grain with a maximum of 4 kG at the sample center. The maximum magnetic levitation forces of the single grain Gd123 sample, field-cooled or zero field-cooled, were 40 N and 107 N, respectively.

• 한국재료학회지
• /
• 제26권11호
• /
• pp.590-597
• /
• 2016

In this study, six kinds of low-carbon steel specimens with different ferrite-pearlite microstructures were fabricated by varying the Nb content and the transformation temperature. The microstructural factors of ferrite grain size, pearlite fraction, interlamellar spacing, and cementite thickness were quantitatively measured based on optical and scanning electron micrographs; then, Charpy impact tests were conducted in order to investigate the correlation of the microstructural factors with the impact toughness and the ductile-brittle transition temperature (DBTT). The microstructural analysis results showed that the Nb4 specimens had ferrite grain size smaller than that of the Nb0 specimens due to the pinning effect resulting from the formation of carbonitrides. The pearlite interlamellar spacing and the cementite thickness also decreased as the transformation temperature decreased. The Charpy impact test results indicated that the impact-absorbed energy increased and the ductile-brittle transition temperature decreased with addition of Nb content and decreasing transformation temperature, although all specimens showed ductile-brittle transition behaviour.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권2호
• /
• pp.158-164
• /
• 1995

Solid solutions Sr$_{2}$(Ta$_{1-x}$ Nb$_{x}$)$_{2}$O$_{7}$, (x=0.0-1.0), composed of strontium tantalate(Tc=-107.deg. C) and strontium-niobate(Tc=1342.deg. C) were prepared by the conventional mixed oxide method and the flux method(molten salt synthesis method). Phase relation, sintering temperature, grain-orientation and dielectric properties for sintered ceramic samples were investigated with different compositions. Both Curie temperature and dielectric constant at Curie temperature were increased, and sintering behavior and the degree of grain-orientation were improved with the increase of Nb content. The single phase Sr$_{2}$(Ta/sib 1-x/Nb$_{x}$)$_{2}$O$_{7}$ powder was synthesized by using the flux method at lower temperatures, and sintering temperature was also reduced by using the flux method-derived powder than using the mixed oxide-derived powder. Sintering characteristics and dielectric properties of the specimens prepared by the flux method were better than those derived through the conventional mixed oxide method.thod.hod.

• International Journal of Korean Welding Society
• /
• 제2권1호
• /
• pp.25-28
• /
• 2002

In the coarse grain HAZ adjacent to the fusion line, most of the TiN particles in conventional Ti added steel are dissolved and austenite grain growth is easily occurred during welding process. To avoid this difficulty, thermal stability of TiN particle is improved by increasing the nitrogen content in steel. In this study, the effect of hlgh nitrogen TiN particle on preventing austenite grain growth in HAZ was investigated. Increased thermal stability of TiN particle is helpful for preventing the austenite grain growth by pinning effect. High nitrogen TiN particle in simulated HAZ were not dissolved even at high temperature such as 1400'E and prevented the austenite grain growth in simulated HAZ. Owing to small austenite grain size in HAZ the width of coarse grain HAZ in high nitrogen TiN steel was decreased to 1/10 of conventional TiN steel. Even high heat input welding, the microstructure of coarse grain HAZ consisted of fine polygonal ferrite and pearlite and toughness of coarse grain HAZ was significantly improved.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.126-127
• /
• 2006

In this study, nano grain W is fabricated by Severe Plastic Deformation-Powder Metallurgy (SPD-PM) process. W powder and W-Re powder mixtures are processed by SPD-PM process, a Mechanical Milling (MM) process. As results, a nano grain structure, whose grain size is approximately 20nm, is obtained in W powder after MM for 360ks. A nano grain W compact, whose grain size 630nm, has excellent deformability above 1273K. A nano grain W-10Re compact is composed of equiaxed grain, a grain growth is restrained and has low dislocation density after the large deformation; therefore it is considered that W-Re compact shows superplasticity.

• 한국분말재료학회지
• /
• 제25권2호
• /
• pp.104-108
• /
• 2018

Grain-growth behavior in the $95Na_{1/2}Bi_{1/2}TiO_3-5BaTiO_3$ (mole fraction, NBT-5BT) system has been investigated with the addition of $Na_2CO_3$. When $Na_2CO_3$ is added to NBT-5BT, the growth rate is higher than desired and grains are already impinging each other during the initial stage of sintering. The grain size decreases as the sintering temperature increases. With the addition of $Na_2CO_3$, a liquid phase infiltrates the interfaces between grains during sintering. The interface structure can be changed to be more faceted and the interface migration rate can increase due to fast material transport through the liquid phase. As the sintering temperature increases, the impingement of abnormal grains increases because the number of abnormal grains increases. Therefore, the average grain size of abnormal grains can be decreased as the temperature increases. The phenomenon can provide evidence that grain coarsening in NBT-5BT with addition of $Na_2CO_3$ is governed by the growth of facet planes, which would occur via mixed control.