• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.12
• /
• pp.9-17
• /
• 2006

An experimental study was carried out to examine the behavior of the unsteady boundary layer. An NACA 0012 airfoil with aspect ratio of 2.7 was set vertically in a test section, which is sinusoidally pitched about the quarter chord. The oscillating amplitude is from -6$^{\circ}$ to +6$^{\circ}$ and the mean angle of attack is 0$^{\circ}$. Surface mounted probes (Glue-on probes) were employed to measure the surface flow of the boundary layer. Measurements were made at free-stream velocities of 1.98, 2.83, and 4.03m/s, and the corresponding Reynolds numbers based on the chord length were 2.3$\times$104, 3.3$\times$104 and 4.8$\times$104, respectively. The reduced frequency is fixed as 0.1 in all cases. The results show that the surface position of minimum shear stress and of boundary layer break-down can be discerned in the Reynolds number between 2.3$\times$104 and 3.3$\times$104.

• Journal of Trauma and Injury
• /
• v.25 no.2
• /
• pp.57-62
• /
• 2012

Gunshot wounds are rare in Korea, but they have tended to increase recently. We experienced an interesting case of penetrating gunshot injuries to the cervical spine with migration the fragments of the bullet within the dural sac of the cervical spine, so discuss the pathomechanics, treatment and complications of gunshot wounds to the spine and present a review of the literature. A 38-year-old man who had tried to commit suicide with a gun was admitted to our hospital with a penetrating injury to the anterior neck. the patient had quadriplegia. A Computed tomography (CT) scan and 3-dimensional CT of the spine showed destruction of the left lateral mass and lamina of the 5th cervical vertebra; the bullet and fragments were found at the level of the 5th cervical vertebra. The posterior approach was done. A total laminectomy and removal of the lateral mass of the 5th cervical vertebrae were performed, and bone fragments and pellets were removed from the spinal canal, but an intradurally retained pellets were not totally removed. A dural laceration was noted intraoperatively, and CSF leakage was observed, so dura repair was done watertightly with prolene 6-0. The dura repair site was covered with fibrin glue and Tachocomb$^{(R)}$. Immediately, a lumbar drain was done. Radiographs included a postoperative CT scan and X-rays. The postoperative neurological status of the patient was improved compared with the preoperative neurological status. however, the patients developed symptoms of menigitis. He received lumbar drainage(200~250 cc/day) and ventilator care. After two weeks, panperitonitis due to duodenal ulcer perforation was identified. Finally, the patient died because of sepsis.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.53-61
• /
• 2017

In this study, specimens were produced with a column member and a wooden gusset only by inserting an wooden gusset which is a substitute for steel plate into the center of a slit-processed column member. The moment resistance performance of the specimens was compared with that of control specimens that used a steel plate. The measured maximum moments of the specimens produced with GFRP-reinforced wooden laminated gussets and pins were lower by 24% on average compared to the steel plate-inserted specimens, but they showed good toughness. The fracture shape suggests that it was fractured along the annual rings between the pin and the end of the column member. The rigid specimen that integrated a laminated wood and a wooden laminated gusset with adhesive showed 2.8 times greater initial rigidity and 40% greater maximum moment on average compared to the control specimen. The rigid specimens mainly fractured on a glulam around glue line.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.6
• /
• pp.907-916
• /
• 2020

This research was conducted to investigate the linear expansion and resistance properties of a composite board (com-ply). This board was made of medium-density fiberboard (MDF) laminated using avocado (Persea americana), mahogany (Swietenia mahogani), and pine (Pinus merkusii) veneers. These three types of veneers were laminated on both surfaces of the MDF using adhesives, namely, epoxy and isocyanate. Glue (250 g·m^-2) was spread on the surface, followed by cold press for 3 h with an applied pressure of 15 kg·cm^-2. The research result revealed that com-ply exhibited an increased dimensional stability compared with MDF, indicated by reduction in water absorption, thickness swelling, and linear expansion. The com-ply made of the pine veneer and isocyanate adhesive exhibited high density, water absorption, thickness swelling, and screw withdrawal load. The com-ply that exhibited the strongest resistance to drywood termite attacks was the one made of the mahogany veneer and isocyanate adhesive. Moreover, the com-ply that exhibited the biggest weight loss (3.6 %) was made of the pine veneer and epoxy adhesive. The results of this research may facilitate in manufacturing com-ply using the selected veneer and adhesive without the application of hot press.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.3
• /
• pp.51-56
• /
• 2016

The most widely used glue in a corrugator is starch, which is a natural polymer. This material needs thermal energy to achieve a binding force, so a heating section is installed in a corrugator. However, this heating section can cause quality problems in linerboards and corrugating medium and increase the production cost because of the high cost of fossil resources. Therefore, a new adhesive that provides the binding force at lower temperatures than the conventional one must be developed. In this study, SB-latex was selected as a co-adhesive and added to the starch solution. The addition of the SB-latex was determined based on the viscosity of the new adhesive. The adhesive strength and the drying energy reduction of a corrugated board were measured to evaluate the functionalities of the new adhesive. The addition of SB-latex was determined to be under 20% of the oven-dried starch based on the viscosity of the new adhesive. The adhesive strength was improved and the drying energy was reduced by applying the new adhesive.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.2
• /
• pp.20-25
• /
• 1989

This study was carried out in order to investigate the treatment effect of PEG soln which is a common dimensional stabilizer to green log. sawing panel etc, on bonding product including plywood widely-used in secondary processing unit. The 30% concentration of aqueous PEG soln. with molecular weight of 400, 1.000 and 4,000 were prepared respectively, and also dipping the veneer in the PEG soln. spreading the PEG soln. on veneer and mixing the PEG soln. in the adhesive were allowed. Then the ratio of PEG impregnation on veneer, the adhesive strength of plywood were epitomized as follows: The ratio of impregnation by PEG 4,000 at dipping condition was highest. while that by PEG 400 at same condition was lowest. However, the effect of PEG molecular weight on the ratio of impregnation at spreading condition did not occur. 2. The adhesive strength was great in the order of 4,000>400>1,000 in molecular weight of PEG at dipping and spreading conditions. In case of mixing the PEG soln. in the adhesive, the adhesive strength was great in the order of 400>1,000>4,000 in molecular weight of PEG. Throughout three treatment conditions, PEG 400 was relatively favourable with about 10kg/$cm^2$ dry strength. 3. The adhesive strength was great 10 the order of spreading >dipping >mixing condition. 4. Although adhesive strength with the 30% concentration of aqueous PEG soln. was decreased by 35% and over, compared to control (non-treatment) adhesive strength, all types of PEG treatment except mixing the PEG soln. in the adhesive exceeded the standard dry strength for common use panel. 7.5kg/$cm^2$. 5. In warm water-proof test, the adhesive strengths by all PEG treatment conditions were less than the standard wet strength, 7.5kg cot, and also delamination of glue line occured mostly in mixing in the PEG soln. in the adhesive condition.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.2
• /
• pp.196-205
• /
• 2020

The purpose of this study was to investigate a method for improving the physical and mechanical properties of laminated board made from oil palm trunk (OPT). The effects of pretreating the lamina with heat-pressure and altering the lamina composition of the laminated board were investigated. The outer third of OPT in cross-section had high-density wood, while the underlying third had low to medium density. The hot press was applied to pretreat the lamina that had low to medium density. The lamina were 1.5 cm in thickness, 5 cm in width, and 65 cm in length. The hot press was applied at 2.94 MPa or 4.41 MPa at 150 ℃ for 60 minutes, and the target thickness of the lamina was 1 cm. The three layers of the laminated board samples were bonded with isocyanate adhesive at a glue spread of 300 g/㎡ and cold pressed at 0.98 MPa for 3 h. The laminated board samples were tested according to Japanese Agricultural Standard (JAS) 234-2003. The results showed that the densification of the inner lamina did not significantly affect the physical-mechanical properties of the laminated board produced. However, the laminated board made with high-density laminas for the outer layers fulfilled the JAS 234-2003 standard for the modulus of elasticity and the modulus of rupture.

• Journal of the Korea Furniture Society
• /
• v.18 no.2
• /
• pp.91-99
• /
• 2007

Modernity which is superficial phenomenon set off the mass scale for mass consumption and provide uniformly artificial environment. But natural destruction, environment pollution, resources exhaustion and so on has been caused by this and now ecology is threatened by destruction and damage beyond the limitation and human beings survival is even threatened. Accordingly furniture development for environment preservation considered environment problem is the urgent real situation. Recent paradigm is the concept of Eco-design which is the green design possible to live together in symbiosis, and new types of alternative furniture are needed in Korea as well. 'Furniture for disassembly' is presented as new method for alternative furniture. Furniture for disassembly can be presented by mainly two directions. The first main characteristic is what is assembled by the use of woodworking joints technique as an assembly structure system without any hardware. The second is what is presented as the structure possible to be assembled by simple manual tools with hardware without any glue. The advantages of furniture for disassembly are environment preservation, space application, transportation efficiency and shapeliness. In manufacture method which is different from present furniture, the application of traditional truss technique which uses various types of custom-made and connection technique in case of assemble structure system without hardware is the typical differences. This assembly method expects not only interest induction about assembly and disassembly of diagram per sub materials but also the development of emotion, the improvement of collaboration, space perception ability and shape sense, the improvement of solid body structure insight and so on, when it use in the furniture for children with the application to many kinds of structure with BANGDOOSANJ (Wedged), JUMUGJANGBU (Dovetail) or NABIEUNJANG (Dovetail Keys) and so on.

• The Korean Journal of Physiology and Pharmacology
• /
• v.18 no.3
• /
• pp.249-254
• /
• 2014

The purpose of this study is to characterize the effects of KHG26792 (3-(naphthalen-2-yl(propoxy)methyl)azetidine hydrochloride), a potential skin whitening agent, on melanin synthesis and identify the underlying mechanism of action. Our data showed that KHG26792 significantly reduced melanin synthesis in a dose-dependent manner. Additionally, KHG26792 downregulated microphthalmia-associated transcription factor (MITF) and tyrosinase, the rate-limiting enzyme in melanogenesis, although tyrosinase was not inhibited directly. KHG26792 activated extracellular signal-regulated kinase (ERK), whereas an ERK pathway inhibitor, PD98059, rescued KHG26792-induced hypopigmentation. These results suggest that KHG26792 decreases melanin production via ERK activation. Moreover, the hypopigmentary effects of KHG26792 were confirmed in a pigmented skin equivalent model using Cervi cornus Colla (deer antler glue), in which the color of the pigmented artificial skin became lighter after treatment with KHG26792. In summary, our findings suggest that KHG26792 is a novel skin whitening agent.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.41.2-41.2
• /
• 2011

Recently, scaling down of ULSI (Ultra Large Scale Integration) circuit of CMOS (Complementary Metal Oxide Semiconductor) based electronic devices become much faster speed and smaller size than ever before. However, very narrow interconnect line width causes some drawbacks. For example, deposition of conformal and thin barrier is not easy moreover metallization process needs deposition of diffusion barrier and glue layer. Therefore, there is not enough space for copper filling process. In order to overcome these negative effects, simple process of copper metallization is required. In this research, Cu-V thin alloy film was formed by using RF magnetron sputter deposition system. Cu-V alloy film was deposited on the plane $SiO_2$/Si bi-layer substrate with smooth and uniform surface. Cu-V film thickness was about 50 nm. Cu-V layer was deposited at RT, 100, 150, 200, and $250^{\circ}C$. XRD, AFM, Hall measurement system, and XPS were used to analyze Cu-V thin film. For the barrier formation, Cu-V film was annealed at 200, 300, 400, 500, and $600^{\circ}C$ (1 hour). As a result, V-based thin interlayer between Cu-V film and $SiO_2$ dielectric layer was formed by itself with annealing. Thin interlayer was confirmed by TEM (Transmission Electron Microscope) analysis. Barrier thermal stability was tested with I-V (for measuring leakage current) and XRD analysis after 300, 400, 500, 600, and $700^{\circ}C$ (12 hour) annealing. With this research, over $500^{\circ}C$ annealed barrier has large leakage current. However V-based diffusion barrier annealed at $400^{\circ}C$ has good thermal stability. Thus, thermal stability of vanadium-based thin interlayer as diffusion barrier is good for copper interconnection.