• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.226-230
• /
• 1997

A plasticity theory applicable to powdered metal compaction is briefly summarized and its variational form for the finite element analysis is described. The compaction processes of axisymmetric solid cylinder are simulated. For the analysis of the friction effect of solid cylinder, the investigations were performed for different compact geometries. Highlights of the results for given geometries are reported in terms of transmitted pressure on the lower punch from the upper punch through the compact and maximum density variation within the compacts. General conclusions from these simulation results are : (1) the friction coefficient could be selected from the transmitted force data during the single acting compaction test with the simulated results ; and (2) density variatioins within the compacts are very much dependent of the compact geometry such as the height to diameter ratio and the frictional condition between compact and dies.

• 수산해양기술연구
• /
• 제34권3호
• /
• pp.339-345
• /
• 1998

The purpose of this paper is to investigate the effect of the specimen geometries on the pin bearing strength of the angle ply carbon fiber reinforced composites. The effect of the edge distance and the specimen width on the pin bearing strength of angle ply CFRP composites are experimentally investigated in this paper. As results, the failure mode and pin bearing strength of mechanical joints turned out to depends on the stacking sequence and specimen geometries such as the edge distance and the specimen width. The higher pin bearing strength obtained for the angle ply CFRP composites is attributed to a combination of debonding, pull out, buckling and breakage of fiber and also the matrix cracking.

• Computers and Concrete
• /
• 제20권1호
• /
• pp.57-63
• /
• 2017

A coupled experimental-numerical study on shear fracture in concrete specimens with different geometries is carried out. The crack initiation, propagation and final breakage of concrete specimens are experimentally studied under compression loading. The load-strain and the strength of the specimens are experimentally measured, indicating decreasing effects of the shear behavior on the failure load of the specimen. The effects of specimen geometries on the shear fracturing path in the concrete specimens are also investigate. Numerical models using an indirect boundary element method are made to evaluate the crack propagation paths of concrete specimens. These numerical results are compared with the performed experiments and are validated experimentally.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.536-541
• /
• 2000

A low cost PC based simulator for excavator manipulation has been developed using virtual reality technology. The simulator consists of two joystick input devices, server and client PCs, an excavator kinematics module, and a graphic rendering program Open Inventor. In order to use two joysticks in the PC window environment multi-thread programing with network protocol TCP/IP has been used. To provide realistic view to the operator, CAD program Pro/Engineer and 3D modeller have been employed to create 3D part geometry of tile manipulator and virtual environmental geometries. Those geometries also have been transformed and imported to the Open Inventor. The Simulator developed is to be improved for more realistic excavator operational training.

• 대한기계학회논문집A
• /
• 제32권12호
• /
• pp.1063-1071
• /
• 2008

This paper provides a failure pressure evaluation model for local wall-thinned elbows. In this study, parametric finite element analyses are performed on the elbows containing local wall-thinning defect at their intrados and extrados, and the failure pressures are obtained from the analysis results by applying a local failure criterion that was validated by real-scale pipe tests. An evaluation model including the effects of thinning depth, length, circumferential angle, thinning location, and elbow geometries on the failure pressure is derived based on the evaluated failure pressures. The proposed model agrees well with the results of finite element analyses and reasonably estimates the dependence of failure pressure on the wall-thinning dimensions and elbow geometries. Also, the comparison with experimental data demonstrates that the proposed evaluation model can accurately predict the failure pressure of local wall-thinned elbows.

• 한국분무공학회지
• /
• 제9권1호
• /
• pp.1-7
• /
• 2004

This paper describes the characteristics of injection rate and macroscopic behavior of fuel spray injected from common-rail type diesel injectors with different nozzle geometries. The injection rates according to the nozzle geometries were measured at different energizing duration of the injector solenoid and injection pressure by using the Bosch's injection rate meter based on the pressure variation in the tube. The spray behaviors injected from the different nozzles were visualized using the spray visualization system composed of an Ar-ion laser, an ICCD camera, and a synchronization system at various injection and ambient pressures. It is revealed that VCO nozzle has higher spray tip velocity at the early stage of injection duration and wider spray cone angle than the mini-sac nozzles. Also the spray cone angle is increased with the increase of nozzle diameter.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 금형가공 심포지엄
• /
• pp.308-315
• /
• 2002

In recent automotive industries, fine blanking technology widely used in production of components with relatively thick gauges in brake systems, seat recliner, door locks, and auto transmission systems. Due to its advantages to obtain almost final product quality using fine blanking forming process without additional finish machining processes, consequently saving the production costs. In this paper we intended to develope the small sized module gear toothed dual seat recliner sector gear(0.5mm module) for car seats using fine blanking process which needed semi piercing with computer simulation and a lot of try and errors to achieve required accuracy and geometric quality. However through the some corrections of tool geometries with tryout test, we could get successful results.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.419-420
• /
• 2006

This paper deals with a hex-dominant mesh generation using an advancing front method for three-dimensional geometries. Hexahedral and prismatic meshes are generated inwardly by offsetting from initial boundary mesh. When the meshes intersect with each other after offsetting, overlapped meshes are improved by node relocation method. In order to generate conforming mesh, pyramid elements are inserted between hexahedral and tetrahedral elements. Sample meshes fur several geometries are presented and analized to demonstrate the effectiveness of the proposed algorithm.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.22-22
• /
• 2009

Laser forming is a promising technology in manufacturing, such as in the shipbuilding, automobile, microelectronics, aerospace and other manufacturing industries. This process forms the sheet metal by utilization of laser-induced thermal stresses. Laser forming process has been studied extensively for rectangular shape geometry. This basic study presents the change in deformation behavior of sheet metal during transition from linear to curved geometries and irradiations as well. A series of experiments have been conducted on a wide range of specimen geometries such as quarter-circular and half circular plate. The reasons for this behavior have been analyzed. Results are compared and analyzed by simulations using ABAQUS. Influence of developed stresses on the bending has been investigated. This study provides the more understanding of forming mechanism influenced by geometry effect.

• 한국가시화정보학회지
• /
• 제5권2호
• /
• pp.56-63
• /
• 2007

Flow visualization and aerodynamic characteristics of delta wings with two different leading edge geometries are investigated by PIV system and wind tunnel balance when the Reynolds number is about based on the freestream velocity and the root chord length. Delta wing models have 65-deg swept angle, and the leading edge shapes are divided into round- and sharp- type. The experimental results indicated that the leading-edge vortex strength and aerodynamic coefficient in the round leading edge are stronger and more, respectively than those in the sharp one. Therefore the flow interactions between vortices and the boundary layer are more desirable or more rapidly swirled in the round-type leading edge.